• Corrosion Science and Technology
• /
• 제13권2호
• /
• pp.48-55
• /
• 2014

Influence of annealing temperature on the microstructure and resistance to pitting corrosion of the hyper duplex stainless steel was investigated in acid and neutral chloride environments. The pitting corrosion resistance is strongly dependent on the microstructure, especially the presence of chromium nitrides ($Cr_2N$), elemental partitioning behavior and volume fraction of ferrite phase and austenite phase. Precipitation of deleterious chromium nitrides reduces the resistance to pitting corrosion due to the formation of Cr-depleted zone. The difference of PREN (Pitting Resistance Equivalent Number) values between the ferrite and austenite phases was the smallest when solution heat-treated at $1060^{\circ}C$. Based on the results of electrochemical tests and critical crevice temperature tests, the optimal annealing temperature is determined as $1060^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.198-201
• /
• 1997

The new system for identification of organic vapours and analysis method of mechanism between organic vapours and sensitive materials were attempted using the resonant resistance and resonant frequency of Quartz Crystal Analyzer (Q. C. A.). The resonant resistance shift means rheological changes in sensitive LB films occurred by the adsorption of organic vapours, while the resonant frequency shift represent the mass of organic vapour loaded in or on the sensitive LB films. It is thought that we can obtain more accurate response mechanism of organic vapour using the resonant frequency and resonant resistance diagram. The polymeric sensitive material were quantitively depositied using the LB method. In the experimental results, the adsorption behavior of organic vapour response can be decided by two type ; surface adsorption and penetration into sensitive material. Organic vapours had different positions in the Frequency-Resistance (F-R) diagram as to the kinds and concentrations of organic vapours. Thus F-R diagram can be applied to the development of one channel gas sensing system using the Quartz Crystal Analyzer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.447-450
• /
• 2002

Recently polymeric insulators and arresters are being used for outdoor high voltage applications. Polymeric insulators for transmission line have significant advantages over porcelain and glass insulators, especially for ultra-high voltage(UHV) transmission lines. Their advantages are light weight, vandalism resistance and hydrophobicity. Polymeric insulator kind are a relatively new technology, but their expected life is still unknown. In this paper, the material property for polymeric insulating material such as silicone rubber and EPBM is investigated by cross-link time and the relation between tracking resistance and W resistance is analyzed by IEC 60587 and W aging experiment.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.119-120
• /
• 2016

This study is about development of inorganic insulation material using by-product materials. The organic material is due to toxic gas emission, when a fire occurs. And it has lower water resistance. The inorganic material is heavy and worse thermal performance than organic materials. In this study, installed light weight ceramic insulation by concrete structure to evaluation fire resistance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.865-868
• /
• 2000

It was examined that the relationship between microstructures, electrical properties and crystal structure of (1-x)CaMnO$_3$-xCaTiO$_3$solid solution system which was made by mixing a semiconducting material CaMnO$_3$of low resistance and a dielectric material CaTiO$_3$of high resistance with variable ratios (x=0, 0.1, 0.3, 0.5, 0.7, 0.9, 1.0). As the CaTiO$_3$increased, the resistance, B constant and lattice constant were increased, but the grain size was decreased. On particular, above 50wt% of CaTiO$_3$, the resistance at 2 5$^{\circ}C$ was rapidly increased due to the correlation in connectivity of the lattices between the conductive Mn$^{+4}$ octahedron and the insulative Ti$^{+4}$ octahedron.ron.

• 한국안전학회지
• /
• 제23권4호
• /
• pp.25-29
• /
• 2008

Recently, new functionally graded material(FGM) that has a spatial variation in composition and properties is developed because of its good quality. This material yields the demands for resistance to corrosion and high temperature in turbine blade, wear resistance as in gears and high strength machine parts. Especially coating treatment in FGM surface brings forth a mechanical weak at the interface due to discontinuous stress resulting from a steep material change. It often, leads cracks or spallation in a coating area around an interface. The behavior of propagation cracks in FGMs was here investigated. The interface stresses were reduced because of graded material properties. Also graded material parameter with exponential equation was founded to influence the stress intensity factor. And the resistance curve with FGM coating was slightly increased.

• 한국전기전자재료학회논문지
• /
• 제31권2호
• /
• pp.98-101
• /
• 2018

In this paper, we discuss the fabrication of metal alloy resistors. We connected them in parallel to estimate their resistance and temperature coefficient of resistance (TCR). The fabricated resistors have different resistances, 5 and $10{\Omega}$ and different TCRs, 50 and $200ppm/^{\circ}C$. Each resistor was confirmed to have the correct atomic composition through the use of energy dispersive X-ray (EDX). The resistors' electrical properties were confirmed by measuring resistance and TCR. The resistance and TCR of the resistors connected in parallel were estimated through the increase in resistance due to the increase in temperature, and were compared with the measured values. We are confident that this TCR estimation technique, which uses the increase in resistance due to temperature, will be very useful in designing and fabricating resistors with low and stable TCR.

• International Journal of Safety
• /
• 제4권2호
• /
• pp.6-11
• /
• 2005

The goals of the paper are to understand the impact damage behavior and identify the effect of surface protective materials on impact resistance in filament wound composite pressure vessels. For these, a series of low velocity impact tests was performed on specimens cutting from the full scale pressure vessel by the instrumented impact testing machine. The specimens are classified into two types, which are with and without surface protective material. The visualization for impact damage by two different impactors is made by metallurgical microscope. Based on the impact force history and damage, the impact resistance parameters were employed,rod its validity in identifying the damage resistance of filament wound composite pressure vessel was reviewed. As the results, the impact resistance of the filament wound composites and its dependency on the surface protective material were evaluated quantitatively

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.110-111
• /
• 2006

In this paper, we investigated resistance characteristic of chalcogenide material for next generation ReRAM nonvolatile memory device with laser irradiation. A AES is used to test Ag doping ratio into a As-Ge-Se-S thin film. A sample resistance was observed in real time with He-Ne laser(632.8nm). As a result, resistance of thermal treated As-Ge-Se-S thin film was $500{\Omega}$ which is smaller than initial $1.3M{\Omega}$. A resistance of non-treated Ag/As-Ge-Se-S thin film was $200{\Omega}$ which is lower than $35M{\Omega}$.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.1-6
• /
• 1998

An experimental study was performed to discover the tribological behaviors of pure tin and zinc coated 52100 bearing steel. Pure tin coatings ranging from 30 nm to 30,000 nm and pure zinc coatings ranging from 500 nm to 52,000 nm were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the effect of coating thickness on the tribological rolling behavior. Results showed that the existence of optimum film thickness which revealed minimum rolling resistance was discovered for tin and zinc coating. The compatibility of coating material to iron showed no significant effect on the rolling resistance behavior. The hardness of coating material revealed significant influence to the rolling resistance behavior.