• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2017년)
• /
• pp.194-203
• /
• 2017

The center of percussion(COP) is the point of an extended massive object attached to a pivot where a perpendicular impact will produce no reactive shock at the pivot. COP is an important concept in the field of vibration and dynamics. In vibration, COP causes reduction of vibration and in dynamics, it brings about maximum speed of an object. Many studies about COP are still in progress. However most of the researches have typically focused on the method of mathematical and numerical anlalysis. In this paper, impact analysis was proved by the mechanical energy method using EDISON co-rotational plane beam transient analysis program. The result expressed in acceleration was the relative magnitude of the impulse, which was the indicator of COP. Then, these results were compared with the reference thesis results for exact consequences. Additionally, parametric study of COP was conducted.

• Structural Engineering and Mechanics
• /
• 제29권5호
• /
• pp.505-530
• /
• 2008

This paper proposes the application of active multiple tuned mass dampers (AMTMD) for translational and torsional response control of a simplified two-degree-of-freedom (2DOF) structure, able to represent the dynamic characteristics of general asymmetric structures, under the ground acceleration. This 2DOF structure is a generalized 2DOF system of an asymmetric structure with predominant translational and torsional responses under earthquake excitations using the mode reduced-order method. Depending on the ratio of the torsional to the translational eigenfrequency, i.e. the torsional to translational frequency ratio (TTFR), of asymmetric structures, the following three cases can be distinguished: (1) torsionally flexible structures (TTFR < 1.0), (2) torsionally intermediate stiff structures (TTFR = 1.0), and (3) torsionally stiff structures (TTFR > 1.0). The even distribution of the AMTMD within the whole width and half width of the asymmetric structure, thus leading to three cases of installing the AMTMD (referred to as the AMTMD of case 1, AMTMD of case 2, AMTMD of case 3, respectively), is taken into account. In the present study, the criterion for searching the optimum parameters of the AMTMD is defined as the minimization of the minimum values of the maximum translational and torsional displacement dynamic magnification factors (DMF) of an asymmetric structure with the AMTMD. The criterion used for assessing the effectiveness of the AMTMD is selected as the ratio of the minimization of the minimum values of the maximum translational and torsional displacement DMF of the asymmetric structure with the AMTMD to the maximum translational and torsional displacement DMF of the asymmetric structure without the AMTMD. By resorting to these two criteria, a careful examination of the effects of the normalized eccentricity ratio (NER) on the effectiveness and robustness of the AMTMD are carried out in the mitigation of both the translational and torsional responses of the asymmetric structure. Likewise, the effectiveness of a single ATMD with the optimum positions is presented and compared with that of the AMTMD.

• 한국터널지하공간학회 논문집
• /
• 제22권4호
• /
• pp.337-346
• /
• 2020

도심권의 교통 집중과 정체로 인하여 지하 공간 활용성이 필요함에 따라 지하구조물에 대한 연구가 늘어나고 있다. 그 중 복층터널은 지하구조물을 대표 할 수 있다. 복층터널은 중간슬래브를 기준으로 상, 하부 차도를 구분하여 운영하고 있다. 중간슬래브는 차량의 하중 및 지진하중에 의하여 동적거동을 한다. 특히 지진의 의한 응답특성은 하중의 크기 및 작용 메커니즘이 매우 복잡하고 이론적 접근이 어려워 실험적 연구가 필요하다. 본 연구에서는 붕괴방지 내진 1등급의 복층터널 중간슬래브에 진동 감쇠 고무받침 유무에 따른 안정성 평가를 실시하는데 목적을 두고 있다. 본 진동대 실험에서는 상사율 1/4을 적용하였으며, 모형실험에서 지반과 모형의 일체거동을 묘사하기 위하여 라이닝과 진동대판을 고정시켰으며 이를 통해서 상대거동을 최소화 하였다. 실험대상은 가상복층터널 TBM 표준단면으로 정했다. 기반암에 가해지는 지반운동 수준을 0.154 g (붕괴방지 수준 내진 1등급 인공지진파)이며 이 가속도를 최대로 하는 지진파를 진동대 입력(기반암)에 작용시켜 모형에 증폭현상을 분석하고 진동 감쇠 고무받침 유무에 따른 중간슬래브의 내진 안정성에 대해 평가 분석 하였다. 그 결과, 지진 감쇠 고무받침 유무에 따라서 지진 가속도 감쇠 효과가 최대 40% 이상 있음을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제27권4호
• /
• pp.223-230
• /
• 2014

본 논문에서는 FSI해석을 이용하여 비정형 초고층 빌딩의 풍응답 특성을 연구하였다. 해석모델은 Twist모델이며, 뒤틀림 각도와 풍가속도의 상관관계에 대해 연구 중점을 두었다. 먼저 단방향 해석을 수행하여 100년 재현주기 풍속에 대한 최대 횡 변위를 구하고, 제한조건을 만족하는 탄성계수를 산출한다. 그리고 양방향 해석을 수행, 시간이력해석을 통해 산출된 탄성계수와 임의의 밀도를 가지는 풍가속도를 예측하게 된다. 정방형 모델은 높이 400m, 변장비 1:1, 세장비 8로 설정, 뒤틀림 모델은 0도에서 90도까지 15도 간격으로, 90도에서 360도까지 90도 간격으로 비틀어 회전시켰다. 형상에 따른 풍가속도 예측 결과, 정방형 모델이 뒤틀림 모델보다 크게 산출되어 풍진동 영향에 더 민감한 것을 검증하였다.

• Smart Structures and Systems
• /
• 제16권4호
• /
• pp.579-591
• /
• 2015

This paper investigates a magnetoelectric (ME) vibration energy harvester that can scavenge energy in arbitrary directions in a plane as well as wide working bandwidth. In this harvester, a circular cross-section cantilever rod is adopted to extract the external vibration energy due to the capability of it's free end oscillating in arbitrary in-plane directions. And permanent magnets are fixed to the free end of the cantilever rod, causing it to experience a non-linear force as it moves with respect to stationary ME transducers and magnets. The magnetically coupled cantilever rod exhibits a nonlinear and two-mode motion, and responds to vibration over a much broader frequency range than a standard cantilever. The effects of the magnetic field distribution and the magnetic force on the harvester's voltage response are investigated with the aim to obtain the optimal vibration energy harvesting performances. A prototype harvester was fabricated and experimentally tested, and the experimental results verified that the harvester can extract energy from arbitrary in-plane directions, and had maximum bandwidth of 5.5 Hz, and output power of 0.13 mW at an acceleration of 0.6 g (with $g=9.8ms^{-2}$).

• Geomechanics and Engineering
• /
• 제20권2호
• /
• pp.103-112
• /
• 2020

The dynamic response of crossing tunnels under heavy-haul train loads is still not fully understood. In this study, based on the case of a high-speed tunnel underneath an existing heavy-haul railway tunnel, a model experiment was performed to research the dynamic response characteristics of crossing tunnels. It is found that the under-crossing changes the dynamic response of the existing tunnel and surrounding rock. The acceleration response of the existing tunnel enhances, and the dynamic stress of rock mass between crossing tunnels decreases after the excavation. Both tunneling and the excitation of heavy-haul train loads stretch the tunnel base, and the maximum tensile strain is 18.35 µε in this model test. Then, the measured results were validated by numerical simulation. Also, a parametric study was performed to discuss the influence of the relative position between crossing tunnels and the advanced support on the dynamic behavior of the existing tunnel, where an amplifying coefficient of tunnel vibration was introduced to describe the change in acceleration due to tunneling. These results reveal the dynamic amplifying phenomenon of the existing tunnel during the new tunnel construction, which can be referred in the dynamic design of crossing tunnels.

• Earthquakes and Structures
• /
• 제16권2호
• /
• pp.149-163
• /
• 2019

By integrating an active tuned mass damper (ATMD) and an inerter, the ATMDI has been proposed to attenuate undesirable oscillations of structures under the ground acceleration. Employing the mode generalized system, the dynamic magnification factors (DMF) of the structure-ATMDI system are formulated. The criterion can then be defined as the minimization of maximum values of the DMF of the controlled structure for optimum searching. By resorting to the defined criterion and the particle swarm optimization (PSO), the effects of varying the crucial parameters on the performance of ATMDI have been scrutinized in order to probe into its superiority. Furthermore, the results of both ATMD and tuned mass dampers inerter (TMDI) are included into consideration for comparing. Results corroborate that the ATMDI outperforms both ATMD and TMDI in terms of the effectiveness and robustness. Especially, the ATMDI may greatly reduce the demand on both the mass ratio and inerter mass ratio, thus being capable of further miniaturizing both the ATMD and TMDI. Likewise the miniaturized ATMDI still keeps nearly the same stroke as the TMDI with a larger mass ratio. Hence, the ATMDI is deemed to be a high performance control device with the miniaturization and suitable for super-tall buildings.

• Structural Engineering and Mechanics
• /
• 제78권2호
• /
• pp.125-134
• /
• 2021

In this paper, the effects of Tuned Mass dampers (TMDs) on the reduction of the vertical vibrations of a real horizontally curved steel box-girder bridge due to different traffic loads are numerically investigated. The performance of TMDs to reduce the bridge vibrations can be affected by the parameters such as dynamic characteristics of TMDs, the location of TMDs, the speed and weight of vehicles. In the first part of this study, the effects of mass ratio, damping percentage, frequency ratio, and location of TMDs on the performance of TMDs to decrease vertical vibrations of different sections of bridge deck are evaluated. In the second part, the performance of TMD is investigated for different speeds and weights of traffic loads. Results show that the mass ratio of TMDs is the more effective parameter in reducing imposed vertical vibration in comparison with the damping ratio. Furthermore, it is found that TMD is very sensitive to its tuned frequency, i.e., with a little deviation from a suitable frequency, the expected performance of TMD significantly decreased. TMDs have a positive and considerable performance at certain vehicle speeds and this performance declines when the weight of traffic loads is increased. Besides, the results reveal that the highest impact of TMD on the reduction of the vertical vibrations is when free vibrations occur for the bridge deck. In that case, maximum reductions of 24% and 59% are reported in the vertical acceleration of the bridge deck for the forced and free vibration amplitudes, respectively. The maximum reduction of 13% is also obtained for the maximum displacement of the bridge deck. The results are mainly related to the resonance condition.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권2호
• /
• pp.170-178
• /
• 2011

본 논문에서는 MEMS 센서와 블루투스 무선 통신 모듈을 이용하여 교량 모니터링을 위한 무선 계측 시스템 개발에 대한 연구를 수행하였다. 이를 위하여 MEMS 센서의 가속도 측정 범위 및 주파수 응답 범위 성능을 검증하기 위한 실험을 수행하여 교량 계측에 적합성 여부를 판단하였다. 실험 결과, 고성능의 압전형 가속도 센서에 비하여 동적 범위와 측정 주파수 범위의 성능은 낮으나 30Hz 미만의 저주파수 대역 측정에는 무리가 없을 것으로 판단한다. 그리고 최대 통신 거리 측정 결과, 280m정도의 성능을 가지고 있음을 확인하였다. 마지막으로 개발된 무선 가속도 센서 시스템을 공용중인 교량에 설치한 후, 교통하중에 의한 진동데이터를 획득하여 교량의 동특성을 실시간 분석하였다. 분석결과는 대상교량의 FE 해석결과와 비교를 통하여 무선 가속도 센서 시스템의 성능을 평가하였다. 실험 결과, MEMS 센서와 블루투스 무선 통신 모듈을 이용하여 개발한 무선 가속도 센서는 교량과 같은 저주파수 진동특성을 갖는 건설구조물의 계측에 효과적으로 사용할 수 잇을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.183-187
• /
• 2012

In the present study, a feasibility study on an innovative satellite attitude control actuator is performed. The actuator is specially designed to generate the reaction torque in an arbitrary axis, so that a satellite attitude can be controlled by using itself. It consists of a spherical flywheel and electromagnets for levitation and rotation control of the ball. As the earlier study, a rotating performance test on the spherical actuator is conducted in a single rotating axis and vertical levitation condition. From the test results, it can be confirmed that the maximum speed and torque of the innovative device are 7,200rpm and 0.7Nm, respectively. Using torque-voltage characteristics of the spherical motor, an open-loop control (V/f constant control) is performed, and the test results show excellent control performance in acceleration and deceleration phases.