• 제목/요약/키워드: Matrix phase

검색결과 1,547건 처리시간 0.03초

생쥐 LP1-1 세포에서 S phase 동안 nuclear matrix에 고정되어 있는 복제 끝점 (Termination Sites of fleplication Are Anchored to the Nuclear Matrix during S Phase in Mouse LPI-1 Cells)

  • 이형호;이갑열
    • 한국동물학회지
    • /
    • 제37권3호
    • /
    • pp.318-323
    • /
    • 1994
  • The association of replication origins/termini with nuclear matrix during S phase was investigated by DNase digestion of halo structures in synchronized mouse LPI-1 cells. The binding of parental DNA to nuclear matrix was constant throughout S phase. When nuclear matrix was isolated from the cells pulse-labeled with 3H-thvmidine at various stases of S phase, total 3H-labels associated with nuclear matrix were specifically higher at So, Sa and Ss stages than other stases of S phase, suggesting that the newly synthesized DNAs at those stages are not excluded out of nuclear matrix. Similar patterns were obsenred from the pulse-chase experiments, in which cells were pulse-labeled at each stage of S phase and further incubated for 1 hr. These results suggest that the replication origins and termini are fixed at the nuclear matrix, and that the nuclear matrix binding fractions of DNA at 3C-pause may contain a large population of replication origins and termination sites.

  • PDF

고크롬 철계 오버레이용접층의 긁힘마모거동에 미치는 기지상의 영향 (Effect of Matrix Phase on the Abrasive Wear Behavior of the High Cr White Iron Hardfacing Weld Deposites)

  • 백응률
    • Journal of Welding and Joining
    • /
    • 제16권1호
    • /
    • pp.114-124
    • /
    • 1998
  • The effect of matrix phase (austenite, pearlite, martensite) on the low stress abrasion resistance in the chromium-carbide-type high Cr white iorn hardfacing weld deposites has been investigated. In order to examine matrix phase, a series of alloys with different matrix phase by changing the ratio of Cr/C system by heat treatment were employed. The alloys were deposited twice on a mild steel plate using self-shielding flux cored arc welding process. The low stress abrasion resistance of the alloys against sands was measured by the Dry Sand/Rubber Wheel Abrasion Test(RWAT). Even though formation of pearlite phase in the matrix showed higher hardness than that of austenite, there was no observable difference in wear resistance between the pearlite and austenite phase for the same amount of chromium-carbide in the matrix. On the other hand, the formation of martensitic phase,, from heat treated austenitic alloys (high content of Cr), enhanced wear resistance due to its fine secondary precipitates.

  • PDF

DDPWM Based Control of Matrix Converters

  • Li, Yu-Long;Choi, Nam-Sup;Han, Byung-Moon
    • Journal of Power Electronics
    • /
    • 제9권4호
    • /
    • pp.535-543
    • /
    • 2009
  • In this paper, pulse-width modulation (PWM) control strategy of various topologies of matrix converters is presented, which is based on direct duty ratio PWM (DDPWM). Because the DDPWM method has the characteristics of the inherent per-phase modular structure, it can be effectively applied to single-phase, two-phase and three-phase four-leg matrix converters as well as the common three-phase to three-phase matrix converter. Also, this paper treats command generation method in each matrix converter. The feasibility and validity of the proposed method are verified by experimental results.

Compensating Characteristics of Voltage Sag Compensator Utilizing Single-Phase Matrix Converter

  • Yamamoto, Kichiro;Ikeda, Keisuke;Iimori, Kenichi
    • Journal of international Conference on Electrical Machines and Systems
    • /
    • 제2권1호
    • /
    • pp.77-82
    • /
    • 2013
  • By using simulation, compensating characteristics of a voltage sag compensator utilizing single-phase matrix converter is examined. System configuration is described and mathematical model of single-phase matrix converter is derived by using the state space averaging method. In addition, the single-phase matrix converter is stabilized by phase-lead compensation. Finally, compensating characteristics of the compensator is investigated for 500 W R-L load and it is demonstrated that the compensator can operate correctly for loads for the range of power factor 0.6 (lagging) - 0.8 (leading) and for up to 50% voltage sag.

치과 임플란트용 bioactive 세라믹 복합재료의 제조와 미세조직 (Microstructure and Processing of Bioactive Ceramic Composites as Dental Implants)

  • 김부섭
    • 대한치과기공학회지
    • /
    • 제25권1호
    • /
    • pp.21-28
    • /
    • 2003
  • The purpose of this study was to process bio-active glass ceramic composite, reinforced with sapphire fibers, by hot press. Also to study the interface of the matrix and the sapphire fiber, and the mechanical properties. Glass raw materials melted in Pt crucible at 1300$^{\circ}C$ during 3.5 hours. The melt was crushed in ball mill and then crushed material, ground and sieved to $<40{\beta}{\mu}m$. Sapphire fibers cut (30mm) and aligned. Powder and fibers hot pressed. The micrographs show good bonding between the matrix and the fiber and no porosity in the glass matrix. This means ideal fracture phenomena. Glass is fractured before the fiber. This is indication of good fracture strength. EDXS showing aluminum rich phase and crystalline phase. Bright field image of the matrix showing crystalline phase. Also diffraction pattern of TEM showing the crystalline phase and more than one phase. Strength of the samples was determined by 3 point bend testing. Strength of the 10vol% sample was approximately 69MPa, while strength of the control sample is 35MPa. Conclusions through this study as follow: 1. Micrographs show no porosity in the glass matrix and the interface. 2. The interface between the fiber and the glass matrix show no gaps. 3. Fracture of the glass indicates characteristic fiber-matrix separation. 4. Presence of crystalline phase at high processing temperature. 5. Sapphire is compatible with bioactive glass.

  • PDF

질화규소 요업체의 기지상 결정화가 파괴인성에 미치는 영향 (Effect of Crystallization of Matrix Phase on the Fracture Toughness of Silicon Nitride Ceramics)

  • 김남균;김도연;강대갑
    • 한국세라믹학회지
    • /
    • 제24권4호
    • /
    • pp.364-368
    • /
    • 1987
  • The Si5AION7 specimens containing 20% YAG composition have been sintered and then heat treated to induce the crystallization of the matrix glassy phase. Crystallization of YAG phase during the heat treatment was detected from the X-ray diffraction patterns and the consequent changes in room temperature toughness as well as in microstructures were investigated. Almost all the glassy boundary phase were found to crystallize even after 5 minutes of heat treatment and the KC at room temperature decreased accordingly. The results show that the matrix crystallization can be induced by slow cooling from the sintering temperature.

  • PDF

$L1_0$-TiAl 및 $L1_2-(Al,Cr)_3Ti$ 중에 $Al_2Ti$상의 석출거동에 관한 연구 (A Study on the Precipitation Behavior of $Al_2Ti$ Phase in $L1_0$-TiAl and $L1_2-(Al,Cr)_3Ti$)

  • 한창석
    • 열처리공학회지
    • /
    • 제21권1호
    • /
    • pp.20-25
    • /
    • 2008
  • Structural studies have been performed on precipitation hardening and microstructural variations found in Ti-Al-Cr ternary $L1_0$- and $L1_2$-phase alloys using transmission electron microscopy. Both the $L1_0$ and $L1_2$ phase alloys harden by aging at 973 K after solution annealing at higher temperatures. The amount of age hardening of the $L1_2$ phase alloy is larger than that of the $L1_0$ phase alloy. The phase separation between $L1_0$ and $L1_2$ phase have not been observed by aging at 973 K. But $Al_2Ti$ was formed in each matrix alloy during aging. The crystal structure of the $Al_2Ti$ phase is a $Ga_2Zr$ type in the $L1_0$ and a $Ga_2Hf$ type in the $L1_2$ phase, respectively. At the beginning of aging the fine coherent cuboidal $Al_2Ti$-phase are formed in the $L1_0$ phase. By further aging, two variants of $Al_2Ti$ precipitates grow along the two {110} habit planes. On the other hand, in the $L1_2$ phase, the $Al_2Ti$ phase forms on the {100} planes of the $L1_2$ matrix lattice. After prolonged aging the precipitates are rearranged along a preferential direction of the matrix lattice and form a domain consisting of only one variant. It is suggested that the precipitation of $Al_2Ti$ in each matrix alloy occurs to form a morphology which efficiently relaxes the elastic strain between precipitate and matrix lattices.

Improvement of Output Linearity of Matrix Converters with a General R-C Commutation Circuit

  • Choi, Nam-Sup;Li, Yulong;Han, Byung-Moon;Nho, Eui-Cheol;Ko, Jong-Sun
    • Journal of Power Electronics
    • /
    • 제9권2호
    • /
    • pp.232-242
    • /
    • 2009
  • In this paper, a matrix converter with improved low frequency output performance is proposed by achieving a one-step commutation owing to a general commutation circuit applicable to n-phase to m-phase matrix converters. The commutation circuit consists of simple resister and capacitor components, leading to a very stable, reliable and robust operation. Also, it requires no extra sensing information to achieve commutation, allowing for a one-step commutation like a conventional dead time commutation. With the dead time commutation strategy applied, the distortion caused by commutation delay is analyzed and compensated, therefore leading to better output linear behavior. In this paper, detailed commutation procedures of the R-C commutation circuit are analyzed. A selection of specific semiconductor switches and commutation circuit components is also provided. Finally, the effectiveness of the proposed commutation method is verified through a two-phase to single-phase matrix converter and the feasibility of the compensation approach is shown by an open loop space vector modulated three-phase matrix converter with a passive load.

VARIATIONS OF CONTAMINANT RETARDATION FACTOR IN THE PRESENCE OF TWO MOBILE COLLOIDS

  • Kim, Song-Bae;Kim, Dong-Ju
    • 한국지하수토양환경학회:학술대회논문집
    • /
    • 한국지하수토양환경학회 2001년도 추계학술발표회
    • /
    • pp.115-119
    • /
    • 2001
  • Contaminant retardation factor is derived from the colloidal and contaminant transport equations for a four-phase porous medium: an aqueous phase, two mobile colloidal phases, and a solid matrix. It is assumed that the contaminant sorption to solid matrix and colloidal particles and the colloidal deposition on solid matrix follow the linear isotherms. The behavior of the contaminant retardation factor in response to the change of model parameters is examined employing the experimental data of Magee et al. (1991) and Jenkins and Lion (1993). In the four-phase system, the contaminant retardation factor is determined by both the contaminant association with solid matrix and colloidal particles and the colloidal deposition on solid matrix. The contaminant mobility is enhanced when the affinity of contaminants to mobile colloids increases. In addition, as the affinity of colloids to solid matrix decreases, the contaminant mobility increases.

  • PDF

Zr-V-Mn-Ni계 라브스상 합금의 미세 구조와 전기 화학적 특성 (The Microstructure and the Electrochemical Characteristics of Zr based Zr-V-Mn-Ni Laves Phase Alloy)

  • 정치규;한동수;정원섭;김인곤;김원백
    • 한국수소및신에너지학회논문집
    • /
    • 제8권3호
    • /
    • pp.121-129
    • /
    • 1997
  • 아크 용해법으로 제작한 $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ 합금(bulk 합금) 잉고트는 $ZrV_{0.2}Mn_{0.98}Ni_{1.04}$의 조성식을 가지는 fcc 구조의 C15형 Laves상이 주류를 이루는 matrix와 $ZrV_{0.01}Mn_{0.13}Ni_{1.2}$의 조성으로 $Z_9Ni_{11}$의 금속간 화합물 구조를 가지는 2nd phase가 균일하게 분포된 2개의 상으로 구성되어 있었다. $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ 합금의 방전 특성에 이 두 가지 상들이 미치는 영향을 알아보기 위해서 matrix와 2'nd phase합금을 분리 제작하였고, 이들 전극에 대한 전기 화학적인 충방천 특성들을 조사하였다. 그 결과 방전용량은 2nd phase가 가장 낮은 $160mAh/g$, 그 다음으로 matrix가 200mAh/g으로 bulk의 250mAh/g보다 낮았다. Matrix조성의 합금은 bulk합금과 거의 유사한 활성화, 고율 방전율, 자기방전 특성을 가졌고, 또한 활성화 후에 충방전에 따른 용량감소의 경향이 현저히 관찰되었다. 그러나 2nd phase 조성의 합금은 이들과는 확연한 차이를 보였다. 즉 활성화되기 어렵지만 활성화된 후에 용량감소의 경향은 거의 없었고 또한 자기방전 특성도 우수하였다.

  • PDF