• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.52-56
• /
• 2011

Active regeneration in CDPF requires $O_2$ which regenerates soot at high temperature. However, small amount of NO can interrupt $O_2$ regeneration in CDPF. To verify this phenomena, soot oxidation experiments using a flow reactor with a $Pr/CeO_2$ catalyst are carried out to simulate Catalyzed Diesel Particulate Filter (CDPF) phenomena. Catalytic soot oxidation with and without small amount of NO is conducted under tight contact condition. As the heating rate rises, the temperature gap of maximum reaction rate is increased between with and without 50ppm NO. To accelerate the $NO_2$ de-coupling effect, CTO process is performed to eliminate interfacial contact for that time. As CTO process is extended, temperature which indicates peak reaction rate increases. From this result, it is found that small amount of NO can affect tight contact soot oxidation by removal of interfacial contact between soot and catalyst.

• Geomechanics and Engineering
• /
• 제4권4호
• /
• pp.281-294
• /
• 2012

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.

• 생물환경조절학회지
• /
• 제23권1호
• /
• pp.39-42
• /
• 2014

본 연구의 목적은 선형, 쌍곡선, 베타 함수를 이용하여 상추의 주요 온도를 예측하기 위함이다. 상추 종자를 항온 생육상에서 발아시켰다. 온도처리는 $10^{\circ}C$, $14^{\circ}C$, $16^{\circ}C$, $20^{\circ}C$, $24^{\circ}C$, $28^{\circ}C$와 $32^{\circ}C$였다. 100개의 종자를 9cm 페트리디쉬에 필터페이퍼 2장을 깔고 4반복 실시하였다. 유근이 1mm 나왔을 때를 발아로 하였다. 시간에 따른 발아율은 로지스틱 함수로 계산하였다. 최저, 최적, 최고 온도는 50% 발아한 시점의 역수를 온도에 따른 함수로 표기하여 나타내었다. 선형 함수의 경우, 최저, 최적, 최고 온도는 각각 $7.9^{\circ}C$, $23.3^{\circ}C$, $28.0^{\circ}C$였으며, 쌍곡선 함수의 경우, 최저, 최적, 최고 온도는 각각 $9.7^{\circ}C$, $19.5^{\circ}C$, $29.4^{\circ}C$였으며, 베타 함수인 경우, 최저, 최적, 최고 온도는 각각 $3.7^{\circ}C$, $20.7^{\circ}C$, $32.0^{\circ}C$였다. 최저, 최적, 최고 온도 범위는 각각 $3.7{\sim}7.9^{\circ}C$, $19.5{\sim}23.3^{\circ}C$, $28.0{\sim}32.0^{\circ}C$이었다.

• Journal of Microbiology and Biotechnology
• /
• 제14권6호
• /
• pp.1196-1199
• /
• 2004

A bacterium, isolated from rabbit's waste and identified as Cellulomonas sp., had cellulase and thermostable $\alpha$-amylase activity when grown on wheat bran. Maximum activity of thermostable $\alpha$-amylase was obtained by adding $3\%$ soluble starch. However, soybean oil (1 ml $1^{-1}$) could increase the production of $\alpha$-amylase and cellulase in 'wheat bran. The $\alpha$-amylase was characterized by making a . demonstration of optimum activity at $90^{\circ}C$ and pH 6- 9, with soluble starch as a substrate. The effect of ions on the activity and the stability of this enzyme were investigated. This strain secreted carboxymethyl cellulase (CMCase), cellobiase ($\beta$­glucosidase), and filter paperase (Fpase) during growth on wheat bran. Carboxymethy1cellulase, cellobiase, and Fpase activities had pH optima of 6, 5.5, and 6, respectively. CMCase and cellobiase activities both had an optimum temperature of $50^{\circ}C$, whereas Fpase had an optimum temperature of $45^{\circ}C$.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제12C권4호
• /
• pp.220-224
• /
• 2002

The electromagnetic properties and thermal behavior of Mn-Zn ferrite cores for the blocking filter of PLC application were investigated as the function of additives. The highest density and permeability were 4.98 g/㎤ and 8,221, respectively and were obtained to the specimen with composition of MnO 24 mol%, ZnO 25 mol% and Fe$_2$O$_3$51 mol%, added MoO$_3$ of 400 ppm, SiO$_2$ of 100 ppm, and CaO of 200 ppm. The uniform grains were organized, and the microstructures were compacted due to reduction of pores in the specimen. The permeability was increased up to 13,904 as the temperature of specimen increased to 110。C. However, it was decreased precipitously under 100 over 110。C. The exothermic behavior was observed in the frequency range from 1 kHz to 1 MHz, and the maximum temperature of specimen was 102。C at 1 MHz. In the consequence, the Mn-Zn ferrite core developed in this research will maintain the stable electromagnetic properties since the temperature of ferrite core rose to 93 。C in the range of 100 kHz to 450 kHz bandwidth qualified for PLC. The blocking filters were designed for single phase and three phases using the in-line and non-contact core. The best attenuation ratios of -46.46 dB and -73.9 dB were measured in the range of 100 kHz to 450 kHz bandwidth, respectively.

• 접착 및 계면
• /
• 제10권3호
• /
• pp.141-147
• /
• 2009

본 연구는 web spray 분사방식으로 핫멜트 접착제를 이용하여 high performance hybrid chemical filter (HPHCF)를 제조하였다. HPHCF은 이온교환 수지와 PP 부직포를 사용하였고, HPHCF의 제조 시 최적 조건은 핫멜트의 온도는 $170^{\circ}C$에서 분사압력은 50 psi일 때 최적의 제조 조건을 나타내었다. 제조된 HPHCF의 특성 및 암모니아 흡착성능을 측정하였다. HPHCF 이온교환용량은 수지 부착량이 증가함에 따라 증가하였으며 단일 수지와 이온교환섬유의 이온교환용량보다 크게 나타났다. 또한 암모니아의 제거율은 HPHCF의 충진 밀도가 증가할수록 증가하였으며 흡착 파과시간은 13 min으로 단일 섬유나 수지에 비해 길게 나타났고 최대 암모니아 흡착량은 98%이었다. 또한 암모니아 흡착 파과시간은 유량 및 농도가 증가함에 따라 빠르게 진행되었다.

• 대한전자공학회논문지SD
• /
• 제40권3호
• /
• pp.1-9
• /
• 2003

본 연구에서는 1-단자 표면탄성파 공진기를 적용한 사다리형 구조 필터에 대한 전극 두께, 공진기의 반사기 하중 및 정적 정전용량비에 따른 주파수 응답특성의 고찰이 이루어졌으며, 최적화된 매개변수를 이용하여 송신 및 수신단용 RF 필터를 제작하였다. 제작된 필터는 800㎒ 대역 이동통신 시스템에 적용 가능하며, 외부회로에 의한 임피던스 정합이 필요하지 않다. 36°LiTaO₃ 압전기판 위에 Al-Cu(W 3%) 전극을 형성하여 제작하였으며, 3.8㎜×3.8㎜×1.5㎜세라믹 패키지에 실장되었다. 통과대역(25 ㎒)에서의 최소 삽입손실은 2.3 dB, 3-dB 대역폭은 약 33 ㎒, 통과대역 리플은 0.5 dB 미만이며, 약 30 dB 이상의 저지대역 감쇄를 확보할 수 있었다. 또한, 제작된 RF 필터의 내전력성 및 온도 변화에 따른 주파수 응답특성 실험을 통해 약 3.5 W의 내전력성과 -20℃∼80℃에서 최대 0.09 dB/℃의 3-dB 삽입손실 변화를 측정할 수 있었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1244-1247
• /
• 2004

For obtaining the best panel quality of color filter on array(COA) architecture in TFF LCD, we investigated the influence of deposition temperature, $O_2$ flow, thickness on the optical transmittance, wet etching and adhesion properties of IZO deposited onto each color photo resist(red, green, blue). Average transmittance of the pixel single layer in the visible range(between 380 and 780nm) was mainly affected by thickness and showed maximum at 1250 ${\AA}$ while the thickness showing peak transparency in each R, G, B wavelength was different. The relation was calculated by using bi-layer transmission and reflectance model, which corresponded to experimental data very well. The adhesion of IZO deposited on each color PR was found to have enhanced value except red PR case, compared to that of IZO which was deposited on $SiN_x$. Wet etching pattern linearity was decreased as the thickness increased. The thickness of IZO was one of vital factors in order to optimize overall pixel process for fabricating COA structure.

• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.124-129
• /
• 2010

The direct injection (DI) diesel engine has become a prime candidate for future transportation needs because of its high thermal efficiency. However, nitrogen oxides (NOx) increase in the local high temperature regions and particulate matter (PM) increases in the diffusion flame region within diesel combustion. Therefore, the demand for developing hybrid system consist of exhaust gas recirculation (EGR) and aftertreatment system as well as diesel particulate filter (DPF) or lean NOx trap (LNT) should be applied. The variation of EGR rate due to the malfunction of EGR valve can affect not only the combustion stability of engine but also the performance of aftertreatment system. In this research, 2.0 liter 4-cylinder turbocharged diesel engine was used to investigate the combustion and emission characteristics for various operating conditions with EGR. While the fuel consumption was increased with increase of EGR rate, NOx emission was improved by maximum 90% at low speed, low load operating condition. To achieve combustion stability and reliability of aftertrearment system with minimum penalty in fuel consumption and emissions, the fault diagnosis of EGR malfunction must be employed.

• 대한환경공학회지
• /
• 제37권7호
• /
• pp.418-425
• /
• 2015

본 논문에서는 양돈폐수의 전처리 공정으로 부유성 세라믹 담체로 충진한 Anaerobic Filter (AF)을 이용하여 신재생에너지 메탄가스의 생산 가능성과 전처리 후 유출수의 후속 고도처리 적정성을 평가하였다. 유입 COD 농도가 14,000 mg/L인 양돈폐수를 Anaerobic Filter에 점진적으로 유기물부하(OLR)를 증가시키면서 혹은 수리학적 체류시간을 짧게 유지하면서 $35^{\circ}C$에서 운전한 결과는 다음과 같다. Anaerobic Filter는 HRT 0.5일(OLR 28 g TVS/L-d)에서 최대 메탄발생량 1.74 v/v-d를 달성하였으며, Biogas 기준 TVS 제거효율은 HRT 3일(OLR 4.67 g TVS/L-d)로 운전하였을 때 63%를 얻었다. 반면 유출수 분석에 의한 TCOD 제거효율은 75%를 상회하였다. 유출수의 알카리도는 모든 운전 조건에서 2,050~2,980 mg/L as $CaCO_3$로서 후속 질소제거 시 야기될 수 있는 알카리도 파괴를 상쇄할 수 있을 것이다. HRT 2일 이하의 운전조건에서 Anaerobic Filter 유출수의 COD/TKN 비는 10~35 범위로서 고도처리 시 적정비인 8 이상을 만족하였으며 COD/TP 비는 38~56범위로서 적정비 33 이상 유지가 가능하였다.