• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.71-76
• /
• 2009

This study was conducted to investigate the load acting on a tractor engine when it delivers the maximum power at drawbar. The results of the drawbar tests on the 5 locally-made and 14 imported tractors conducted at NIAE in 2004, and the 15 tractors tested at OECD test stations in foreign countries were analyzed and presented by the torque load ratio, defined as a ratio of the engine torque load caused by drawbar pull to its full-load capacity, as a function of pull speed. The NIAE test results showed that the torque load ratio increased from 20 to 80% with pull speed less than 5 km/h. At speeds faster than 5 km/h, it was 80${\sim}$110% regardless of the pull speed. However, the OECD test results showed that the torque load ratio was evaluated mostly to be 70${\sim}$90% in the entire pull speed range. The same trend was also shown for the maximum drawbar load. The difference in the torque load ratio may be attributable to bias-ply tires for locally-made and some imported tractors. It is also suggested that the input torque load may be increased safely up to 120% of the full load capacity of the tractor engine for an accelerated life test of tractor transmissions.

• Journal of the Ergonomics Society of Korea
• /
• v.20 no.2
• /
• pp.83-97
• /
• 2001

Korea has become an aged society according to the UN specifications. The number of the aged population will increase drastically, and the number of single aged people will also increase. Products used in our daily life are manufactured within the normal capabilities of people. Thus, aged people have encountering problems in using them. Numerous products are used in our daily lives. The purpose of this study is to find the acceptable torque for aged people to open the caps of processed food containers. Depending on the size and shape of the opening hand, hand operation has been classified into three categories. A total of one hundred and nine people participated in this study. Fifty nine people in the 20-30 year old range and fifty people in their 60-70's. Results of the study are as follows: 1) For all categories the acceptable cap torque data for the aged people are established. To satisfy 95% of the aged people, it was found that $74N{\cdot}cm$ for type A caps, and $141N{\cdot}cm$ for B type caps. and $214N{\cdot}cm$ for type C were the acceptable torque levels. 2) The appropriate level of torque for opening the cap was found to be 70% of the maximum torque for the aged people.(71.4% for type A. 71.4% for type B. 72.2% for type C). 3) Capabilities of the 70's drops sharply in function related to opening cap (maximum torque, gripping force, and wrist movement range). 4) Among aged subjects, 65.0% for type A, 42.0% for type B, and 68.8% for type C, had difficulties in opening the container caps.

• The korean journal of orthodontics
• /
• v.24 no.1 s.44
• /
• pp.87-94
• /
• 1994

The purpose of this study was to evaluate the torque effect of othodontic wires. Ten types of orthodontic wires (five types of materials, two types of cross-sectional dimensions) were selected. Each group of ire type was constituted with five specimens. These specimens were tested on the universal testing machine(Instron) with specially-designed jig. The torque-twist curve of each wire was obtained and the results were analyzed statistically. The results were as follows. 1. 0.017'$\times$ 0.025' wire showed more torque effect than 0.016'$\times$ 0.022' wire at the same twist. 2.Torque effect was the greatest in stainless steel and the least in Nitinol. 3.The maximum amount of torque was the greatest in heat-treated Blue Elgiloy and the least in Nitinol.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.709-710
• /
• 2008

In this paper, we calculated permanent magnetic linkage flux ${\psi}_{\alpha}$ and Ld, Lq parameters of IPMSM and compared two model which has different barrier width. IPMSM has two kinds of torque that reluctance torque and magnetic torque. In constant torque region, using the Maxwell stress tensor method, we calculated the torque and current phase angle ${\beta}$ which has appeared maximum torque. In weakening flux region, we calculated the current phase angle ${\beta}$ which flux ${\psi}_o$ lower than limited flux ${\psi}_{omax}$. From the current phase angle ${\beta}$, we calculated torque by torque equation and compared two model characteristic.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.8
• /
• pp.21-25
• /
• 2009

Magnetic fluxes for maximum efficiency are calculated at five operating points as speed and torque are varied. The surface of magnetic flux for maximum efficiency is calculated by using the five points, Then, maximum efficiency control is fulfilled with the magnetic flux calculated from the surface of magnetic flux at a given speed and torque. Simulation results verify the effectiveness of the proposed method.

• New & Renewable Energy
• /
• v.10 no.4
• /
• pp.9-15
• /
• 2014

In this study pressure and shaft torque pulsation were measured with variation of head and flow during the model test for a 15 MW Francis Turbine. Pressure pulsations were measured at the inlet of the spiral casing and 4 points in the cone of the diffuser and shaft torque pulsation at the upper position of the turbine. The maximum amplitude of pressure pulsation appeared 2.03% of the maximum rated head with the frequency of 25% of the rated revolution and at the guide vane opening of $10^{\circ}$. Shaft torque pulsation appeared 0.01% of the rated shaft torque, fairly low value. Air was admitted through the cone and pressure pulsation gradually decreased with increase of air flow and kept nearly constant after 5% of the rated flow. A new Francis turbine of which specific speed is 115 m-kW had been designed to rehabilitate the old one and the model test was performed at EPFL. The commercial code, STAR-$CCM^+$ was used for numerical simulation of flow.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.151-154
• /
• 2002

This paper presents an implementation of high-dynamic performance control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo drive system with direct torque control(DTC). The estimation of the stator flux and torque are obtained by using flux observer which a saturated inductance Ld and Lq of d-q axises can be compensated by using the neural network from measuring the modulus and angle of the stator current space vector. To obtain fast torque response and maximum torque/current, the reference command flux is ensured by imposing Ids=Iqs. The control strategy is proposed to fast response and optimal efficiency for RSM drive. The developed digitally high-performance control system are shown a good response characteristic of control results and high performance features using 1.0kW RSM.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.193-200
• /
• 2011

The external disturbance torque acting on a low earth orbit spacecraft was analyzed. For the Earth pointing attitude, the maximum torque to the spacecraft is about $8.3{\times}10^{-4}$ Nms and the momentum accumulated for an orbit is about 1.4 Nms and for the Sun pointing attitude, the maximum torque to the spacecraft is about $1.6{\times}10^{-3}$ Nms and the momentum is accumulated about 3.0 Nms in the spacecraft body reference frame. The analysis results confirm that the size of magnetic torquer selected previously for the satellite is sufficient to manage the accumulated momentum by considering the dumping capacity for an orbit.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.135-141
• /
• 2002

This paper presents an implementation of high-dynamic performance of position sensorless motion control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo system with direct torque control(DTC), The problems of DTC for high-dynamic performance and maximum efficiency RSM drive due to a saturated stator linkage flux and nonlinear inductance curve with various load currents, The accurate estimation of the stator flux and torque are obtained using stator flux observer of which a saturated inductance Ld and Lq can be compensated by adapting from measurable the modulus and angle of the stator current space vector. To obtain fast torque response and maximum torque/current with varying load current, the reference command flux is ensured by imposing Ids=Iqs. This control strategy is proposed to fast response and optimal efficiency for RSM drive. In order to prove rightness of the suggested control algorithm, the actual experiment carried out at ${\pm}$20 and ${\pm}$1500 rpm. The developed digitally high-performance control system are shown some good response characteristic of control results and high performance features using 1.0kW RSM of which has 2.57 Ld/Lq salient ratio.

• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.27-36
• /
• 1984

This study was carried out to investigate the effects of the tilling depth, tilling travel speed and soil shear stress on the tilling load characteristics and power requirement for rotary tillers. The results obtained from the study are summarized as follows. 1. The average and maximum PTO torque increased as the tilling depth, tilling pitch and soil shear stress increased. A multiple linear regression equation to estimate the average PTO torque in terms of the above parameters was developed. 2. The ratios of maximum PTO torque to the average torque were in the range of 1.17 to 1.65 for the various tilling conditions tested. The variation in PTO torque increased greatly as the tilling pitch and soil shear stress increased, but decreased as the tilling depth increased. 3. Power requirement for the PTO shaft increased with the tilling depth, travel speed and soil shear stress, but decreased slightly as the tilling pitch increased. A multiple linear regression equation to estimate power requirement for the PTO shaft in terms of the above parameters was developed. 4. The specific power requirement for the rotary tiller was in the range of $0.008-0.015ps/cm^2$ for the various tilling conditons tested. The specific tilling capacity decreased as the tilling depth and soil shear stress increased, but increased with the tilling pitch. A multiple linear regression equation to estimate the specific tilling capacity in terms of the above parameters was developed.