• 한국식품과학회지
• /
• 제20권6호
• /
• pp.749-754
• /
• 1988

김장용 배추잎의 조직감 평가를 위하여 절단시험 및 압착시험에 의한 기계적 측정을 시도하였으며 관능검사 결과와 비교하였다. 배추잎의 절단강도는 소금절임이나 가열데침에 의하여 증가하였으며 15% 식염용액에서 5시간 절임으로써 최대치에 도달하였다. 압착시험에서 얻은 압착강도와 회복높이는 가열데침이나 소금절임에 의하셔 감소되었으며 파열점은 소실되었나. 생배추를 $CaCl_2$ 용액에 처리할 경우 절단강도, 압착강도, 파열강도가 모두 증가하였으나 절임배추나 가열데침한 배추에서는 $Ca^{++}$의 이러한 영향이 나타나지 않았다. 배추잎의 절단 장도는 절임배추의 견고성과 씹힘성을 나타내는 지표로 사용될 수 있을 것으로 판단되었다. 압착강도는 파열강도는 가열데침에 의한 배추잎의 조직감 변화를 나타낼 수 있었으나 소금절임한 배추의 견고성이나 씹힘성 지표로는 사용될 수 없었다.

• 공업화학
• /
• 제27권3호
• /
• pp.259-264
• /
• 2016

본 연구에서는 norbonene dialkyl ester 6종을 isoprene rubber에 적용하여 내분비계 교란물질인 DEHP에 대한 대체 가능성을 평가하였다. IR 시편은 isoprene rubber (IR)와 norbonene dialkyl ester, 가황제 등을 배합하여 제작하였으며, 토크값, 스코치 시간, 최적가황시간, 무니점도를 측정하여 가공성을 평가하였고, 경도, 인장강도, 100% modulus, 신율 등물성을 평가하여 이를 DEHP를 적용한 경우와 비교하였다. 그 결과 토크 값의 경우 최저토크, 최대토크 모두 DEHP 보다 낮거나 유사한 값을 나타내었고, 스코치 시간, 최적가황시간은 DEHP보다 같거나 길게 측정되었다. 무니점도는 DEHN이 낮은 값을 나타내어 DEHP를 첨가한 경우보다 가공성이 우수함을 확인하였다. 경도와 열적 특성의 경우 norbornene계 화합물이 DEHP와 같거나 유사한 경향을 보였다. 인장특성의 경우 선형의 알킬기를 가진 norbornene계 화합물을 적용한 경우가 우수함을 확인하였다.

• 한국분말재료학회지
• /
• 제11권5호
• /
• pp.412-420
• /
• 2004

The purpose of the present study is to determine an optimum composition using cheaper powders keeping with high performance of hard rock cutting diamond saw blade. With 50Fe-20(Cu . Sn)-30Co specimen, a part of Co was replaced by Ni(5%, 10%, and 15%, respectively). These specimens were hot pressed and sintered for predetermined time at various temperature. Sintering is performed by two different methods of temperature controlled method and specimen dimension controlled method. In order to determine the property of the sintered diamond saw blade, 3 point bending tester, X-ray diffractometer, and SEM were used. As the Co in the bond alloy was replaced by Ni, the hardness of the specimen increased. Thus the 50Fe-20(CuㆍSn)-15Co-15Ni specimen showed the maximum hardness of 104(HRB). The results of 3 point bending test showed that flexure strength decreased along with increase in Ni content. This is attributed to the formation of intermetallic compound(Ni$_{x}$Sn) determined by X-ray diffraction. The fracture surface after 3 point bending test showed that diamond was fractured in the specimen containing 0%, 5%, and 10%Ni, and the fracture occurred at the interface between diamond and matrix in the specimen containing 15%Ni. The cutting ability test showed that the abrasive property was not changed in the specimen containing 0%, 5%, and 10%Ni. The optimum composition determined in this study is 50Fe-20(CuㆍSn)-20Co-10Ni.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.191-195
• /
• 2012

Heavy flint optical glass(SF57HHT) is new material that has extremely high transmittance. Due to brittleness and high hardness, optical glass is one of the most difficult to materials for ultra-precision turning. According to the hypothesis of ductile machining, all materials, regardless of their hardness and brittleness, will undergo transition from brittle to ductile machining region below critical undefromed chip thickness. In this study, cutting test was carried out to evaluate cutting performance of heavy flint glass using ultra-precision machine with single crystal diamond bite. The machined workpiece surface topography, tool wear and surface roughness were examined using AFM and SEM. The experimental results indicate that the machining mode become the brittle mode to ductile mode, when the maximum undeformed chip thinkness is large than critical value. Tool wear mainly occurs on the flank face and its wear mechanism is dominated by abrasion. This study demonstrates the feasibility of SF57HHT by diamond turning.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.460-469
• /
• 2000

A study on the corrosion behavior of RE36 steel for marine structure was investigated with parameters such as micro-Vickers hardness, corrosion potential and corrosion current density measurement of weld metal(WM), base metal (BM) and heat affected zone(HAZ), Al anode generating current and Al anode weight loss quantity in case of cathodic protection. And we carried out slow strain rate test(SSRT) in order to research mechanical properties such as stress at maximum load, percent strain, time to fracture and strain to failure ratio etc and to find out limiting cathodic polarization potential for hydrogen embrittlement with applied cathodic polarization potential. Hardness of HAZ part was the highest among those three parts and also galvanic corrosion susceptibility was the highest in HAZ part among those three parts due to the lowest corrosion potential than other parts. However corrosion current density was the highest in WM part among those three parts. And the optimum cathodic polarization potential showing the best mechanical properties obtained by SSRT method with applied constant cathodic potential was from - 770mV to - 875mV(SCE). However it is suggested that limiting cathodic polarization potential indicating hydrogen embrittlement on the mechanical properties was under - 900mV(SCE).

• Restorative Dentistry and Endodontics
• /
• 제38권1호
• /
• pp.36-42
• /
• 2013

Objectives: This study evaluated the antibacterial effect and mechanical properties of composite resins ($L_{CR}$, $M_{CR}$, $H_{CR}$) incorporating chitosan with three different molecular weights (L, Low; M, Medium; H, High). Materials and Methods: Streptococcus (S). mutans 100 mL and each chitosan powder were inoculated in sterilized 10 mL Brain-Heart Infusion (BHI) solution, and was centrifuged for 12 hr. Absorbance of the supernatent was measured at $OD_{660}$ to estimate the antibacterial activities of chitosan. After S. mutans was inoculated in the disc shaped chitosan-containing composite resins, the disc was cleansed with BHI and diluted with serial dilution method. S. mutans was spread on Mitis-salivarius bacitracin agar. After then, colony forming unit (CFU) was measured to verify the inhibitory effect on S. mutans biofilm. To ascertain the effect on the mechanical properties of composite resin, 3-point bending and Vickers hardness tests were done after 1 and 3 wk water storage, respectively. Using 2-way analysis of variance (ANOVA) and Scheffe test, statistical analysis was done with 95% significance level. Results: All chitosan powder showed inhibition effect against S. mutans. CFU number in chitosan-containing composite resins was smaller than that of control resin without chitosan. The chitosan containing composite resins did not show any significant difference in flexural strength and Vickers hardness in comparison with the control resin. However, the composite resin, $M_{CR}$ showed a slightly decreased flexural strength and the maximum load than those of control and the other composite resins $H_{CR}$ and $L_{CR}$. Conclusions: $L_{CR}$ and $H_{CR}$ would be recommended as a feasible antibacterial restorative due to its antibacterial nature and mechanical properties.

• 한국주조공학회지
• /
• 제24권6호
• /
• pp.356-365
• /
• 2004

Mechanical properties and microstructures of the Ni-AI-Fe and Ni-AI-Fe-(B, Zr) alloys which containing $10{\sim}30at$.%Fe, 0.1at.%B and/or 0.1at.%Zr have been investigated. The experimental results showed that the microstructures of Ni25Al were changed from a single phase ${\gamma}$ to dual phase ${\gamma}$ and ${\beta}$ by addition of 27at.%Fe. Ni45Al, however, kept the single ${\beta}$ phase even though Fe was added upto 30at.%. The hardness of Ni25Al were increased from $H_RB$ 70 to $H_RC$ 39 by addition of 27at.%Fe. In the case of Ni45Al which have $H_RC$ 37, the hardness was decreased by lOat.%Fe addition, but increased with 30at.%Fe. The yield strength and ultimate compressive strength in the compressive test have showed a similar trend with the hardness change. The strain to fracture was 14% at maximum and achieved in Ni25Al-27at.%Fe and Ni25Al-27at.%Fe-0.1 at.%B alloys. The Ni45Al showed a relatively low strain to fracture as 4%. The impact absorption energy of Ni25Al increased from 0.74 kg-m to 1.81 kg-m by addition of 27at.%Fe. In case of Ni45Al, the addition of lOat.%Fe and lOat.%Fe with small amounts of Band Zr did not change significantly the impact absorption energy of 0.60 kg-m, whereas the addition of 30at.%Fe with small amounts of B and Zr increased it slightly. In fracture tests, both of two basic materials showed the same intergranular fracture but by adding Fe it changed to the cleavage fracture mode or co-existing of cleavage and intergranular fractures.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권1호
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• 한국축산식품학회지
• /
• 제40권4호
• /
• pp.551-562
• /
• 2020

Beef fat was replaced with cold press pumpkin seed oil (PSO; 0%, 5%, 15%, and 20%) in the production of bologna-type sausages. A value of pH, water-holding capacity (WHC), jelly-fat separation, emulsion stability and viscosity values were determined in meat batters. Thiobarbituric acid reactive substances (TBARS), color, and textural characteristics (TPA, shear test, penetration test) were determined in end-product at 1, 7, 14, 21, and 28 days of storage at 4℃. The pH values were varied between 6.06 and 6.08. With the increase in the level of PSO in meat batters, there was a significant increase in WHC, jelly-fat separation and viscosity values (p<0.05) while a significant decrease in emulsion stability (p<0.05). TBARS values of sausages were found to be significantly higher than in the control group (p<0.05), and this trend continued during storage. Increasing of PSO level were caused a significant increase in L* and b* values while a decrease in a* value (p<0.05). Hardness, adhesiveness and chewiness values were significantly reduced whereas cohesiveness and resilience values increased (p<0.05). Maximum shear force and work of shear was significantly decreased as the level of PSO increased (p<0.05). Hardness, work of penetration and the resistance during the withdrawal of the probe values (penetration tests) increased significantly with the increase in the level of PSO (p<0.05). These results indicate that PSO has potential to be use as a replacement of animal-based fats in the production of bologna-type sausages.

• 폴리머
• /
• 제35권4호
• /
• pp.342-349
• /
• 2011

실리카의 표면 개질제인 vinyltriethoxysilane(VTEOS)의 함량에 따른 실리카로 보강된 실리콘 고무의 기계적 물성 변화 및 내열성, 내유성, 압축 영구줄음률, 반발탄성 및 가교밀도 변화를 연구하였다. 결과로 VTEOS의 함량이 2.0 phr까지 증가함에 따라 경도는 상승하였으나 인장강도 파단신율, 인열강도가 감소하였다. 내열시험에서는 VTEOS의 함량이 증가될수록 경도변화, 인장강도 변화율, 파단신율 변화율이 크게 감소하였다. VTEOS 2.0 phr에서 가장 우수한 내열특성을 나타내었다. 또한 VTEOS의 함량이 증가될수록 실리콘 고무의 내유성이 증진되었으며, VTEOS 미첨가 시보다 경도 하락폭이 크게 낮았으며, 파란신율 변화율은 약 2배 이상 감소하였다. 반발탄성도 VTEOS의 함량이 증가될수록 우수하였으며, 압축 영구줄음률 역시 VTEOS가 증가될수록 감소하였다. 가교실험 결과 VTEOS가 증가될수록 최대 토크값와 가교밀도가 크게 향상되었다.