• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.242-246
• /
• 1996

Accurate measurements of burr profile and burr size are very important for the automation of deburring. In this paper, a new burr measurement system using capacitance sensor is proposed. Ultra precision milling machine was used as a sensor positioning system. The possibility and limitation of employing a capacitance sensor to defect burrs are also investigated. The proposed system is proven to be relatively accurate, easy to setup and lower cost. This system will be applicable to a fully automated deburring system with minor modifications.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.1073-1077
• /
• 1996

This paper presents a recoil and counter recoil(R&CR) motion measurement method using linear variable differential transformers(LVDT). The output of a LVDT is obtained from the differential voltage of the 2nd transformers. As a sensor core is attached at the motion body, the output is directly proportional to the core motion. Displacement, velocity and acceleration are measure from the core length. With a comparison between the measurement result and the known value which is obtained by the precision steel tape, the accuracy and the usefulness of the proposed scheme is validated.

• 한국정밀공학회지
• /
• 제4권3호
• /
• pp.52-59
• /
• 1987

The flatness of a precision surface plate is generally measured by using precision angular measuring instruments such as laser interferometers, autocollimators and electronic levels. Since these instruments are expensive and measurement procedures are complex, such methods are not widely used in industries. In this study, an electronic micrometer that is easy to use and inexpensive to produce was developed in order to solve this problem. The flatness of a black granite surface plate, measured using this device was compared with the values obtained by using the conventional three methods. The results were consistent within ${\pm}1{\mu}m$. It proves that the flatness measuring method using electronic micrometers can be utilized for quantitative measurement. An accessory device that can improve the precision of measurement by attaching to the electronic micrometer was also designed and fabricated.

• 조명전기설비학회논문지
• /
• 제30권2호
• /
• pp.37-42
• /
• 2016

This paper proposes a method to develop a high-precision dimension measurement system using a linear variable differential transformer sensor. The Dimension targets for measurement is carbon material vanes of key element in the rotating parts within vehicle circulating pump. Data acquisition system for dimension measurement is designed using the NI Compact RIO. And the program applying the dimension measurement algorithm is built using NI LabVIEW. The dimension measuring program is composed of a FPGA program, Real Time program and Host program. The method of the experiment compares master vane with target vane for measure the length of the carbon material vane. The experimental results confirmed the usefulness of the accuracy within ${\pm}4um$.

• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.55-61
• /
• 2005

The machining Parts must be Produced within the specification of drawing and those will be able to meet faction and efficiency. At that time, it is very important not only precision machine and machining technique but also the measurement technique. So, the improvement of measurement technique is to be joined together at once with improvement of machining technique. Finally, the quality and value of the parts are decided by precision measurement. This paper aims to study on the measurement uncertainty when the machined parts are inspected with 3-dimensional coordinate measuring machine. The objectives remove an error of measurement and remove a quality of mass products.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.198-203
• /
• 1998

To acquire the high precision of profile for standard electrode of loss angle, it is needed ultraprecision machining technology like MEAP(Magnetic Electronic Abrasive Polishing) and the very high profile measurement technology which can measure a micro unit about the workpiece. So, in this paper, it was developed the measurement system of precision of profile using non-contactable sensor that was approximate sensor of capacitance type, because that is better than others in the electrical characteristics. And standard electrode of loss angle was machined by the MEAP machining technology. In this study, it was development of precision measurement system. This system could be used measure the workpiece of roundness and straightness much more precise and faster than general mechanical measurement system done before. And it could be helped to minimize machining time and planning by very fast and precise measurement about the workpiece.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅳ
• /
• pp.2323-2326
• /
• 2003

Theoretical analysis of the depth measurement system with the use of a single camera and a rotating mirror has hem done. A camera in front of a rotating mirror acquires a sequence of reflected images, from which depth information is extracted. For an object pint at a longer distance, the corresponding pixel in the sequence of images moves at a higher speed. In this paper, the principle d the depth measurement-based on the relation of the pixel movement speed and the depth of objects have been investigated. Also, necessary mathematics to implement the technique is derived and presented. The factors affecting the measurement precision have been studied Analysis shows that the measurement m increases with the increase of depth. The rotational angle of the mirror between two image-takings also affects the measurement precision. Experimental results using the real camera-mirror setup are reported.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.107-113
• /
• 2013

When the main spindle of high precision machine tools are run many hours, heat is generated in bearing parts of the inside of the spindle. Also, headstock is appeared distortion by inside and outside temperature difference of a machine. This paper studies method to measure behavior of machine tool about these thermal effects. In addition, it estimates measurement uncertainty factors which can be appeared in thermal effects measurement. Finding the factor of thermal affect measurement is important for estimation of measurement uncertainty. This paper measures thermal effects of high precision machine tools and evaluates the important factors of uncertainty.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.955-956
• /
• 2010

• 한국정밀공학회지
• /
• 제24권11호
• /
• pp.37-43
• /
• 2007