• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.107-111
• /
• 2004

This work describes the effect of composite conductor on the characteristics of electric double layer capacitor. Test cell, which was fabricated with conducting composite consisted of 80％ of SPB and 20％ of VGCF, exhibits the better tate capability and the lower resistance than those of the cells fabricated with single electronic conductor. These enhanced properties could be related with the decrease of contact resistance between the activated carbon powders.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.275-278
• /
• 2000

We were fabricated of NiCr thin film resistors(TFR) on A1$_2$O$_3$(99.5%) substrates by dc magnetic sputtering system. The characteristics of electrical resistance (Sheet resistance & Temperature-Coefficient of the resistance-value:TCR) by annealing condition and reactive gas on the resistors were studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.465-467
• /
• 1997

The oscillating properties of quartz Crystal Microbalance(QCM) were analyzed by electrical measurement. We tried to analyze the properties of quartz crystal coated with Langmuir-Bladgett(LB) films using the frequency and resistance at resonance in the electrical equivalent circuit. The resonant frequency was decreased linearly as to layers of LB films, however, there are some gap between theoretical values, Sauerbrey's equation and experimental values. The resistance was increase nonlinearly as to layers.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.403-404
• /
• 2006

Sintered materials have been applied widely in Valve Seat Inserts (VSI). The demands for VSIs are not only good heat and wear resistance but also good machinability. The sintered materials, which are made of a mixture of manganese containing iron powder and certain types of sulfide powder, have superior machinability due to precipitation of the fine MnS particles in the matrix. This report introduces a new VSI material, which has both superior machinability, and wear resistance due to applies of this "MnS precipitation" technique.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.6
• /
• pp.586-595
• /
• 2012

While the extruded cement panel has many advantages compared to drywall, it has limited applicability in buildings due to its low fire resistance. However, an extruded panel in which the fire resistance has been dramatically enhanced through the addition of a-hemihydrate gypsum is expected to become widely applied as a partition wall or interior material for buildings. To ensure its applicability, certain safety requirements for use, such as the leaning load by residents, the impact by indoor articles, and the fire, need to be taken into consideration. The purpose of this study is to review the impact load resistance, horizontal load resistance, and fire resistance as required safety properties for the partition wall and interior materials of the extruded panel that includes a-hemihydrate gypsum. The results of this study show that the impact load resistance of the extruded panel that includes a-hemihydrate gypsum achieves SD grade for industrial buildings, and the horizontal impact load resistance achieves HD grade for public buildings. In addition, it provides fire-resistance for approximately 7 minutes longer than the existing extruded cement panel. Based on this result, it is confirmed the extruded panel incorporating a-hemihydrate gypsum has adequate safety properties for use as partition wall or interior material.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.29-36
• /
• 2016

Aluminum alloys have been widely used in engine materials, cold & hot-water storage vessels and piping etc., Furthermore, the aluminum alloy of AC8A have been widely used in mold casting material of engine piston for various vehicles because of its properties of temperature, wear and corrosion resistance. Therefore, it is considered that evaluation of corrosion resistance as well as wear resistance of AC8A material is also important to improve its property and to prolong its lifetime. In previous paper, the effect of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 16, 24, and 36 hrs)heat treatments to corrosion resistance and hardness were investigated using electrochemical method. In this study, in order to examine completely the effect of the tempering hours to hardness variation and corrosion resistance, the results of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 2, 4, 8 and 12hrs)heat treatments to hardness and corrosion resistance were investigated using electrochemical method. The hardness decreased with solution heat treatment compared to mold casting condition, but its value increased with tempering heat treatment. Furthermore, the corrosion resistance increased with decreasing of the hardness, and decreased with increasing of the hardness reversely. And the tempering heat treatment temperature at $190^{\circ}C$ for 8 hrs exhibited the highest value of the hardness and also indicated the highest corrosion current density. However, the values of hardness and corrosion current density was again increasingly decreased with increasing of tempering hours than 8 hrs, Consequently, it is suggested that decision of the optimum. tempering hours is very important to improve the corrosion or wear resistance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.37-40
• /
• 2005

High Performance Concrete(HPC) has been widely used in high-rise building. The HPC has several benefits including high strength, high fluidity and high durability. However. spatting is susceptible to occur in HPC and HPC also tends to be deteriorated in the side of fire resistance performance at fire. This paper focuses on the analysis of the temperature history and residual compressive strength with finishing material, in order to protect HPC from sudden-high-temperature, which is one of the main reason spatting occurs. Test results show that spalling occurs in all specimens. The most serious spalling took placed in HPC covering fire enduring spray-on material, whose covering thickness is 20mm but temperature history indicates that fire enduring spray effectively protected HPC from fire for more than 2hours. In addition, residual compressive strength ratio of HPC using fire enduring paint was more than $90\%$ of original strength, thus minimizing spatting and indicating significant fire resistance performance.

• Journal of the Korea Furniture Society
• /
• v.19 no.6
• /
• pp.447-451
• /
• 2008

This study was carried out to know the difference of vapor transmission on the thickness of Paulownia wood(Paulownia tomentosa). The behavior of moisture transmission of wood thickness direction is generally estimated by vapor permeability and vapor transmission resistance. In general, Paulownia wood is known to use of inside material for furniture making, because of the excellent ability of vapor adsorption and/or desorption. Quarter sawing Paulownia wood material is prepared and the thickness is 6.0mm, 7.0mm, 8.0mm, 9.0mm, 10.0mm, respectively. The measurement of vapor transmission were conducted by the "cup method" in accordance with JIS(Japanese Industrial Standard) Z-0208. The experiment was made in the condition of 49.8mmHg vapor pressure difference and $40^{circ}C$ at constant temperature. From the experiment results, it was considered that Paulownia wood is very stable on moisture variation and any other material conditions. In this experiment we found that the vapor permeability and vapor permeance was reduced with the increase of wood thickness to vapor direction and vapor transmission resistance and specific vapor transmission resistance was increased with the increase of wood thickness to vapor direction. Besides moisture contents of adsorption and desorption side were about 5 percent and 14 percent, respectively. Mean value was 9.5 percent and about 10 percent in dry oven method. Moisture gradient was reduced with the increase of wood thickness for a small moisture difference of adsorption and desorption side.

• Elastomers and Composites
• /
• v.31 no.1
• /
• pp.23-32
• /
• 1996

PVB was blended with PMMA in order to recycle scraped PVB material which recovered in the safety glass manufactories. The purpose of this research on PVB/PMMA blend was applied with excellent tackiness and transparency of PVB as a material of high strength to make the maximum use. Also, the blending of PVB with PMMA was aimed at the increase of impact strength of PMMA because the elastic property of PVB might decrease the brittleness of PMMA due to the lack of inner impact resistance. Izod impact resistance was propotional to increase the content of PVB, which was predominantly increased in the addition of 10phr above MBS. High rate impact resistance showed a tendency to Increase but it showed a tendency to decrease maximum load and energy if the contents of PVB increased. On the other hand total energy and ductile index showed a tendency to increase excellent impact resistance in the addition of MBS contents. As a result of observed surface of PVB/PMMA blends, the size of PVB domain increased distribution homogenuously, in the addited MBS contents increased it showed distribution homogeneously and partially a wetability.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.67-68
• /
• 2017

This paper discusses the application of civil structure use reinforcing fiber mixed with concrete to be used as protection layer of waterproofing material and root resistant layer installed in below-grade parking lot upper slab of residential building. A performance evaluation under the prescribed method outlined in KS F 4938 was used for this new material. The testing results showed that the fiber reinforcement can be used to strengthen the protection for the waterproofing material. Also, plants that were planted in June 2016 have not yet penetrated the specimens used for root resistance testing. The domestic root resistance performance testing usually covers the period of 2 years, thus further observation to make any conclusion about the root resistance property is required.