• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.117.1-117
• /
• 2002

$\textbullet$ Evaluation techniques of mobility $\textbullet$ Position characteristics $\textbullet$ Path characteristics $\textbullet$ Evaluation techniques of navigation $\textbullet$ Standard measurement environment $\textbullet$ Evaluation program and equipments $\textbullet$ A measurement experiment

• 오토저널
• /
• 제10권5호
• /
• pp.42-53
• /
• 1988

The effects of ignition position on combustion in a chamber with swirl flow were investigated by use of hot wire anemometer, high speed schlieren photography, and chamber pressure measurement. In experiments, the closed-constant volume combustion chamber was used, and the swirl was formed unsteadily by suction of external fluid after reducing pressure in the chamber. Results show that the effect of ignition position on combustion depends on the flow state and the flame propagation distance corresponding to each ignition position. Also, the effect of combustion promoting increases as an ignition position moves from the center of chamber to the outside, but maximum burning pressure was obtained at the position that is the shortest flame propagation distance.

• 한국정밀공학회지
• /
• 제24권6호
• /
• pp.66-71
• /
• 2007

Development of a locomotive mechanism for the capsule type endoscopes will largely enhance their ability to diagnose disease of digestive organs. As a part of it, there should be provided a detection device of their position in human organs for the purpose of observation and motion control. In this paper, a permanent magnet outside human body was employed to project magnetic field on a capsule type endoscope, while its position dependent flux density was measured by three hall-effect sensors which were orthogonally installed inside the capsule. In order to detect the 2-D position data of the capsule with three hall-effect sensors including the roll, pitch and yaw angle, the permanent magnet was extra translated during the measurement. In this way, the 2-D coordinates and three rotation angles of a capsule endoscope on the same motion plane with the permanent magnet could be detected. The working principle and performance test results of the capsule position detection device were introduced in this paper showing that they could be also applied to 6-DOF position detection.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.56-59
• /
• 2005

This paper describes a novel method of detecting excitation position in Switched Reluctance Motor(SRM) drive. Some strategics for position sensorless control methods of the SRM include the measurement of phase current. The principle of the rotor position estimation is based on the defection of phase current according to rotor position. This sensorless method is very simple to detect excitation position estimation and gives efficient control of drive system. The suggested method is verified by some simulations and experimental tests

• Nuclear Engineering and Technology
• /
• 제56권3호
• /
• pp.916-921
• /
• 2024

The control rod worth sensitivity to the neutron detector position in the rod drop experiment is studied by the time-dependent Monte Carlo (TDMC) neutron transport calculations for AGN-201K educational reactor and the Kyoto University Critical Assembly. The TDMC simulations of the rod drop experiments are conducted by the Seoul National University Monte Carlo (MC) code, McCARD, yielding time-dependent neutron densities at detector positions. The detector-position-dependent results of the total control rod worth calculated by the extrapolation, the integral counting, and the inverse methods are compared with the numerical reference using the MC eigenvalue calculations and the experimental results. From these comparisons, it is observed that the total control rod worth can be estimated with a considerable difference depending on the detector position through the rod drop experiment. The proposed TDMC simulation of the rod drop experiment can be applied for searching a better detector position or quantifying a bias for the control rod worth measurement.

• 한국지능시스템학회논문지
• /
• 제24권4호
• /
• pp.424-429
• /
• 2014

본 논문에서는 발광광고물의 휘도를 측정하는 영상기반 휘도측정시스템을 제안한다. 제안하는 휘도측정시스템은 DSLR 카메라의 영상을 이용하여 점휘도계의 효율성과 면휘도계의 휴대성 및 경제성의 단점을 보완하며, 대상의 전체적인 휘도를 측정하는 시스템으로 영상을 입력받아 휘도분석 알고리즘을 통해 실시간으로 휘도값이 출력되도록 설계하였다. 측정 대상인 발광광고물은 설치 위치, 크기, 모양이 다양하며, 발광광고물의 휘도는 측정 거리, 각도, 색 등 다양한 조건에 따라 측정값이 달라진다. 따라서 정확한 휘도를 측정하기 위하여 측정대상물과의 거리에 따른 휘도값의 변화를 측정하였고, 측정 거리가 증가하면 휘도값이 변화하는 것을 고찰하였다. 실험을 통하여 측정 위치와 휘도값의 연관성을 수식으로 나타내었고, 제안한 방법을 평가하기 위해 점휘도계를 이용한 측정값과 비교 실험을 진행하였다.

• 제어로봇시스템학회논문지
• /
• 제21권12호
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• 복식문화연구
• /
• 제12권6호
• /
• pp.933-944
• /
• 2004

This study was aimed to provide the fundamental and various measurement data of the head and face for male children. Two hundred forty one male children, aged nine to twelve years, participated for this study. The 31 regions on the head and face of the subjects were directly measured by the expert experimenters. Through factor analysis, the six factors were extracted upon factor scores and those factors comprised $67.47\%$ for the total variances. The first factor was described the general height elements for the mouth and the environs of the mouth. The second factor was described the general height around the nose, forehead and eyes. The third factor was described the height of the ear environs. The forth factor contained the length around the sinciput to the occiput, the head thick and the head circumstance. The fifth factor was described the general width of the outer head and the corner of the eyes. The last factor contained the depth of the mouth and nose. Four clusters as their head and face shape were categorized using six factor scores by cluster analysis. Type 1 was characterized by the shortest head and face width, surface length and girth, and the shorter length of head, but the highest position of chin, philtrum, upper lip. Type 2 was characterized by the shortest head and face length and thickness, and the lowest position of the forehead, eye, nose, mouth, ear environs, but that had wider width of head and face. Type 3 was characterized by the longest and the widest head and face type, and the highest position of the mouth. Type 4 was characterized by longer length of head and face, and the widest head girth and largest head thickness, and the highest position of the forehead, eye, nose environs. And this type had the widest width of nose and mouth, and the longest head surface length.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.50-50
• /
• 2000

In this paper, a new measuring system is :proposed which can measure the fine 6-DOF displacement of rigid bodies. Its measurement principle is based on detection of laser beam reflected from a specially fabricated mirror that looks like a triangular pyramid having an equilateral cross-sectional shape. The mirror has three lateral reflective surfaces inclined 45$^{\circ}$ to its bottom surface. We call this mirror 3-facet mirror. The 3-facet mirror is mounted on the object whose 6-DOF displacement is to be measured. The measurement is operated by a laser-based optical system composed of a 3-facet mirror, a laser source, three position-sensitive detectors(PSD). In the sensor system, three PSDs are located at three corner points of a triangular formation, which is an equilateral triangular formation tying parallel to the reference plane. The sensitive areas of three PSDs are oriented toward the center point of the triangular formation. The object whose 6-DOF displacement is to be measured is situated at the center with the 3-facet mirror on its top surface. A laser beam is emitted from the laser source located at the upright position and vertically incident on the top of the 3-fatcet mirror. Since each reflective facet faces toward each PSD, the laser beam is reflected at the 3-facet mirror and splits into three sub-beams, each of which is reflected from the three facets and finally arrives at three PSDs, respectively. Since each PSD is a 2-dimensional sensor, we can acquire the information on the 6-DOF displacement of the 3-facet mirror. From this principle, we can get 6-DOF displacement of any object simply by mounting the 3-facet mirror on the object. In this paper, we model the relationship between the 6-DOF displacement of the object and the outputs of three PSDs. And, a series of simulations are performed to demonstrate the effectiveness of the proposed method. The simulation results show that the proposed sensing system can be an effective means of obtaining 3-dimensional position and orientation of arbitrary objects.

• 한국정밀공학회지
• /
• 제33권4호
• /
• pp.295-301
• /
• 2016

The out-of-squareness is one of the error sources that affect the positioning accuracy of machine tools and coordinate measuring machines. Laser interferometer is widely used to measure the position and angular errors, and can measure the squareness using an optical square. However, the squareness measurement using the laser interferometer is difficult, as compared to other errors due to complicated optics setup and Abbe's error occurrence. The effect of out-of-squareness mainly appears at the face-diagonal of the movable plane. The diagonal displacements are also affected by the position dependent geometric errors. In this study, the squareness estimation techniques via diagonal displacement measurement using the laser interferometer without an optical square were proposed. For accurate estimation and measurement time reduction, the errors selected from proposed discriminant were measured. Discrepancy between the proposed technique with the laser interferometer (with an optical square) result was $0.6{\mu}rad$.