• Restorative Dentistry and Endodontics
• /
• v.45 no.2
• /
• pp.11.1-11.9
• /
• 2020

Objectives: This study compared the flow and filling of several retrograde filling materials using new different test models. Materials and Methods: Glass plates were manufactured with a central cavity and 4 grooves in the horizontal and vertical directions. Grooves with the dimensions used in the previous study (1 × 1 × 2 mm; length, width, and height respectively) were compared with grooves measuring 1 × 1 × 1 and 1 × 2 × 1 mm. Biodentine, intermediate restorative material (IRM), and mineral trioxide aggregate (MTA) were evaluated. Each material was placed in the central cavity, and then another glass plate and a metal weight were placed over the cement. The glass plate/material set was scanned using micro-computed tomography. Flow was calculated by linear measurements in the grooves. Central filling was calculated in the central cavity (㎣) and lateral filling was measured up to 2 mm from the central cavity. Results: Biodentine presented the least flow and better filling than IRM when evaluated in the 1 × 1 × 2 model. In a comparison of the test models, MTA had the most flow in the 1 × 1 × 2 model. All materials had lower lateral filling when the 1 × 1 × 2 model was used. Conclusions: Flow and filling were affected by the size of the test models. Higher grooves and materials with greater flow resulted in lower filling capacity. The test model measuring 1 × 1 × 2 mm showed a better ability to differentiate among the materials.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.42-47
• /
• 2012

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. We have discussed the influences of tool geometry such as punch nose angle, relative gap height, die corner radius on material flow and surface expansion into can and flange region. To analyse the process, numerical simulations by the FEM and experiment by physical modeling using Al alloy as a model material have been performed. Based on the results, the influence of fixed parameters on the distribution of divided material flow and surface expansion are obtained.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.251-258
• /
• 2003

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. The paper discusses the influences of tool geometry such as punch nose angle, relative gap height, die comer radius on material flow and surface expansion into can and flange region. To analyze the process, numerical simulations by the FEM and experiment, an Al alloy as a model material have been performed. Based on the results, the influence of design parameters on the distribution of divided material flow and surface expansion are obtained.

• International Journal of Highway Engineering
• /
• v.19 no.4
• /
• pp.19-25
• /
• 2017

PURPOSES : In this paper, the flow of construction material was simulated using computational fluid dynamics in a 2D axisymmetric condition to evaluate the effect of initial or varying material properties on the final shape of a specimen. METHODS : The CFD model was verified by using a well-known analytical solution for a given test condition followed by performing a sensitivity analysis to evaluate the effect of material properties on the final shape of material. Varying dynamic viscosity and yield stress were also considered. RESULTS : The CFD model in a 2D axisymmetric condition agreed with the analytical solution for most yield stress conditions. Minor disagreements observed at high yield stress conditions indicate improper application of the pure shear assumption for the given material behavior. It was also observed that the variation of yield stress and dynamic viscosity during curing had a meaningful effect on the final shape of the specimen. CONCLUSIONS : It is concluded that CFD modeling in a 2D axisymmetric condition is good enough to evaluate fluidal characteristics of material. The model is able to consider varying yield stress and viscosity during curing. The 3D CFD-DEM coupled model may be required to consider the interaction of aggregates in fluid.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.859-863
• /
• 1995

Presented in the paper are a review of sorting and buffering system(SBS), the design procedure of a SBS and an analytical model for the initial alternative generation. SBS is an automated material handling system in which incoming items of different part types are automatically sorted and buffered so that the processing machines can process the part in lots. SBSs play a key role in modern manufacturing systems ans are widely found in mass fabrication lines, packaging and palletizing, and disribution centers.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.120-125
• /
• 2004

In the rolling of steel or non-steel metal the most important quality aspect are thickness and flatness. In thickness, there are two important factors. One of them is getting close with accurate goal, nominal gauge, the other is minimize gauge bandwidth, the variation in gauge. In this thesis, we proposed the fuzzy model AGC to minimize gauge variation along the length, developed the rolling mill dynamic model using the math mode of the rolling mill process and the rolling model related with the variety character of the rolling material. We compared the gauge control efficiency of fuzzy model AGC and PI mass flow AGC. We have got a simulation result, that the exit gauge variation of PI mass flow AGC was 2 micron and fuzzy model AGC was 1.2 micron at 1200mpm of rolling speed when each controller was rolling 5 micron of material that is the entry gauge variation.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.49 no.5
• /
• pp.3-9
• /
• 2007

In this study, the effect of the purification materials is analyzed and tested by Flow 3D and Hydraulic model test. Three dimension numerical analysis led from the research that sees abnormal form and the size back of the water purification material conferred the flowing water conduct inside the test channel against the test condition. Comparison it analyzed the flux distribution, a water depth of the channel which establishes the water purification materials the cross section, an interval of the water purification material, a conference with general channel, it change executed. As a result, the cross section ratio of the purification materials against and a flux change from the test which it sees. The interval of the purification materials in order to prevent three dimension that follows in decrease of increase and flux must decide an interval.

• Journal of Korean Association for Spatial Structures
• /
• v.2 no.3 s.5
• /
• pp.103-113
• /
• 2002

This thesis investigates vibration response characteristics of building frames in which dampers are installed. The frames belong to passively vibration-controlled. Structures which utilizes energy dissipation of mechanical dampers provided in the structure. In this thesis, a turbulent flow damper sealed by visco-elastic material was dealt with as the device of passive vibration control. To investigate the resisting force characteristics of the damper, harmonic vibratration tests were carried out. Based on the test results, a theoretical model of the damper resistance was presented and a method of identifying the model parameters was proposed. Shaking table tests of the frame with and without the dampers were carried out and the effectiveness of the damper was examined. The response of the frame with the dampers was reduced to 1/2 or 1/3 of the cases without the damper.

• Fibers and Polymers
• /
• v.2 no.1
• /
• pp.140-143
• /
• 2001

To better understand the formation of necking in drawing processes of fibers, strain distributions during drawing processes have been analyzed. For simplicity, one-dimensional incompressible steady flow at a constant temperature was assumed and quasi-static model was used. To describe mechanical properties of solid polymers, non-linear visco-plastic material properties were assumed using the power law type hardening and rate-sensitive equation. The effects of various parameters on the neck formation were matematically analyzed. As material property parameters, strain-hardening parameter, visco-elastic coefficient and strain-rate sensitivity were considered and, for process parameters, the drawing ratio and the process length were considered. It was found that rate-insensitive materials do not reach a steady flow state and the rate-sensitivity plays a key role to have a steady flow. Also, the neck formation is mainly affected by material properties, especially for the quasi-static model. If the process length changes, the strain distribution was found to be proportionally re-distributed along the process line by the factor of the total length change.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1271-1274
• /
• 2009

One of the landslide, Debris flow means flow mixed of rocks, gravels, sand and soil with water. Debris flow occurred in summer by passed the rainy season and typhoon. Especially, Localized heavy rain derived from abnormal weather caused debris flow independent of season. It is increase to collapse of house, bridge, roads by debris flow but countermeasure studies about occurrence cause, movement pattern, damage scale about debris flow are insufficient. This study performed debris flow model experiment using dry material and calculated shock force predicted debris flow occurrence.