• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.43-44
• /
• 2005

SU-8 is a epoxy based photoresist designed for MEMS applications, where a thick, chemically and thermally stable image is desired. But SU-8 has proven to be very sensitive to variation in processing variables and hence difficult to use in the fabrication of useful structures. In this paper, negative SU-8 photoresist processed has been characterized in terms of delamination. Based on a full factorial designed experiment. Employing the design of experiment (DOE), a process parameter is established, and analyzing of full factional design is generated to investigate degree of delamination associated with three process parameters: post exposure bake (PEB) temperature, PEB time, and exposure energy. These results identify acceptable ranges of the three process variables to avoid delamination of SU-8 film, which in turn might lead to potential defects in MEMS device fabrication.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.72-78
• /
• 2010

Textile machinery affects various industry, such as sport leisure industry, metal and chemistry material, electric electron, mechanical energy, packing and printing industry. In case of design of textile machine, the very important fact is absorbing the minute vibration induced by spinning thread and insert which is the part of spindle plays a role of reduction of impact caused by oscillation of thread bobbin. Therefore, Optimal design was executed by design of experiments and kriging optimal design methods to prevent fracture of spindle insert under the fatigue condition and deduced the best value of design parameter to improve the stability of the products. The highest sensitivity is showed at the design parameter A and D. As the spiral number of insert is increase, tension force applied its edge is distributed at whole model and the stress concentration is reduced.

• Tribology and Lubricants
• /
• 제23권3호
• /
• pp.103-108
• /
• 2007

In this paper, the optimized design and strength analysis have been presented based on the finite element and Taguchi's experimental methods. The stress, strain and displacement characteristics of OPC drum tubes are affected by rolling contact pressures between an OPC drum tube and a paper, design parameters of an aluminum tube and material properties. The OPC drum tubes with nine different geometrical models are analyzed for design parameters that are related to the outer diameter, the thickness, and the length of an aluminum tube for a toner cartridge. The optimized design parameters for an aluminum tube may be selected as the outer diameter of 28 mm, the thickness of 0.8 mm, and the length of 220 mm. But the currently used aluminum tube for a laser printer is fairly optimized based on the Taguchi's design analysis. The calculated FEM results showed that the affection ratio of the design parameter t, which may control the strength of an aluminum tube, is the most influential parameter among the length and an outer diameter of a tube.

• 한국물환경학회지
• /
• 제28권1호
• /
• pp.109-114
• /
• 2012

In this study, both sedimentation and thickening experiments were conducted for residuals produced from an advanced water treatment plant for more accurate and practical design of residual treatment train. In order to design a backwashed residual sedimentation basin (SRSB) in the filter backwash water recycle system, two kinds of backwash waters, one from sand filter (SFBW) and the other from GAC adsorption bed (GACBW), were separately collected and their surface loading rate measured. In addition, in order to design a gravity thickener, batch thickening tests were conducted for concentrated residuals taken from sedimentation basin and their limiting solid flux ($SF_{L}$) measured. From the experimental results and consideration of the seasonal characteristics of the residual, surface loading rate of $70m^{3}/m^{2}{\cdot}d$ was proposed as a design parameter for SRSB and solid loading rate of 20 kg $TS/m^{2}{\cdot}d$ was proposed as a design parameter for gravity thickeners. Finally, the material mass-balance was made for the design of each unit process in the residual treatment train.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.322-325
• /
• 2000

In the previous report1), the grinding characteristics of quartz were investigated. In this paper, the grinding mechanisms of brittle materials including ceramics and quartz are modeled and a new parameter SDR(Surface roughness Direction Ratio) is proposed to characterize the grinding mechanisms of such materials. A set of experiments were performed to verify the effectiveness of the suggested parameter. The experimental results indicate that the plastic deformation is the dominant material removal mode at the grinding conditions which show the higher value of SDR. In the case of quartz, the material was removed by brittle fracture in a lower value of SDR and by plastic deformation in a higher value of it. SDR is not affected by wheel mesh size when brittle fracture occured. But in the plastic deformation case, SDR value increases with wheel mesh size.

• 수산해양기술연구
• /
• 제29권2호
• /
• pp.152-161
• /
• 1993

This paper deals with the effect of spatial distribution of material properties on its statistical characteristics and numerical estimation method of reliability of fatigue sensitive structures with respect to the fatigue crack growth. A method is proposed to determine experimentally the probability distribution functions of material parameters of Paris law. da/dN=C(ΔK/K sub(0) ) super(m), using stress intensity factor controlled fatigue tests. The result with a high tensile strength steel shows that the distribution of the parameter m is approximately normal and that of 1/C, is a 3-parameter Weibull. The main result obtained are : (1) The theoretical autocorrelation of the resistance, 1/C, to fatigue crack growth are almost same for different lengths. (2) The variance decreases with the increasing a averaging length. When spatial correlation length is very small. the variane decreases significantly were the averaging length. (3) The probability distribution of load cycles or the number for a crack to reach a certain length can be estimated using these functions by simulation of non-Gaussian(expecially Weibull) Stochastic Process.

• 한국전산구조공학회논문집
• /
• 제36권4호
• /
• pp.259-264
• /
• 2023

본 논문에서는 3차원 엮임 재료의 재료 물성치들을 효율적으로 분석하고 추후 최적설계 연구에 활용하기 위해서 파라메트릭 배치 해석 워크플로우를 제시하였다. 3차원 엮임 재료를 구성하는 와이어들 사이의 간격을 설계 매개변수로 하는 파라메트릭 모델에 대해서 임의의 변수 조합을 가지는 2,500개의 수치 모델을 생성하였으며, 상용 프로그램인 매트랩과 앤시스의 여러 모듈을 사용하여 체적탄성계수, 열전도도, 유체투과율과 같은 다양한 재료 물성치들을 배치 해석을 통해서 자동으로 얻어질 수 있도록 구성하였다. 이와 같이 얻어진 대용량의 재료 물성치 데이터베이스를 활용해서 회귀 분석을 수행하였으며, 그 결과 설계 변수들과 재료 물성치 사이의 경향성과 수치 해석 결과의 정확도를 검증하였다. 또한 확보된 데이터베이스를 통해서 3차원 엮임 재료의 물성치를 예측할 수 있는 인공 신경망을 구성하고 학습시켰으며, 그 결과 임의의 설계 매개변수 값들을 가지는 엮임 재료 모델에 대해서 구조 및 유체해석 과정 없이도 높은 정확도로 재료 물성치들을 추정할 수 있음을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.279-284
• /
• 2007

Elasto-forming has been dedicated to specific and limited production. Today, using enhanced pad materials, it has become an efficient and economical process alternative for low and medium volume metal-forming production. The non-linear properties of elastomer which are described as strain energy function are important parameter to design and evaluate of elastomer component. These are determined by material tests which are uni-axial tension and bi-axial tension. In order to investigate the design paramerer, Finite element analysis was carried out for elasto-forming process.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.127-131
• /
• 2008

This paper deals with the performance evaluation of piezoelectric unimorph actuator. In the unimorph design, the thickness ratio of substrate to piezoelectric material and the elastic modulus ratio of substrate to piezoelectric material are important parameters. There exists only one structural configuration that satisfies the optimal condition among them, and actuators using that configuration exhibit better actuating displacements. Another design parameter is the piezoelectric coefficient which can be improved due to the induced tensile stress and voltages. The application of the tensile stress to the piezoelectric material makes it get higher piezoelectric coefficient and the total displacement performance of the unimorph actuator is improved. Finally, the piezoelectric actuator system with spring elements is fabricated and it shows higher actuating displacement capability.

• 소성∙가공
• /
• 제13권7호
• /
• pp.635-641
• /
• 2004

Today the specific outputs of modern supercharger DI diesel engine for passenger cars reach values exceeding 50kw/1. By development of the articulated piston, specific output of up to 70kw/1 are sought. In doing so, peak cylinder pressure increases from the current 14-16MPa to 18-20MPa. The Articulated piston was composed Al cast skirt part and steel forged crown part. We have the target fer the design of forging process and die of the steel forged crown part. The design parameters of the forging process of the piston were obtained by the forging industry experiences and our experimental data and analysis result of finite element simulation. Especially, the design parameter of preform in blocker die was decided by finite element simulation using numerical package DEFROM3D. And also we can verify the design parameter by conducting visio-plasticity test using plasticine material. When we compared the results of analysis and experiment, a metal flow and load curve showed good agreement. Through this research, we could design optimal preform shape of articulated piston for this supercharged DI diesel engine.