• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.7C
• /
• pp.715-723
• /
• 2009

In this paper, we propose a new detection method called dual-cell combining (DCC) detection for the acquisition in time of spread spectrum codes in the presence of residual frequency offset (RFO). When the RFO exists, the correlation peak used for detection during the acquisition process is split into two neighboring peaks with smaller amplitudes, resulting in considerable degradation in the overall acquisition performance of conventional methods. In the DCC detection method, the decision variable for detection is formed by combining two consecutive correlator outputs so that the influence of the reduction in the correlation peak due to the RFO can be alleviated. Numerical results show that the DCC detection method can offer better mean-time-to-synchrouization performance than the conventional method based on the cell-by-cell detection.

• Safety and Health at Work
• /
• v.8 no.4
• /
• pp.364-370
• /
• 2017

Background: Labeled noise reduction (NR) data presented by manufacturers are considered one of the main challenging issues for occupational experts in employing hearing protection devices (HPDs). This study aimed to determine the actual NR data of typical HPDs using the objective fit testing method with a microphone in real ear (MIRE) method. Methods: Five available commercially earmuff protectors were investigated in 30 workers exposed to reference noise source according to the standard method, ISO 11904-1. Personal attenuation rating (PAR) of the earmuffs was measured based on the MIRE method using a noise dosimeter (SVANTEK, model SV102). Results: The results showed that means of PAR of the earmuffs are from 49% to 86% of the nominal NR rating. The PAR values of earmuffs when a typical eyewear was worn differed statistically (p < 0.05). It is revealed that a typical safety eyewear can reduce the mean of the PAR value by approximately 2.5 dB. The results also showed that measurements based on the MIRE method resulted in low variability. The variability in NR values between individuals, within individuals, and within earmuffs was not the statistically significant (p > 0.05). Conclusion: This study could provide local individual fit data. Ergonomic aspects of the earmuffs and different levels of users experience and awareness can be considered the main factors affecting individual fitting compared with the laboratory condition for acquiring the labeled NR data. Based on the obtained fit testing results, the field application of MIRE can be employed for complementary studies in real workstations while workers perform their regular work duties.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.5
• /
• pp.27-39
• /
• 2004

In the first part of this study, five homogeneous regions in view of topographical and geographically homogeneous aspects except Jeju and Ulreung islands in Korea were accomplished by K-means clustering method. A total of 57 rain gauges were used for the regional frequency analysis with minimum rainfall series for the consecutive durations. Generalized Extreme Value distribution was confirmed as an optimal one among applied distributions. Drought rainfalls following the return periods were estimated by at-site and regional frequency analysis using L-moments method. It was confirmed that the design drought rainfalls estimated by the regional frequency analysis were shown to be more appropriate than those by the at-site frequency analysis. In the second part of this study, LH-moment ratio diagram and the Kolmogorov-Smirnov test on the Gumbel (GUM), Generalized Extreme Value (GEV), Generalized Logistic (GLO) and Generalized Pareto (GPA) distributions were accomplished to get optimal probability distribution. Design drought rainfalls were estimated by both at-site and regional frequency analysis using LH-moments and GEV distribution, which was confirmed as an optimal one among applied distributions. Design rainfalls were estimated by at-site and regional frequency analysis using LH-moments, the observed and simulated data resulted from Monte Carlotechniques. Design drought rainfalls derived by regional frequency analysis using L1, L2, L3 and L4-moments (LH-moments) method have shown higher reliability than those of at-site frequency analysis in view of RRMSE (Relative Root-Mean-Square Error), RBIAS (Relative Bias) and RR (Relative Reduction) for the estimated design drought rainfalls. Relative efficiency were calculated for the judgment of relative merits and demerits for the design drought rainfalls derived by regional frequency analysis using L-moments and L1, L2, L3 and L4-moments applied in the first report and second report of this study, respectively. Consequently, design drought rainfalls derived by regional frequency analysis using L-moments were shown as more reliable than those using LH-moments. Finally, design drought rainfalls for the classified five homogeneous regions following the various consecutive durations were derived by regional frequency analysis using L-moments, which was confirmed as a more reliable method through this study. Maps for the design drought rainfalls for the classified five homogeneous regions following the various consecutive durations were accomplished by the method of inverse distance weight and Arc-View, which is one of GIS techniques.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.98-106
• /
• 2008

To reduce the outage probability and to increase the transmission capacity, the importance of repeaters in cellular systems keeps increasing. Unlike optical repeaters which require wireline connections, RF repeaters are easy to install, have low limitations in location and also have a reduced operational expense such as the optical fiber maintenance cost. On the other hand, RF repeaters suffer the interference due to the feedback signals between the transmitter and receiver antennas, hence require an extra interference cancellation method when the amount of the feedback signal reduction by using the shielding is not sufficient. In this paper, a channel estimation method for two-path feedback interference signals in the ICS (Interference Cancellation System) repeaters using baseband signal processing is proposed and its performance is evaluated. When compared with the conventional method which estimates each multipath individually, the proposed method achieves 10 dB performance gain in terms of the normalized mean-squared-error.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• Phonetics and Speech Sciences
• /
• v.6 no.1
• /
• pp.77-83
• /
• 2014

This paper proposes a speaker and environment clustering method in order to overcome the degradation of the speech recognition performance caused by various noise and speaker characteristics. In this paper, instead of using the distance between Gaussian mixture model (GMM) weight vectors as in the Google's approach, the distance between the adapted mean vectors based on the modified maximum a posteriori (MAP) adaptation is used as a distance measure for vector quantization (VQ) clustering. According to our experiments on the simulation data generated by adding noise to clean speech, the proposed clustering method yields error rate reduction of 10.6% compared with baseline speaker-independent (SI) model, which is slightly better performance than the Google's approach.

• Journal of the Korean Society of Safety
• /
• v.22 no.5
• /
• pp.41-49
• /
• 2007

In general, the curved structures have the engineering efficiency as well as a fine view compared with straight member. Also, composite materials are composed of two or more different materials to produce desirable properties for structural strength as compared to single ones. Shell structures with composite materials have many advantages in strength and weight reduction. Therefore, composite laminated conical shells are analyzed in this study. To solve differential equations of conical shells, this paper used finite difference method. Various parametric study according to the change of radius ratio, vertex angle and subtended angle are examined. The change of radius ratio, vertex angle and subtended angle mean the change from conical shells to cylindrical shells, conical shells to circular plates and open shells closed shells, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.198-206
• /
• 1999

An automobile outside rear view mirror system has been analyzed and designed to reduce vibration with a finite element model. model analysis is conducted for the calculation of natural frequencies. harmonic analysis is utilized to estimate the displacements of the glass surface under dynamic loads. The model is verified with the vibration experiment of the parts and the assembled body. The structure of the mirror system is optimized for the robustness defined by the Taguchi concept. At first, many potential design variables are defined. Final design variables are selected based on the amount of contribution on the objective function. That is, sensitive variables are chose. The SN ratio in the Taguchi method is replaced by an objective function with the mean and the standard deviation of the quality characteristic. The defined objective function is appropriate in the structural design in that the vibration displacements are minimized while the robustness is improved.

• Structural Engineering and Mechanics
• /
• v.32 no.1
• /
• pp.21-36
• /
• 2009

An importance sampling method is presented for computing the first passage probability of elasto-plastic structures under stochastic excitations. The importance sampling distribution corresponds to shifting the mean of the excitation to an 'adapted' stochastic process whose future is determined based on information only up to the present. A stochastic control approach is adopted for designing the adapted process. The optimal control law is determined by a control potential, which satisfies the Bellman's equation, a nonlinear partial differential equation on the response state-space. Numerical results for a single-degree-of freedom elasto-plastic structure shows that the proposed method leads to significant improvement in variance reduction over importance sampling using design points reported recently.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.10a
• /
• pp.11-18
• /
• 2004

In this paper, an efficient model reduction scheme is presented for large scale dynamic systems. The method is founded on a modal analysis in which optimal eigenvalue is extracted from time samples of the given system response. The techniques we discuss are based on classical theory such as the Karhunen-Loeve expansion. Only recently has it been applied to structural dynamics problems. It consists in obtaining a set of orthogonal eigenfunctions where the dynamics is to be projected. Practically, one constructs a spatial autocorrelation tensor and then performs its spectral decomposition. The resulting eigenfunctions will provide the required proper orthogonal modes(POMs) or empirical eigenmodes and the correspondent empirical eigenvalues (or proper orthogonal values, POVs) represent the mean energy contained in that projection. The purpose of this paper is to compare the reduced order model using Karhunen-Loeve expansion with the full model analysis. A cantilever beam and a simply supported plate subjected to sinusoidal force demonstrated the validity and efficiency of the reduced order technique by K-L method.