• Journal of the Korean Geosynthetics Society
• /
• v.20 no.4
• /
• pp.85-93
• /
• 2021

The seventy percentage of Korean Peninsular is covered by the mountainous area, and the depth of west sea and south sea is relatively shallow. Therefore, a large scale land reclamation from the sea has been implemented for the construction of industrial complex, residental area, and port and airport facilities. The common problem of reclaimed land is consisted of soft ground, and hence it has low load bearing capacity as well as excessive settlement upon loading on the ground surface. The hollow concrete block has been used to reinforce the loose and soft foundation soil where the medium-high apartment or one-story industrial building is being planned to be built. Recently the earthquakes with the magnitude of 4.0~5.0 have been occurred in the west coastal and southeast coastal areas. Lee (2019) reported the advantages of hollow concrete block reinforced shallow foundation through the static laboratory bearing capacity tests. In this study, the dynamic behavior of hollow concrete block reinforced sandy ground with filling the crushed stone in the hollow space has been investigated by the means of shaking table test with the size of shaking table 1000 mm × 1000 mm. Three types of seismic wave, that is, Ofunato, Hachinohe, Artificial, and two different accelerations (0.154 g, 0.22 g) were applied in the shaking table tests. The horizontal displacement of structure which is situated right above the hollow concrete block reinforced ground was measured by using the LVDT. The relative density of soil ground are varied with 45%, 65%, and 85%, respectively, to investigate the effectiveness of reinforcement by hollow block and measured the magnitude of lateral movement, and compared with the limit value of 0.015h (Building Earthquake Code, 2019). Based on the results of shaking table test for hollow concrete block reinforced sandy ground, honeycell type hollow block gives a large interlocking force due to the filling of crushed stone in the hollow space as well as a great interface friction force by the confining pressure and punching resistance along the inside and outside of hollow concrete block. All these factors are contributed to reduce the great amount of horizontal displacement during the shaking table test. Finally, hollow concrete block reinforced sandy ground for shallow foundation is provided an outstanding reinforced method for medium-high building irrespective of seismic wave and moderate accelerations.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.1
• /
• pp.21-29
• /
• 2017

Surface soils on Barton Peninsula, King George Island, West Antarctica were investigated to acquire the mineralogical and geochemical data of soil in Antarctica. Multiline of techniques for example, X-ray diffraction (XRD), transmission electron microscopy (TEM)-electron energy loss spectroscopy (EELS), and wet chemistry analysis were performed to measure the composition of clay minerals, Fe-oxidation states, cation exchange capacity, and total cation concentration. Various minerals in sediments such as smectite, illite, chlorite, kaolinite, quartz and plagioclase were identified by XRD. Fe-oxidation states of bulk soils showed 20-40% of Fe(II) which would be ascribed to the reduction of Fe in clays as well as Fe-bearing minerals. Moreover, redox states of Fe in smectite structure was a ~57% of Fe(III) consistent to the values for the bulk soils. The cation exchange capacity of bulk soils ranged from 100 to 300 meq/kg and differences were not significantly measured for the sampling locations. Total cations (Mg, K, Na, Al, Fe) of bulk soils varies, contrast to the heavy metals (Co, Ni, Cu, Zn, Mn). These results suggested that composition of bed rocks influenced the distribution of elements in soil environments and soils containing clay compositions may went through the bio/geochemical alteration.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.1-13
• /
• 2019

The purpose of this study is to examine the effect of soft ground improvement by dynamic replacement with utilizing crushed rock. In order to understand the ground improvement effect when applying dynamic replacement method with crushed rock, the laboratory test and field test were performed. The internal friction angle and apparent cohesion were derived through direct shear test. The dynamic replacement characteristics were identified by analyzing the weight, drop, and number of blows needed for dynamic replacement. Through the field plate bearing test and density test, the bearing capacity and settlement of the improved ground were measured, and the numerical analysis were conducted to analyze the behavior of the improved ground. In this study, it proposes modified soil experimental coefficient(C_DR) to 0.3~0.5 in the dynamic replacement method with crushed rock. Also when applying the dynamic replacement method using crushed rock, the particle size range is less than 100 mm, D₉₀ is less than 80 mm and D₁₅ is more than 30 mm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8128-8139
• /
• 2015

Recently, the necessity of developing the load and resistance factor design(LRFD) for soft ground improvement method has been raised, since the limit state design is requested as international technical standard for the foundation of structures. In this study, to develop LRFD codes for foundation structures in Korea, target reliability index and resistance factor for static bearing capacity of driven steel pipe piles were calibrated in the framework of reliability theory. The 16 data(in Gwangyang) and the 57 data(Korea Institute of Construction Technology, 2008) sets of static load test and soil property tests conducted in the whole domestic area were collected along with available subsurface investigation results. The resistance bias factors were evaluated for the tow static design methods by comparing the representative measured bearing capacities with the expected design values. Reliability analysis was performed by two types of advanced methods : the First Order Reliability Method (FORM), and the Monte Carlo Simulation (MCS) method using resistance bias factor statistics. As a result, when target reliability indices of the driven pipe pile were selected as 2.0, 2.33, 2.5, resistance factor of two design methods for SPT N at pile tip less than 50 were evaluated as 0.611~0.684, 0.537~0.821 respectively, and STP N at pile tip more than 50 were evaluated as 0.545~0.608, 0.643~0.749 respectively. The result from this research will be useful for developing various foundations and soil structures under LRFD.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.413-427
• /
• 2013

Thin Spray-on Liners(TSLs) based on polymer materials have been considered as an alternative to shotcrete and wire mesh in relatively fair rock conditions, and used in mines since 1990s. Nevertheless, Few experimental studies on their mechanical properties necessary for the evaluation of their bearing capacities as a support member have been carried out. In this study, tensile and bond strengths of two kinds of TSLs with different material compositions were measured at the age of 7 days. In addition, two kinds of bending tests proposed by EFNARC (2008) to simulate representative failure mechanisms of TSLs were carried out on the same materials and curing age as in tension and pull-out tests. From the tests, tensile strength of a TSL is shown to increase as its content of polymer is higher. In contrast, its bond strength seems to be in inverse proportion to its polymer content. Especially, the TSL material in which a cementitious component is included with relatively smaller polymer content shows a faster hardening characteristic which results in higher resistance to de-bonding between a TSL and a substrate. As a result, it is shown that the performance of TSLs might be dependent upon its corresponding polymer content.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.12
• /
• pp.43-51
• /
• 2014

Organic matter in dredged soil has a lot of engineering problem in ground including a large settlement, crack propagation, low bearing capacity and low friction angle. From an agricultural point of view, however, organic matter contributes greatly soil quality and plant health. This paper investigated the relationship between engineering and germination characteristics of stabilized mixture consisting of different ratios of organic content (0 %, 10 %, 20 %, 30 %) for recycling dredged soil including organic matter. Several series of laboratory tests such as flow test, unconfined compressive test and consolidation test were performed to find out engineering characteristics. pH, percent of germination and growth of plants were also measured to investigate the germination characteristics. The experimental results indicated that, as organic content increased, unconfined compressive stress decreased and compression and swelling indices increased. However, percent of germination and plant growth increases as organic content increases.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.3-44
• /
• 1999

This paper discusses the lateral behavior of single and group piles in homogeneous and non-homogeneous(two layered) soil. In the single pile, the model tests were conducted to investigate the effects on ratio of lower layer height to embedded pile length, ratio of soil modules of upper layer to lower layer, boundary rendition of pile head and tip, embedded pile length, pile construction condition, ground condition with saturate and moisture state in Nak-Dong river sand. Also, in the group pile, the model tests were to investigate the effects on spacing-to-diameter ratio of pile, pile array, ratio of pile spacing, boundary condition of pile head and tip, eccentric load and ground condition. The maximum bending moment and deflection induced in active piles were found to be highly dependent on the relative density, pile construction condition, boundary condition of pile head and tip. Based on the results obtained, it was found that the decrease of lateral bearing capacity in saturated sand was in the range of 31% - 53% as compared with the case of dry sand. Also, in the group pile, a spacing-to-diameter of 6.0 seems to be large enough to eliminate the group effect for the case of relative density of 61.8%, and 32.8%, and then each pile in such a case behaves essentially the same as a single pile. In this study, the program is developed by using the modified Chang method which used p - y method and the exact solution of governing equation of pile and it can be used to calculate the deflection, bending moment and soil reaction with FDM in non-homogeneous soil. In comparing the modified Chang method with field test results, the predict results shows better agreement with measured results in field tests.

• Tunnel and Underground Space
• /
• v.11 no.2
• /
• pp.174-181
• /
• 2001

The cavities created by underground mining, if remained unfilled, can cause ground settlement and surface subsidence as a result of relaxation and breakdown of the carven roof. Construction of structures above the underground mine cavity will have serious problems concerning both structural stability and safely even if the cavity is back-filled. This study was conducted to confirm the location and condition of the cavern as well as the state of the back-fill in A mine area using core logging and borehole camera. The bearing capacity and other mechanical properties of the ground were also measured by the standard penetration test(SPT). Obtained data were used to assess the stability of the ground and the structures to be built by numerical analysis using FLAC. The site investigation results showed that the mine cavities were filled with materials such as boulder and silty sand(SM by unified classification). Result of the numerical analyses indicated that constructing building structures on the over-lying ground above the filled cavities is secure against the potential problems such as surface subsidence and ground settlement.

• Korean Journal of Acupuncture
• /
• v.25 no.3
• /
• pp.81-96
• /
• 2008

Objectives : The purpose of the present study is to determine the effective analgesic parameters of manual acupuncture (MA) and/or electroacupuncture (EA), thus how MA & EA of specific acupoint works after acute ankle sprain in rats. Thus, one series of experiments was designed to analyze the analgesic effects of acupuncture in either the normal or sprained rat, by comparing the behavioral features before and after MA or EA at several acupoints. Methods : Ankle sprain was induced manually by hyper-extension of ligaments of the right ankle in rat. Either MA or EA was applied to the LI4, TE17, 足三里 and SI-6 acupoints at an intensity of 2 mA (1 ms pulse duration) with a frequency of 10 Hz for 30 minutes. Results : Behaviorally, manual acupuncture or electroacupuncture produced potent analgesic effects on acute ankle sprained animals as measured by weight bearing capacity of the affected limb. Furthermore, antinociceptive effect of EA was suppressed by alpha adrenoceptor antagonist phentolamine (5 mg/kg, i.p.) but not by opioid antagonist naltrexone (10 mg/kg, i.p.). Conclusions : It is suggested that acupuncture-induced antinociception may involve the descending inhibition of ${\alpha}2$-adrenoceptor.

• Geomechanics and Engineering
• /
• v.27 no.6
• /
• pp.537-550
• /
• 2021

There are various technical problems need to be solved in the construction process of pre-setting an isolation wall into a double lane in the outburst prone mine. This study presents a methodology that pre-setting an isolation wall into a double lane without a coal pillar. This requires the excavation of two small section roadways to dig a wide section roadway, followed by construction of the separation wall. During this process the connecting lane is reserved. In order to ensure the stability of the separation wall, the required bearing capacity of the isolation wall is 4.66 MN/m and the deformation of the isolation wall is approximately 25 cm. To reduce the difficulty of implementing support the roadway is driven by 5 m/d. After the construction of the separation wall, the left side coal wall is brushed 1.5 m to make the width of the gas roadway reach 2.5 m and the roadway support utilizes anchor rod, ladder beam, anchor cable beam and net configuration. During construction, the concrete pump and removable self-propelled hydraulic wall mold are used to pump and pour the concrete of the isolation wall. In the process of mining, the stress distribution of coal body and isolation wall is detected and measured on site. The results demonstrate that the deformation of the surrounding rock of roadway and separation of roof in the roadway is small. The stress of the bolt and anchor cable is within equipment tolerance validating their selection. The roadway is well supported and the intended goal is achieved. The methodology can be used for reference for similar mine gas control.