• KSBB Journal
• /
• v.31 no.1
• /
• pp.20-26
• /
• 2016

This study aims to examine the optimum blanching conditions as a pretreatment condition to improve the storage stability of Dolsan leaf mustard pickle. The effects of the blan- ching temperature and time were investigated at a temperature range of $80-100^{\circ}C$. Sampling was done for 1 month after a 5 days interval. The L value of the Dolsan leaf mustard was found to be the highest at $80^{\circ}C$. The cutting force increased as the blanching temperature increased. The tensile strength decreased at $95^{\circ}C$ and $100^{\circ}C$. In addition, the sensory evaluation scores were the best at $80^{\circ}C$. The storage stability was assessed at various blanching temperatures to increase the sinigrin content during storage. Liquid chromatography with photodiode array and tandem mass spectrometry (LC-PDA/MS/MS) analysis was conducted to identify and quantify the sinigrin content in the Dolsan leaf mustard. Sinigrin as an internal standard was co-injected into each sample solution. The sample was monitored by recording the ultraviolet absorbance at 228 nm and by electrospray ionization (ESI) positive ion mode in the m/z 50-1,500 range. Blanching the sample at $80^{\circ}C$ showed the highest sinigrin concentration during storage among various temperatures and the maximum concentration was 350 ppm at 15 days storage. Study on utilization of vegetable from food processing of leaf mustard and preservation conservation results suggest that blanching at $80^{\circ}C$ is expected to improve the palatability of the pickle.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.171-177
• /
• 2006

This study was performed as a part of the research on the development of a maskless and electroless process for fabricating metal micro/nanostructures by using a nanoindenter and an electroless deposition technique. $2-{\mu}m$-deep indentation tests on Ni and Cu samples were performed. The elastic recovery of the Ni and Cu was 9.30% and 9.53% of the maximum penetration depth, respectively. The hardness and the elastic modulus were 1.56 GPa and 120 GPa for Ni and 1.51 GPa and 104 GPa for Cu. The effect of single-point diamond machining conditions such as the Berkovich tip orientation (0, 45, and $90^{\circ}$ ) and the normal load (0.1, 0.3, 0.5, 1, 3, and 5 mN), on both the deformation behavior and the morphology of cutting traces (such as width and depth) was investigated by constant-load scratch tests. The tip orientation had a significant influence on the coefficient of friction, which varied from 0.52-0.66 for Ni and from 0.46- 0.61 for Cu. The crisscross-pattern sample showed that the tip orientation strongly affects the surface quality of the machined are a during scratching. A selective deposition of Cu at the pit-like defect on a p-type Si(111) surface was also investigated. Preferential deposition of the Cu occurred at the surface defect sites of silicon wafers, indicating that those defect sites act as active sites for the deposition reaction. The shape of the Cu-deposited area was almost the same as that of the residual stress field.

• Korean journal of food and cookery science
• /
• v.20 no.1
• /
• pp.86-94
• /
• 2004

The purpose of this study was to investigate the changes of hardness and microstructure of Dongchimi cooked with various source of water(distilled water, purified water, Cho Jung Carbonated Natural water). This study was conducted to observe the changes of pH, total acidity, salt content, turbidity, texture and microstructure. Dongchimi cooked with source of water of water was fermented at 10$^{\circ}C$ for 46 days. The changes of pH on Dongchimi cooked with various source of water decreased in all samples during fermentation period, and then showed a slowly decrease after 12 days of fermentation. The total acidity of Dongchimi cooked with Cho Jung Carbonated Natural water was arrived slowly at best tasting condition 0.3 ∼ 0.4 point compared with other conditions. So Dongchimi cooked with Cho Jung Carbonated Natural water was continued to the best tasting condition for end of fermentation. At early stage of fermentation, the changes of turbidity of Dongchimi used Cho Jung Carbonated Natural water showed highly as compared with other test condition for 12th days of fermentation. The maximum cutting force of chinese radish of Dongchimi showed the highest value among all at the 25th day of ripening and then decreased gradually. The maximum cutting force of chinese radish of Dongchimi used Cho Jung Carbonated Natural water was the highest compared with other conditions at 25th day of fermentation. The calcium content of Dongchimi juice used Cho Jung Carbonated Natural water was observed hish at the early stage of fermentation and showed the highest value at 25th day of ripening. The calcium content of chinese radish and Dongchimi juice of Dongchimi cooked with water purifier was lower than that of Dongchimi cooked with Cho Jung Carbonated Natural water, and was higher than that of Dongchimi cooked with Distilled water at the early stage of fermentation. The magnesium content in all samples increased gradually from the early stage of fermentation. The microstructure showed disintegration appearance of middle lamella and cell wall during fermentation period.

• Journal of Bio-Environment Control
• /
• v.22 no.3
• /
• pp.284-290
• /
• 2013

This study analyzed the geometric, compressive, cutting and friction properties of oriental melons in order to design a gripper capable of soft handling and a cutter for cutting oriental melon vine among the end effector of oriental melon as a preliminary step for developing the end effector of the robot capable of harvesting oriental melons in protected cultivation. As a result, the average length, diameter at the midpoint, weight, volume and roundness of the oriental melons were 108 mm, 70 mm, 188 g, 333 mL and 3.8 mm. Nonlinear regression analysis was performed on the equation $W=L^a{\times}D_2^b$ with variation of the length (L) and diameter (D2) of the weight (W) of the oriental melons. As a result, it was shown that there was a correlation between a of 2.0279 and b of -0.9998 as a constant value. The average diameter of the oriental melon vine was 3.8 mm, and most vines were distributed within a radius of 5 mm from the center. The average yield value, compressive strength and hardness of the oriental melons were $36.5N/cm^2$, $185.7N/cm^2$ and $636.7N/cm^2$, respectively. The average cutting force and shear strength of the oriental melon vines were $2.87{\times}10^{-2}\;N$ and $5.60N/cm^2$, respectively. The maximum friction coefficient of the oriental melons was rubber of 0.609, followed by aluminium of 0.393, stainless steel of 0.177 and teflon of 0.079. It was considered possible to apply it to the size of the gripper and cutter, turning radius, dynamics of drive motor and selection of materials and their quality in light of the position error and safety factor according to the movement when designing end effector based on the analyzed data.

• Korean Journal of Food Science and Technology
• /
• v.29 no.1
• /
• pp.44-50
• /
• 1997

Comparative study was performed on noodle characteristics among three domestic wheat varieties (Geurumil, Eunpamil and Alchanmil) and imported one (ASW: Australian Standard White). For the noodle-related characteristics, crude protein, ash and gluten contents were measured, and rheological properties of dough, flour color difference, particle size distribution, cooking properties and sensory properties were evaluated. Crude protein content of Geurumil, Eunpamil and Alchanmil flour were 12.8%, 14.2% and 11.2%, respectively, whereas that of ASW flours was 9.1%. Ash content was the highest in Geurumil (0.56%). The yield of patent flour was the highest in Eunpamil (53.4%) among all the varieties. Higher dough stability with farinogram and maximum viscosity with amylogram were shown in Eunpamil and Alchanmil than those of ASW. The cutting force of cooked noodle from ASW was the lowest maximum, that was measured by texture analyzer. Fairly good color and sensory scores were obtained in cooked noodle of Alchanmil. Studies of noodle-related characteristics indicated that domestic Eunpamil was higher in protein content and flour yield, and Alchanmil was higher dough stability and color, when compared to those of imported ASW. Alchanmil and ASW had good scores in sensory evaluation, especially appearance and color.