• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.305-312
• /
• 2023

Purpose: Although the damage caused by abnormal temperatures is extensive, blow-up or black ice is typical in concrete structures. In this study, PCM with high phase change energy was mixed with concrete to reduce temperature damage to concrete pavement. Method: In order to reduce temperature damage to low temperatures and high temperatures, capsule-type PCM with phase change temperatures of 4.5℃ and 44℃ was replaced by 10%, 30%, and 50%, and thermal performance experiments and compressive strength experiments were conducted using thermocouples and variable chambers. Result: As a result of the thermal performance experiment, it was found that the incorporation of PCM improves temperature resistance by up to 25% or more, and increases thermal resistance at all temperatures with high specific heat when substituted in large amounts. As a result of the compression strength experiment, a substitution of 30% or more resulted in a decrease in the compression strength, and a large strength difference was shown based on the phase change temperature of the PCM. Conclusion: The incorporation of PCMs has been shown to increase the thermal performance of concrete, with the greatest increase in thermal performance near the phase change temperature of PCM. In addition, a small strength reduction of 10% to 20% occurs at the highest substitution rate of 50% substitution, so there is no significant problem with usability, and additional PCM substitution is expected to improve thermal performance.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.99-107
• /
• 2007

The linear curve fitting methods such as the Hvorslev method and the Bouwer and Rice method provide a rapid and simple means to analyze slug test data for estimating in-situ hydraulic conductivity (k) of geologic material. However, when analyzing a slug test in a relatively compressible aquifer, these methods have difficulties in fitting a straight line to the semi-logarithmic plot of the test data that shows a concave-upward curvature because the linear curve fitting methods ignore the role of the compressibility or specific storage ($S_s$) of an aquifer. The comparison of the Hvorslev method and the Bouwer and Rice method is made far a partially-penetrating well geometry to show analytically that the Hvorslev method estimates higher hydraulic conductivity than the Bouwer and Rice method except that the well intake section locates very close to the bottom of the aquifer. The effect of fitting a straight line to the slug test data is evaluated along with the dimensionless compressibility parameter (${\alpha}$) ranging from 0.001 to 1. A modified linear curve fitting method that is expanded from Chirlin's approach to the case of a partially penetrating well with the basic-time-lag fitting method is introduced. A case study for a compressible glacial till is made to verify the proposed method by comparing with a type curve method (KGS method).

• Journal of Environmental Health Sciences
• /
• v.48 no.1
• /
• pp.1-8
• /
• 2022

Objectives: The purpose of this study is to reveal the circumstances under which the cases of harm to health caused by humidifier disinfectant were neglected and show the points where the number of victims and the degree of damage could have been reduced. In addition, it attempts to describe how damage management proceeded immediately after the incident and actually exacerbated the damage. Finally, it explores the unfortunate aspects of the recent trial. By doing so, it attempts to take this as an opportunity to consider whether a tragic event such as the humidifier disinfectant incident could occur in the future. Methods: This study collected and analyzed data on chemical material characteristics related to humidifier disinfectants, data on health effect characteristics, data on related laws and regulations from the Ministry of Environment, data related to the damage investigation by the Korea Environmental Industry and Technology Institute, and current contents. Results: The lack of related systems and laws is the area where the greatest responsibility for the cause of the humidifier disinfectant disaster falls, so it is difficult for the government to escape this responsibility. Establishing a dedicated department to identify the prevalence of certain diseases within the functions of the Health Insurance Review and Assessment Service to monitor health can greatly contribute to the prevention and management of diseases through early detection and management of group outbreaks caused by harmful factors. Humidifier disinfectant damage relief should have been expanded earlier beyond HDLI (humidifier disinfectant lung injury) to include non-specific diseases such as asthma, pneumonia, and interstitial pneumonia. The scope of relief benefits should have also been expanded earlier to include the payment of disability benefits. Fortunately, with the 2020 revision of the Special Act, the conditions for estimating causal relations were eased and individual screening systems such as health impact assessment were reorganized along with the introduction of a rapid screening system. Conclusions: The management system for chemical substances in a country is clearly of paramount importance, and the ministry in charge must have a response system in case of damage to health effects. Administration that looks at the victims' situation from their point of view is needed, and technical countermeasures are required to quickly recognize the prevalence of certain diseases.

• Journal of the Korean Society of Floral Art and Design
• /
• no.41
• /
• pp.115-132
• /
• 2019

Today, the expansion of the possibility of new expressions of plastic arts is largely due to emergence and application of new materials. In the field of flower design, it is found that there is a tendency to seek a new expression by utilizing various new materials instead of natural material that used in the past. This study is an attempt of applying methodological approach in the creation of floral art works utilizing the characteristics of contemporary materials in such context. The researcher gathered cases of specific effect and sensation in the expression of art works using various contemporary materials and extracted the characteristics using descriptive sentences applying behavior setting analysis technique. Reporting detailed result of the research total 100 guidelines under 41 sub-categories, 24 mid-categories, and 6 top categories such as transparency, lighting, combination of objects, combination of materials, reflection, shape construction. The researcher tested the effectiveness of the theories by applying deducted theories as the guidelines in creation process of her own floral art works. The significance of this study lies at experimenting the possibilities of applying methodological approach which could supplement intuitive approach in pursuit of expression for artists in the field of floral art and design.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.2
• /
• pp.437-444
• /
• 2017

Stress concentrations around discontinuities, such as a hole in cross section of a structural member, have great importance because the most materials failure around the region may be occurred. Stress on the point applied by concentrated load reaches much larger value than the average stress in structural member. In this paper, stress analysis was performed for the plate with a partial through-hole to find the difference of the principal stress distribution. The difference between maximum principal stress and minimum principal stress in photoelasticity is equal to the value obtained by multiplying the isochromatic fringe order by the fringe constant of the material divided by the distance through which the light passes, that is, the thickness of the specimen. Since the difference of principal stress is proportional to the photoelastic fringe order, the distribution of the principal stress difference by the finite element analysis can be compared with the photoelasticity experimental result. ANSYS Workbench, that is the finite element software, is used to compute the differences of principal stresses at the specific points on the measured lines. The computation values obtained by ANSYS are compared with the experimental measurements by photoelasticity, and two results are comparable to each other. In addition, the stress concentration factor is obtained using the stress distribution analyzed from the variation of hole depth. Stress concentration factor is increasing, as the depth of hole increase.

• Journal of Bio-Environment Control
• /
• v.32 no.3
• /
• pp.181-189
• /
• 2023

Hydrogen has gained attention as an environmentally friendly energy source among various renewable options, however, its application in agriculture remains limited. This study aims to apply the hydrogen fuel cell triple heat-combining system, originally not designed for greenhouses, to greenhouses in order to save energy and reduce greenhouse gas emissions. This system can produce heating, cooling, and electricity from hydrogen while recovering waste heat. To implement a hydrogen fuel cell triple heat-combining system in a greenhouse, it is crucial to evaluate the greenhouse's heating and cooling load. Accurate analysis of these loads requires considering factors such as greenhouse configuration, existing heating and cooling systems, and specific crop types being cultivated. Consequently, this study aimed to estimate the cooling and heating load using building energy simulation (BES). This study collected and analyzed meteorological data from 2012 to 2021 for semi-enclosed greenhouses cultivating tomatoes in Jeonju City. The covering material and framework were modeled based on the greenhouse design, and crop energy and soil energy were taken into account. To verify the effectiveness of the building energy simulation, we conducted analyses with and without crops, as well as static and dynamic energy analyses. Furthermore, we calculated the average maximum heating capacity of 449,578 kJ·h^-1 and the average cooling capacity of 431,187 kJ·h^-1 from the monthly maximum cooling and heating load analyses.

• Journal of Service Research and Studies
• /
• v.11 no.3
• /
• pp.75-97
• /
• 2021

This study was conducted to derive a society and education system model that will improve the happiness and sustainability of human society. An ideological model for making human society a happy society was derived, and a society and education system structure and operation model based on this was presented. A fair society, a justice society, a mutually considerate society, and a society where individuals are happy are the conditions for a sustainable society. After analyzing the current situation of freedom and equality pursued by capitalism and democracy, which are currently adopted by most societies, an improvement model was derived from the perspective of a sustainable society. The cost of freedom and equality were analyzed and a new alternative system was discussed. The social solidarity and class mobility issues were discussed together and servicism was derived as an alternative solution. It is a system in which two opposing opponents of individual freedom and social norms form a symmetrical balance, and material and spiritual values are balanced. Servicism is a dynamic balance model. That is, the dimensions of time and space are involved. It is a model that maintains a thorough balance through a dialectical process as time and space change, and one value can dominate the other at a specific time or space. The service-oriented society and education system is a system that simultaneously pursues the goals of individual happiness and sustainable development of the social community.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.191-203
• /
• 2006

The vibration characteristics of composite stiffened laminated plates with stiffener is presented using the assumed natural strain 9-node shell element. To compare with previous research, the stiffened plates are composed of carbon-epoxy composite laminate with a symmetric stacking sequence. Also, the result of the present shell model for the stiffener made of composite material is compared with that of the beam model. In the case of torsionally weak stiffener, a local buckling occurs in the stiffener. In this case, the stiffener should be idealized by using the shell elements. The current investigation concentrates upon the vibration analysis of rectangular stiffened and unstiffened composite plates when subjected to the in-plane compression and shear loads. The in-plane compression affect the natural frequencies and mode shapes of the stiffened laminated composite plates and the increase in magnitude of the in-plane compressive load reduces the natural frequencies, which will become zero when the in-plane load is equal to the critical buckling load of the plate. The natural frequencies of composite stiffened plates with shear loads exhibit the higher values than the case of without shear loads. Also, the intersection, between the curves of frequencies against in-plane loads, interchanges the sequence of some of the mode shapes as a result of the increase in the inplane compressive load. The results are compared with those available in the literature and this result shows that the present shell model for the stiffened plate gives more accurate results. Therefore, the magnitude, direction type of the in-plane shear and compressive loads in laminated composite stiffened plates should be selected properly to control the specific frequency and mode shape. The Lanczos method is employed to solve the eigenvalue problems.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.1C
• /
• pp.45-51
• /
• 2010

In urban area, design and construction of civil engineering structures such as subway tunnel, underground space and deep excavation is impeded by unreliable site investigation. Variety of embedded objects, electric noises and traffic vibrations degrades the quality of site investigation, whatever the site-investigation technique would be. In this research, a preliminary research was performed to develop a dedicated site investigation technique for urban geotechnical sites, which can overcome the limitations of urban sites. HiRAS (Hybrid Integration of Surface Waves and Resistivity) technique which is the first outcome of the preliminary research was proposed in this paper. The technique combines surface wave as well as electrical resistivity. CapSASW method for surface-wave technique and PDC-R technique for electrical resistivity survey were incorporated to develop HiRAS technique. CapSASW method is a good method for evaluating material stiffness and PDC-R technique is a reliable method for determination of underground stratification even in a site with electrical noise. For the inversion analysis of HiRAS techniuqe, a site-specific relationship between stress-wave velocity and resistivity was employed. As for outgrowth of this research, the 2-D distribution of Poisson's ratio could be also determined.

• Smart Media Journal
• /
• v.12 no.5
• /
• pp.36-45
• /
• 2023

Recently, in digital agriculture, the types and utilization of greenhouses based on IoT are spreading, and greenhouses are being modernized, enlarged, and even factoryized using smart technology. However, a specific standardization plan has not been proposed according to the equipment for data collection in the smart greenhouse and the size or shape of the greenhouse. In other words, there is a lack of standard data for facility equipment, such as the type and number of sensors and equipment according to the size of the greenhouse, the type of greenhouse construction film and materials suitable for crops and carbon neutrality. Therefore, in this study, the suitability of the implementation, installation and quantity of IoT equipment for data collection was tested, and some standard technologies were presented through the implementation of data collection and communication methods. In addition, impact strength, tensile, tear, elongation, light transmittance, and lifespan issues for PE, PVC, and EVA, which account for about 90% of existing greenhouses, were presented, and the shape, size, and environmental problems of greenhouses made of films were presented. presented in the text. In this research paper, a standardized carbon-neutral modular smart greenhouse using nano-material film was implemented as a solution to environmental problems such as greenhouse size, farm crop type, greenhouse lifespan, and film, and its performance with existing greenhouses was analyzed and presented. Through this, we propose a modularized greenhouse that can be expanded or reduced freely without distinction in the size of the greenhouse or the shape of farmhouse crops, and the lifespan is extended and standardized. Finally, the average characteristics of greenhouses using existing PE, PVC, and EVA films and the characteristics of greenhouses using new carbon-neutral nanomaterials are compared and reviewed, and a plan to implement an expandable IoT greenhouse that supports carbon neutrality is proposed.