• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.18-24
• /
• 2013

An experimental study was performed to investigate the characteristics of combustion pressure and exhaust emissions when the pilot injection timing and EGR rate were changed in a CRDI 4-cylinder diesel engine. The pilot injection timing and EGR rate have a significant impact on the combustion and emission characteristics of diesel engine. In this study, the pilot injection timing and EGR rate variation were conducted to 2000rpm of engine speed with torque 50Nm. Combustion pressure and heat release rate were decreased under high EGR rate conditions but increased under the pilot injection timing $20^{\circ}$(BTDC). IMEP and the maximum pressure in cylinder(Pmax) were decreased under the same injection timing with the increase of EGR rate. The NOx emission was decreased with increasing the EGR rate. On the other hand, in the same injection timing conditions, CO, HC, $CO_2$ emissions were increased with increasing the EGR rate.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.776_777
• /
• 2009

Optimal efficiency control of synchronous reluctance motor(SynRM) is very important in the sense of energy saving and conservation of natural environment because the efficiency of the SynRM is generally lower than that of other types of AC motors. This paper is proposed a novel efficiency optimization control of SynRM considering iron loss using neural network(NN). The optimal current ratio between torque current and exciting current is analytically derived to drive SynRM at maximum efficiency. This paper is proposed an efficiency optimization control for the SynRM which minimizes the copper and iron losses. The design of the speed controller based on adaptive learning mechanism fuzzy-neural networks(ALM-FNN) controller that is implemented using fuzzy control and neural networks. The objective of the efficiency optimization control is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. The control performance of the proposed controller is evaluated by analysis for various operating conditions. Analysis results are presented to show the validity of the proposed algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.156-165
• /
• 1997

In the practical control systems, the dynamic range of actuatiors is limited(or saturated) when actuators are driven by sufficiently large signals. This gives rise to a nonlinearity as a result of actuator saturation. For example, the upper limit is imposed on productive capability by available factory space and capital equipment. Other examples of those kinds of actuator saturations are a maximum torque of the actua- ting motors and a throttle position in an aircraft speed control A saturating actuator may lead not only to a large overshoot during start-up and shut-down, but also to deterioration of the performance due to the uncertainties. That is, the speed of response is decreased and, possibly, the system output may not follow the lalrge reference inputs. The large-overshoot may be accompanied by rest wind-up(or called by integra- tor wind-up) which comes from controllers with integral action in saturation operation regions. Eventually, as the overshoot increases, the system has a limit cycle or becomes oscillatorily unstable. Due to these cir- cumstances, many studies are focused on the stability and robustness of the nonlinear systems with satu- rating actuator in the time-domain as well as in the frequency-domain.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.195-197
• /
• 2007

The water pumping system uses a variable speed single phase induction motor driven a centrifugal pump by field oriented control(FOC) inverter. The MPPT using a DC-DC converter controlled the duty cycle to track maximum power from PV under different insolation conditions. The duty cycle directly relate with a flux producing current control($i_{ds}$). The FOC inverter uses a current control voltage source inverter(CC-VSI). The simulation results are shown that the characteristics and performance of drive system, which varies as each conditions of light by expresses in voltage$(V_{dq})$, current$(I_{dq})$, speed of motor and torque.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.66-71
• /
• 2011

This study analyzed the mechanical characteristics and evaluated their subsequent performance for two types of seals which reinforced characteristics with lower friction and anti-wear functions among the foremost important features in the automotive engine seals; one with the addition of glass fiber to PTFE(Polytetrafluoro ethylene); the other with the addition of self-lubricant molybdenumin addition to the glass fiber. Based on the configuration design of seal installed to the front part in the automotive engine, this study carried out interpretations on the stress and reaction for those two types of oil seals to compare the maximum stress and contact load generated from the seal steel, rubber and PTFE lip. This study also verified the stress concentration and anti-wear performance through the coefficient of friction, torque and durability test by producing two types of PTFE seals actually.

• Journal of Biosystems Engineering
• /
• v.17 no.3
• /
• pp.237-246
• /
• 1992

This study was conducted to investigate experimentally the effect of track tension on the tractive performance of rice combine. The experiment was carried out at the two in-door soil bins with soil types of loam and sandy loam. The initial track tension was varied by three different values of 0.71, 1.75 and 3.84kN at three different forward velocity settings of 0.17, 0.32 and 0.45m/s, respectively. The data acquisition system was designed and used for the measurement of pull, driving axle torque and its velocity under the test conditions to calculate the tractive efficiency. Results of the study were summarized as follows : 1) The effect of the initial track tension on the tractive efficiency was found being significantly dependent on soil types but not on forward velocities. Therefore, the benifit of adjusting the initial track tension may be obtained when the types of soils on which combines operate are changed. 2) In loam, tractive efficiency decreased with increase in track tension. However, it increased in sandy loam until it reached to a peak value and then decreased with increase in track tension. 3) The maximum tractive efficiency of the tested combine was obtained with an initial track tension of about 1.75kN on sandy loam, and below that on loam at about 5% slippage without being noticeably influenced by the forward velocity.

• Journal of Biomedical Engineering Research
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2011

An active training system has been developed to assist the upper extremity function in patients with spasticity. We also evaluated the performance of the developed assistive system in five normal subjects and one hemiplegic patient. The maximum voluntary contraction (MVC) tests for biceps brachii and triceps brachii were performed and the relationship between linear enveloped EMG signal and the elbow joint torque was found. In order to implement an active training, our system was designed to allow isokinetic movement only when the subject generates elbow joint motion larger than the pre-fixed threshold level. The proposed EMG-feedback control method could provide active exercises, resulting in better rehabilitation protocol for spastic patients.

• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.92-99
• /
• 2015

The diameter of a new wheel in EMUs is 860mm and it can be used up to 773mm. To obtain an predefined acceleration despite wheel diameter changes, the tractive efforts of the vehicles must be properly controlled. In the commencement of this study, acceleration tests were performed for empty EMUs when the wheel diameter was changed to 860mm, 820mm and 780mm, respectively. In order to deal with more complicated running conditions, we developed dynamic simulation models of the EMUs using VI-Rail, and simulated the models in empty and full passenger loads, respectively. Using the simulation results, we analyzed the gradient of time-velocity graphs by considering the changes of the total weight vehicles and moment of inertia of the wheelsets as well as tractive effort according to the wheel diameter changes. As the results, it was found that there are significant differences in acceleration performances according to the wheel diameters and the payloads of EMUs. In case of 860mm which is the maximum wheel diameter, the test & simulation results show that the vehicle couldn't reach the predefined acceleration, 3.0km/h/s, due to lack of tractive effort.

• Macromolecular Research
• /
• v.14 no.2
• /
• pp.187-193
• /
• 2006

Organoclay, was applied as a filler, in place of carbon black and silica, to a natural rubber (NR)/butadiene rubber (BR) blend. A compounding method was used to disperse and separate the layered silicates. The effect of a coupling agent on the vulcanizates was evaluated using both the silica and organoclay filled compounds. After the compounding processes were completed, the XRD diffraction peaks disappeared, but then reappeared after vulcanization. The scorch times for the organoclay-filled compounds were very short compared to those for carbon black and silica-filled compounds. The organoclay-filled compounds showed high values of tensile strength, modulus, tear energy, and elongation at the break. When ranked by viscosity, the compounds appeared in the following order: silica > silica (Si-69) > organoclay > organoclay (Si-69) > carbon black. Fractional hysteresis, tensile set, and wear rates were very consistent with the viscosity of the vulcanizates. The Si 69 coupling agent increased reversion resistance, the maximum torque values in the ODR, modulus, and wear resistance, but decreased elongation at the break, fractional hysteresis, and tension set of the vulcanizates.