• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.97-104
• /
• 2010

The materials failure relation $\ddot{\Omega}=A{(\dot{\Omega})}^\alpha$ where $\Omega$ is a measurable quantity such as displacement and the dot superscript is the time derivative, may be used to analyze the accelerating creep of materials. Coefficients, A and $\alpha$, are determined by fitting given data sets. In this study, it is tried to predict the failure time of tunnel using the materials failure relation. Four fitting techniques of applying the materials failure relation are attempted to forecast a failure time. Log velocity versus log acceleration technique, log time versus log velocity technique, inverse velocity technique are based on the linear least squares fits and non-linear least squares technique utilizes the Levenberg-Marquardt algorithm. Since the log velocity versus log acceleration technique utilizes a logarithmic representation of the materials failure relation, it indicates the suitability of the materials failure relation applied to predict a failure time of tunnel. A linear correlation between log velocity and log acceleration appears satisfactory(R=0.84) and this represents that the materials failure relation is a suitable model for predicting a failure time of tunnel. Through comparing the real failure time of tunnel with the predicted failure times from four curve fittings, it is shown that the log time versus log velocity technique results in the best prediction.

• Journal of Applied Reliability
• /
• v.16 no.2
• /
• pp.104-109
• /
• 2016

Purpose: The purpose of this study is to analyze fracture behavior and failure mechanism of porous titanium for dental implant fabricated by space holder process. Method: Three porous titanium specimens with a specific volume fraction of open pore were test by 3 point bending and compression stress condition, respectively. Fracture appearance was observed by scanning electron microscope and discussed in relation with oxygen content. Results: For compression-tested specimens, two specimen showed brittle failure, while the other one showed normal failure after deformation. High oxygen content was detected in the brittle-fractured specimen. Several micro-cracks initiated at the struts propagated down to the bottom of the specimen resulting in normal failure. Conclusion: Oxygen contamination during the fabrication process can leads brittle premature failure, and hence quality problem of the porous titanium for dental implant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.393-401
• /
• 2021

In this paper, we proposed a numerical model based on moment-curvature, to evaluate the resistance of reinforced concrete (RC) members subjected to blast loading. To consider the direct shear failure mode, we introduced a dimensionless spring element based on the empirical direct shear stress-slip relation. Based on the dynamic increase factor equations for materials, new dynamic increase factor equations were constructed in terms of the curvature rate for the section which could be directly applied to the moment-curvature relation. Additionally, equivalent bending stiffness was introduced in the plastic hinge region to consider the effect of bond-slip. To verify the validity of the proposed model, a comparative study was conducted against the experimental results, and the superiority of this numerical model was confirmed through comparison with the analytical results of the single-degree of freedom model. Pressure-impulse (P-I) diagrams were produced to evaluate the resistance of members against bending failure and direct shear failure, and additional parametric studies were conducted.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.787-790
• /
• 2000

This paper presents an experimental study on flexural behavior of structural member enlarged with epoxy mortar system. The main test variable is flexural tensile strength. A series of 4 test beams was tested to shoe the corresponding effect of each variables on maximum load capacity, load-deflection and moment-curvature relationship, interface behavior and failure mode. The results show that the flexural tensile strength of retrofitted materials have no relation load-deflection, but to load-strain, and failure mode.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.268-271
• /
• 1999

Fatigue life Prediction is investigated analytically based on the fatigue modulus concept. Fatigue modulus degradation rate at any fatigue cycle was assumed as a power function of number of fatigue cycles. New stress function describing the relation of initial fatigue modulus and elastic modulus was used to account for material non-linearity at the first cycle. It was assumed that fatigue modulus at failure is proportional to applied stress level. A new fatigue life prediction equation as a function of applied stress is proposed. The prediction was verified experimentally using cross-ply carbon/epoxy laminate (CFRP) tube.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1181-1185
• /
• 1990

A failure evaluation diagram to evaluate fatigue fracture was developed. The relation between the fatigue limit and the threshold stress intensity factor for the short-cracked specimens of various materials including a piping carbon steel can be rationally predicted by the proposed method. It is shown that the coupled failure evaluation diagram for fatigue and ductile fracture is expecially useful for evaluation of the flaw tolerance as well as the margin of the safety of the pressure vessel and piping. Further, accumulation of fatigue data will be needed to construct an accurate fatigue failure evaluation diagram.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.59-65
• /
• 2000

Most studies of failure analysis in ductile metals have been based on the classical plasticity theory using the local constitutive relations. These frequently yields a physically unrealistic solution, in which a numerical prediction of the onset of a deformation localization shows an inherent mesh-size sensitivity. A one way to remedy the spurious mesh sensitivity resulted in the unreasonable results is to incorporate the non-local plasticity into the simulation model, which introduce an internal (material) length-scale parameter into the classical constitutive relations. In this paper, a non-local version of the modified Gurson constitutive relation has been introduced into the finite element formulation of the simulation for plane strain compression of the visco elastic-plastic void material. By introducing the non-local constitutive relations we could successfully removed the inherent mesh-size sensitivity for the prediction of the deformation localization. The effects of non-local constitutive relation are discussed in terms of the load-stroke curve and the strain distributions accross the shear band.

• Steel and Composite Structures
• /
• v.24 no.5
• /
• pp.615-633
• /
• 2017

Fatigue crack initiated in welded tubular joints due to cyclic loading may produce harmful effect on the integrity of the tubular structures. To study such effect, both fatigue and static tests on nine circular tubular T-joint specimens made of carbon steel materials were carried out. The specimens were subjected to tensile loading in both fatigue and static tests. The load-displacement relation, the crack propagation and the failure mode of the specimens are all analyzed. The deterioration of the static strength of the cracked T-joints is also investigated and evaluated through an area reduction factor. Experimental results indicate that the static strength of a tubular T-joint with a surface crack seems to decrease slightly while a through crack has relatively remarkable effect on the reduction of the static strength. Additionally, experimental results also show that the toughness of the materials and the geometry of the specimens play an important role on the failure process of cracked tubular T-joints.

• Journal of Power System Engineering
• /
• v.18 no.1
• /
• pp.76-83
• /
• 2014

This study was carried out an experimental and finite element analysis on the fracture behavior of straight pipes with local wall thinning under internal pressure. Local wall thinning was machined on the pipes in order to simulate erosion/corrosion metal loss. The configurations of the eroded area has an eroded ratio of d/t=0.80~0.92 and an eroded length of l=25, 50 and 102 mm. Three-dimensional elastic-plastic analyses were also carried out using the finite element method, which is able to accurately simulate failure behaviors. In regards to the relation ship between pressure and eroded ratio, the criterion that can be used safely under operating pressure and design pressure were obtained from this calculation. The results of this calculation were in relatively good agreement with that of the experiment.

• Composites Research
• /
• v.34 no.2
• /
• pp.101-107
• /
• 2021

Composite structures have components and joints. Theses connections or joints can be potentially weak points in the structure. The failure mode of the composite bolted joint is designed as a bearing failure mode for structural safety. The load-displacement relation exhibits bearing failure mode shows a nonlinear behavior after the initial failure and progressive failure behavior. In order to accurately predict the failure behavior of composite bolted joints, this study modified the shear damage variable calculation process in the existing progressive failure analysis model. The results of the bearing stress-bearing strain of the composite bolted joint were predicted using the modified progressive failure analysis model, and the modified model was verified through comparison with the previous progressive analysis model.