• 한국지반환경공학회 논문집
• /
• 제8권2호
• /
• pp.19-27
• /
• 2007

본 연구에서는 준설에 따른 점토사면의 변형 및 변위양상과 파괴형태를 평가하기 위하여 준설사면의 기울기를 변화시키면서 원심모형실험을 실시하였다. 준설사면의 기울기는 1:2, 1:2.5, 1:3으로 변화시키면서 모형실험을 수행하였다. 실험 결과 기울기 1:3인 경우에는 4개월 경과시점까지 사면부내에서 변위는 발생되었지만, 초기단면과 유사하게 사면을 유지하고 있어 준설후 사면 안정성의 확보에는 문제가 없는 것으로 평가되었다. 준설사면 기울기가 1:2.5인 경우에는 4개월 경과시점에서 사면부내에서 국부적인 사면파괴가 발생하였으며, 기울기가 1:2인 사면의 경우 경과시간 2개월 후 원호파괴형태의 사면내 파괴가 발생되었다. 실험결과 지반의 최대 연직변위는 사면의 비탈머리에서 발생하였으며, 최대 수평변위는 비탈머리를 기준으로 0.5~1H(H : 초기 점토층의 높이) 떨어진 지점의 사면부 아래에서 발생하였으며, 최대 수평변위는 최대연직변위의 약 2배 정도인 것으로 나타났다.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.35-61
• /
• 1978

동력경운깅가 일반 경사지에서 견인주행하는 경우 견인주행성능과 주행특성을 구명하기 위하여 토양의 종류 및 상태는 일정하게 하고 지면의 기하학적 조건과 견인주행속도 및 견인하중을 변수로 하여 외부동력전달계의 시점인 좌우차륜과 토양간에 발생하는 차륜구동력 및 굴름정항과 Engine에서 구동륜까지 내부전달계를 통하여 전달된 동력의 이론치와 실험치와의 부합여부를 검정하고 부가적으로 동력경운기가 경사지기계화의 동력기로써의 가능성여부와 문제점을 찾으려한다.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.34-34
• /
• 1978

동력경운깅가 일반 경사지에서 견인주행하는 경우 견인주행성능과 주행특성을 구명하기 위하여 토양의 종류 및 상태는 일정하게 하고 지면의 기하학적 조건과 견인주행속도 및 견인하중을 변수로 하여 외부동력전달계의 시점인 좌우차륜과 토양간에 발생하는 차륜구동력 및 굴름정항과 Engine에서 구동륜까지 내부전달계를 통하여 전달된 동력의 이론치와 실험치와의 부합여부를 검정하고 부가적으로 동력경운기가 경사지기계화의 동력기로써의 가능성여부와 문제점을 찾으려한다.

• 터널과지하공간
• /
• 제6권2호
• /
• pp.166-174
• /
• 1996

Stability of rock slope is greatly affected by the geometry and strength of discontinuities developed in the rock mass. In this study an analytical method which is capable of analyzing the effect of relative orientation between the discontinuities and the slope face on the safety of slope by assessing their vector components was used to evaluate the stability and the maximum cut-angle for the proposed slope design. The results of computerized vector analysis revealed that slope area under investigation might be divided into 3 sections of different face directions. The safety factors for benches in each 3 sections were calculated using the limit-equilibrium theory. Then, by utilizing the concept of probabilistic risk analysis, the susceptibility of entire slope failure was estimated. Based on the distribution of safety factor in each bench, the maximum cut angle of each section could be selected differently ot achieve the permanent stability of the entire slope.

• Geomechanics and Engineering
• /
• 제6권6호
• /
• pp.561-575
• /
• 2014

Estimating seismic displacements has a great importance for foundations on or adjacent to slope surfaces. However, dynamic solution of the problem has received little attention by previous researchers. This paper presents a new analytical model to determine seismic displacements of the shallow foundations adjacent to slopes. For this purpose, a dynamic equilibrium equation is written for the foundation with failure wedge. Stiffness and damping at the sliding surface are considered variable and a simple method is proposed for its estimation. Finally, for different failure surfaces, the calculated dynamic displacement and the surfaces with maximum strain are selected as the critical failure surface. Analysis results are presented as curves for different slope angles and different foundation distances from edge of the slope and are then compared with the experimental studies and software results. The comparison shows that the proposed model is capable of estimating seismic displacement of the shallow foundations adjacent to slopes. Also, the results demonstrate that, with increased slope angle and decreased foundation distances from the slope edge, seismic displacement increases in a non-linear trend. With increasing the slope angle and failure wedge angle, maximum strain of failure wedge increases. In addition, effect of slope on foundation settlement could be neglected for the foundation distances over 3B to 5B.

• 설비공학논문집
• /
• 제23권7호
• /
• pp.492-497
• /
• 2011

The objective of this research is to study the variation of optimum slope angles of collectors for seven regions in Korea, which are Seoul, Gangneung, Daejeon, Daegu, Gwangju, Busan and Jeju. The results for 2000~2007 are analyzed to sec if adjustment of slope angles is necessary each year to receive maximum solar radiation. For an azimuth fixed solar collector, solar radiation of yearly optimized slope angle during May~Sept.(summer), Nov.~Mar.(winter) and the whole year are greater than the fixed slope angle by 0.03%, 0.02%, and 0.04%, respectively. For an azimuth tracking solar collector, solar radiation of yearly optimized slope angle during May~Sept.(slimmer), Nov.-Mar.(winter) and the whole year are greater than the fixed slope angle by 0.03%, 0.07%, and 0.04% respectively. It is unnecessary to adjust slope angles each year for both azimuth fixed and tracking collectors, since the gains are insignificant. Solar radiation of the azimuth tracking solar collector during May~Sept., Nov.~Mar. and the whole year are greater by 14.7%, 16.0%, and 19.2% than the azimuth fixed solar collector.

• 한국지리정보학회지
• /
• 제8권3호
• /
• pp.121-128
• /
• 2005

산불은 지형인자 중 경사에 의하여 대형화되는 경향이 강하다. 이러한 경사는 보통 GIS를 이용하여 분석하게 되는데 어떠한 분석 방법을 사용하는가에 따라 결과가 다르게 나타난다. 따라서 산불확대위험 분석에 합당한 경사 분석 방법을 선택하는 것이 중요하다. 본 연구에서는 셀기반 모델링을 이용하여 기존에 DEM 자료를 이용하여 경사를 계산하는 방법들을 검토하고, 산불확대위험 분석에 적합한 경사계산 알고리즘을 개발하고자 하였다. 그 결과 산불이 상향사면을 따라 급속하게 번지는 특성을 이용하여 산불확대위험 분석에 가장 적합한 경사계산 알고리즘으로 maximum uphill slope 알고리즘을 개발하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제19권3호
• /
• pp.39-46
• /
• 2022

In South Korea, to evaluate the rollover safety of domestic vehicles, the maximum slope angle of the vehicle is specified, which is verified by the rollover safety test of driving vehicles. However, the domestic rollover safety test is not suitable for buses, because the small amount of static stability factor (SSF) will invalidate the rollover experimental equation due to the high center of mass position of buses. To solve the above problems, a dynamic model of the bus is prepared with assumptions of mass and suspension spring properties. Subsequently, the maximum slope angle of the model was computed by using the simulation of multi-body dynamics, and the result was compared with actual test results to validate the dynamics model. Also, the rollover Fishhook (roll stability) test was conducted in the simulation for driving model. During the simulation, roll angle and roll rate were calculated to check if a rollover occurred. Through the rollover simulation of buses, the domestically regulated formula for rollover safety and the procedure of rollover test for driving vehicles are evaluated. The conclusion is that the present regulation of rollover test should be reconsidered for buses to ensure to get the valid results for rollover safety.

• 산업기술연구
• /
• 제22권A호
• /
• pp.153-159
• /
• 2002

This paper is an experimental work of estimating friction angle of very coarse grained soil such as rubble mound by performing laboratory experiments. Two crushed rocks of rubble mound were used for tests. Triaxial compression tests with drained conditions were performed to measure friction angles of soils prepared by mixing the crushed soil having an identical coefficient of uniformity with different maximum grain size distribution. Centrifuge model experiments with those soils were also performed to measure angle of repose and to estimate friction angle of soil from measuring the slope of slip line in the active stress state. Model tests were carried out by changing the G-levels of 1G and 50G. From triaxial compression tests, the measured value of friction angle of soil is in the range of $41{\sim}57^{\circ}$. The measured value of repose angle is in the range of $32{\sim}35^{\circ}$. The values of friction angle are found not so sensitive to the maximum grain size of soil as long as the coefficient of uniformity is identical. Estimated value of friction angle from measuring the slope of slip line in the active stress state is in the range of $30{\sim}46^{\circ}$. Thus, the estimated angle of friction are found to be greater in the order of the measured angle of repose, the estimated value from the slope of active state, and triaxial compression test results. On the other hand, the measured values of friction angle from triaxial tests were compared with empirical equations, based on the relation between friction angle and void ratio. Equations proposed by Helenelund(l966) and Hansen(1967) found to be relatively reliable to estimate friction angles of soil.

• 한국태양에너지학회 논문집
• /
• 제32권2호
• /
• pp.64-73
• /
• 2012

The angle of solar panels is calculated using solar radiation model for the efficient solar power generation. In ideal state, the time of maximum solar radiation is represented from 12:08 to 12:40 during a year at Gangneung and it save rage time is12:23. The maximum solar radiation is 1012$W/m^2$ and 708$W/m^2$ inc lear sky and cloudy sky, respectively. Solar radiation is more sensitive to North-South (N-S) slope angle than East-West (E-W) azimuth angle. Daily solar radiation on optimum angle of solar panel is higher than that on horizontal surface except for 90 days during summer. In order to apply to the real atmosphere, the TMY (typical meteorological Year) data which obtained from the 22 solar sites operated by KMA(Korea Meteorological Administration) during 11 years(2000 to 2010) is used as the input data of solar radiation model. The distribution of calculated solar radiation is similar to the observation, except in Andong, where it is overestimated, and in Mokpo and Heuksando, where it is underestimated. Statistical analysis is performed on calculated and observed monthly solar radiation on horizontal surface, and the calculation is overestimated from the observation. Correlationis 0.95 and RMSE (Root Mean Square Error) is10.81 MJ. The result shows that optimum N-S slope angles of solar panel are about $2^{\circ}$ lower than station latitude, but E-W slope angles are lower than ${\pm}1^{\circ}$. There are three types of solar panels: horizontal, fixed with optimum slope angle, and panels with tracker system. The energy efficiencies are on average 20% higher on fixed solar panel and 60% higher on tracker solar panel than compared to the horizontal solar panel, respectively.