• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2037-2047
• /
• 1991

본 연구에서는 재료 결정격자의 기본단위나 결정립의 형상등 가장 기본적인 형태가 6각형이라는 점에 착안하여 취성재료의 파손모델로 부재들의 결손을 이용하는 결손확률모델을 제안하여 부재결손에 따른 각각의 파손 해석모델과 결손확률을 구한다. 그리고 비결손모델에서 구한 기본인장하중을 기초로 하여 해석하고자 하는 하중하에서 각각의 파손해석모델을 모델링하여 유한요소법으로 부재결손에 따른 요소중심에서의 최대주응력을 구하여 이론극한인장강도와의 비와 결손확률로 취성재료의 파손확률을 구한다. 또한 취성정도에 따른 균열길이에 대한 치수 매개변수를 구함으로써 재료강 도 연구에 기초가 되게 한다.

• 한국안전학회지
• /
• 제29권3호
• /
• pp.1-7
• /
• 2014

In this study, for the evaluation of the static and fatigue joining strength of the joint, the geometry of the cross-tension specimen was adopted. The specimens were produced with optimal joining force and fatigue life of the clinch joint specimens was evaluated. The material selected for use in this study was cold rolled mild steel (SPCC) with a thickness of 0.8 mm. The maximum tensile load was 708 N for the specimen with single point. The fatigue endurance limit (=42.6 N) per point approached to 6% of the maximum tensile strength at a load ratio of 0.1, suggesting that the joints are vulnerable to cross-tension loading during fatigue. Compared to equivalent stress and maximum principal stress, the SWT fatigue parameter and equivalent strain can properly predict the current experimental fatigue life. The SWT parameter can be expressed as $SWT=2497.5N^{-0.552)_f$.

• 한국지반공학회지:지반
• /
• 제14권5호
• /
• pp.219-234
• /
• 1998

초기수평 응력상태를 모사하여 응력이 변형계수에 미치는 영향을 검토 하기 위하여 암석 시료에 대하여 공내재하 변형 실내시험을 했다. 실험은 수평 응력의 크기, 응력비, 측정지점을 변화 시켜서 변형계수를 측정하였다. 측정결과 응력의 크기가 증가함에 따라 변형계수가 증가하며 최대 최소응력비가 커짐에 따라 변형계수는 최소응력 방향에서는 증가하고, 최대응력 방향에서는 감소하는 경향을 보였다. 이는 측정 위치에서 접선음력의 크기 변화에 따른 것으로 초기응력의 크기, 방향 및 내압의 크기에 따라 응력이 압축, 인장 또는 압축-인장상태로 바뀌기 때문이다. 따라서 변형 계수 측정시 이들의 영향을 분석한 후 결과치를 해석하여야 한다. 이와 같은 해석은 공내재하 변형 측정 결과 뿐만 아니라 내압이 있는 가스 저장 또는 압축터널 설계 및 터널 계측 결과 해석에도 적용 되어야 한다.

• 펄프종이기술
• /
• 제31권5호
• /
• pp.73-85
• /
• 1999

Yield and fracture are separated in the tensile failure of paper. Failure in the machine direction of photocopy paper is contrasted with failure in the cross-machine direction . The ratios of distortion (shape change) to dilatation (volume change) for individual elements at yield and fracture are described. The ratios of distortion to dilatation are measured and compared to predicted values of the strain energy density theory. To evaluate the effect of the angle from the principal material direction on the strain energy density theory. To evaluate the effect of the angle from the principal material direction on the strain energy density factor, samples are prepared from machine direction to cross-machine direction in 15 degree intervals. the strain energy density of individual elements are obtained by the integration of stress from finite element analysis with elastic plus plastic strain energy density theory. Poison's ratio and the angle from the principal material direction have a great effect ion the ratio fo distortion to dilatation in paper. During the yield condition, distortion prevails over dilatation . At fracture, dilatation is at a maximum.

• 터널과지하공간
• /
• 제23권5호
• /
• pp.362-371
• /
• 2013

수압파쇄법으로 최대수평주응력 크기 규명에 필요한 요소 중 하나인 암반의 인장강도를 측정하는 방법에 대해 연구하였다. 석모도 시추공에서 회수한 화강암 시료에 대해 두 가지 실내시험(중공원통 인장시험 및 압열인장시험)으로 인장강도를 측정하고 두 결과가 차이를 보이는지 비교하였다. 중공원통 인장시험에서는 높은 수압증가율 상태에서 더 높은 인장강도를 보여, 현장의 수압파쇄시험에서 보인 수압 증가율 상태에서 측정된 인장강도나 그 증가율로 보정된 인장강도를 이용해야한다는 점을 보였다. 인장강도에 대한 수압 증가율 효과와 크기효과를 보정하면 중공원통 인장시험 결과는 압열인장시험 결과와 유사하게 나타났으며 이는 수압파쇄 인장강도를 위해 압열인장강도를 이용할 수도 있다는 점을 시사한다.

• The Journal of Advanced Prosthodontics
• /
• 제16권2호
• /
• pp.77-90
• /
• 2024

PURPOSE. The study aims to investigate the influence of the ferrule effect and types of posts on the stress distribution in three morphological types of the maxillary central incisor. MATERIALS AND METHODS. Nine models were created for 3 maxillary central incisor morphology types: "Fat" type - crown 12.5 mm, root 13 mm, and buccolingual cervical diameter 7.5 mm, "Medium" type - crown 11 mm, root 14 mm, and buccolingual cervical diameter 6.5 mm, and "Slim" type - crown 9.5 mm, root 15 mm, and buccolingual cervical diameter 5.5 mm. Each model received an anatomical castable post-and-core or glass-fiber post with resin composite core and three ferrule heights (nonexistent, 1 mm, and 2 mm). Then, a load of 14 N was applied at the cingulum with a 45° slope to the long axis of the tooth. The Maximum Principal Stress and the Minimum Principal Stress were calculated in the root dentin, crown, and core. RESULTS. Higher tensile and compression stress values were observed in root dentin using the metallic post compared to the fiber post, being higher in the slim type maxillary central incisor than in the medium and fat types. Concerning the three anatomical types of maxillary central incisors, the slim type without ferrule height in mm presented the highest tensile stress in the dentin, for both types of metal and fiber posts. CONCLUSION. Post system and tooth morphology were able to modify the biomechanical response of restored endodontically-treated incisors, showing the importance of personalized dental treatment for each case.

• Computers and Concrete
• /
• 제7권2호
• /
• pp.191-202
• /
• 2010

A laboratory investigation was conducted to characterize the constitutive property behavior of Cor-Tuf, an ultra-high-performance composite concrete. Mechanical property tests (hydrostatic compression, unconfined compression (UC), triaxial compression (TXC), unconfined direct pull (DP), uniaxial strain, and uniaxial-strain-load/constant-volumetric-strain tests) were performed on specimens prepared from concrete mixtures with and without steel fibers. From the UC and TXC test results, compression failure surfaces were developed for both sets of specimens. Both failure surfaces exhibited a continuous increase in maximum principal stress difference with increasing confining stress. The DP tests results determined the unconfined tensile strengths of the two mixtures. The tensile strength of each mixture was less than the generally assumed tensile strength for conventional strength concrete, which is 10 percent of the unconfined compressive strength. Both concretes behaved similarly, but Cor-Tuf with steel fibers exhibited slightly greater strength with increased confining pressure, and Cor-Tuf without steel fibers displayed slightly greater compressibility.

• Geomechanics and Engineering
• /
• 제7권4호
• /
• pp.403-430
• /
• 2014

Shale gas formations exhibit strong mechanical and strength anisotropies. Thus, it is necessary to study the effect of anisotropy on the hydraulic fracture initiation pressure. The calculation model for the in-situ stress of the bedding formation is improved according to the effective stress theory. An analytical model of the stresses around wellbore in shale gas reservoirs, in consideration of stratum dip direction, dip angle, and in-situ stress azimuth, has been built. Besides, this work established a calculation model for the stress around the perforation holes. In combination with the tensile failure criterion, a prediction model for the hydraulic fracture initiation pressure in the shale gas reservoirs is put forward. The error between the prediction result and the measured value for the shale gas reservoir in the southern Sichuan Province is only 3.5%. Specifically, effects of factors including elasticity modulus, Poisson's ratio, in-situ stress ratio, tensile strength, perforation angle (the angle between perforation direction and the maximum principal stress) of anisotropic formations on hydraulic fracture initiation pressure have been investigated. The perforation angle has the largest effect on the fracture initiation pressure, followed by the in-situ stress ratio, ratio of tensile strength to pore pressure, and the anisotropy ratio of elasticity moduli as the last. The effect of the anisotropy ratio of the Poisson's ratio on the fracture initiation pressure can be ignored. This study provides a reference for the hydraulic fracturing design in shale gas wells.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.111-115
• /
• 2001

The die design for hot forging was investigated for manufacturing precisely of scroll rotor made with Al-Si alloy. A scroll rotor is a non-symmetric 3-D shape part, having involute wraps. Disk-shaped billet of Al-Si alloy was extruded to wraps and boss simultaneously. Because the involute wraps is not axi-symmetric, the flow velocity and the stress of die is very much different at each portion. Moreover, the die in wraps portion is a cantilever beam and fractured. In this paper, the analysis of forming and die stress is investigated using the FEM tool, DEFORM-3D. The tensile strength of tool material is $250kg/mm^{2}$. From the analysis results, we can find the maximum principal stress of die is over the fracture strength and redesign the die. The prototype forged part is superior in net shaping and microstructure.

• Restorative Dentistry and Endodontics
• /
• 제31권6호
• /
• pp.427-436
• /
• 2006

본 연구의 목적은 3차원유한요소분석법을 이용하여 정상 상악 제2소구치의 협측부의 응력분포에 다양한 교합응력이 미치는 영향을 평가하고자 하였다. 상악 제2소구치의 3차원유한요소모델을 형성한 후 형성된 모델에 3종류의 정적인 500N 점하중의 응력조건을 부여하였다. ANSYS 프로그램 (Swanson Analysis Systems, Inc., Houston, USA)으로 최대주응력과 최소주응력을 4개의 수평면 상(CEJ 상방 1 mm, CEJ 상방 0.5 mm, CEJ, CEJ 하방 0.5 mm)에서 분석하여 다음 결과를 얻었다. 1. peak stress가 협측 백악법랑경계를 따라 비대칭적인 모습으로 나타났다. 2. 압축응력 값은 법랑질의 압축파괴응력 범위 내에 있었지만 인장응력은 법랑질의 인장파괴응력 범위를 넘어섰다. 3. 비우식성치경부병소를 발생시키는 주요인은 설측교두의 협측경사면에 가해지는 교합압에 의한 인장응력이라고 보여진다.