• Transactions on Electrical and Electronic Materials
• /
• 제13권1호
• /
• pp.31-34
• /
• 2012

The addition of nano/micro silica into unsaturated polyester resin (UPR) results in the improvement of the electrical properties of Silica-UPR composites. The surface, volume resistivity, dielectric strength, dissipation factor and dry arc resistivity of nano silica-UPR composites were found to improve significantly. The effects of the nano and micro fillers in UPR have been evaluated. They are presented in this paper. To evaluate the electrical properties of the nano & micro composites, all the measurements were done as per the prescribed methods in ASTM. It was observed that the addition of nano silica improves the electrical properties as compared to micro silica. The better dispersion of silica particles in unsaturated polyester resin enhances the electrical properties of silica-UPR composites.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 터널.암반역학위원회 박사학위 논문집
• /
• pp.153-204
• /
• 1998

Prediction of lining loads due to tunnelling is one of the major issues to be addressed in the design of a tunnel. The objective of this study is to investigate rational and realistic design loads on tunnel linings. factors influencing the lining load are summarized and discussed. The instruments for measuring the lining loads are reviewed and discussed because field measurements are often necessary to verify the design methods. Tunnel construction in the City of Edmonton has been very active for storm and sanitary purposes. Since the early 1970's, the city has also been developing an underground Light Rail Transit system. The load measurements obtained from these tunnels are compared with the results from the existing design methods. However, none of the existing methods are totally satisfactory, Therefore, there is some room for improvement in the prediction of lining loads. The convergence-confinement method is reviewed and applied to a case history of a tunnel in Edmonton. The convergence curves are obtained from 2-D finite element analyses using three different material models and theoretical equations. The limitation of the convergence-confinement method is discussed by comparing these curves with the field measurements. Three-dimensional finite element analyses are performed to gain a better understanding of stress and displacement behaviour near the tunnel face. An improved design method is proposed based on the review of existing design methods and the performance of numerical analyses. A specific method or combination of two different methods is suggested for the estimation of lining loads for different conditions of tunnelling. A method to determine the stress reduction factor is described. Typical values of dimensionless load factors nD/H for tunnels in Edmonton are obtained from parametric analyses. Finally, the loads calculated using the proposed method are compared with field measurements collected from various tunnels in terms of soil types and construction methods to verify the method. The proposed method gives a reasonable approximation of the lining loads. The proposed method is recommended as an approximate guideline for the design of tunnels, but the results should be confirmed by field measurements due to the uncertainties of the ground and lining properties and the construction procedures, This is the reason that in-situ monitoring should be an integral part of the design procedure.

• 한국전기전자재료학회논문지
• /
• 제18권9호
• /
• pp.870-875
• /
• 2005

We measured the optogalvanic signal and discharge voltage-current(V-I) curve under the two different discharge conditions with different buffer gases, Ar, and Ne. When the Gd was used as a cathode material at low discharge current less than 10mA, a significant change was observed in the current-voltage curve. Time resolved optogalvanic signal measurement were measured by the diode laser of which wavelengths correspond to metastable transition line of these gases (Ar, Ne). From these measurements, we found that the characteristics of the V-I curve strongly depend on the Penning ionization process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.245-248
• /
• 1997

The distilled water is used for the ultrasonic wave propagating material in the measurements of broadband ultrasonic attenuation (BUA) that is applied in industrial and medical applications, The acoustic impedance of water is significantly changed with its temperature. Therefore, the quantitative evaluation of BUA with temperature and the ultrasonic wave propagating distance is highly needed. In this study, we evaluated the variation of attenuation with change in temperature. To measure the variation of BUA in the low frequency region at the temperatures, 27$^{\circ}C$, 29$^{\circ}C$, and 31$^{\circ}C$, we tested the Plyethylene, Teflon, MC-Nylon, Urethane specimens and analyzed the center frequency, frequency bandwidth, spectral peak amplitude. The results showed that BUA value appeared to be lower with increasing temperature. This may be due to the fact that the frequency feature of ultrasonic wave is affected by not only the specific gravity, acoustic impedence, but material crystalline, porosity, the distance of ultrasonic wave propagation in water.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2004년도 High Temperature Superconductivity Vol.XIV
• /
• pp.8-8
• /
• 2004

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.68-72
• /
• 2000

In order to estimate spatial charging process in the corona charging which has been used to make polymer electret, the electrical properties of polypropylene film were obtained from Thermally Stimulated Current (TSC) measurements after corona charging between knife electrode and cylinder electrode with the voltages of -5, -6, -7 and -8[kV], respectively. And then the electrostatic contour and the electric field vector were also simulated by using Finite Element Method (FEM). The edge effect around edge of knife electrode affected the electrostatic contour on surface of specimen and the electric field concentration inside specimen. The uneven charging state in the electret due to the mistake on design could be calculated and so the optimal design of corona charging device which is appropriate to various materials is come to be practicable.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1992년도 정기총회 및 추계학술발표회
• /
• pp.2-29
• /
• 1992

According to the increase of occupation density of microwave frequency band on use microwave environments have been congested extensively. For shielding unnecessary electromagnetic wave of preventing the electromagnetic wave reflection a good conductor a low resistive material or a lossy material is mainly used. As a method to measure the absorbing characteristics of microwave absorber the fundamental microwave measuring method can be used. There is however a big problem in measuring errors since the wavelength of microwave is very short especially as in the case as microwave absorber for RADAR. Therefore this research aimed to a converting adaptor of 20mm${\Phi}$ coaxial tube from a Type-N connector to 20mm${\Phi}$ coaxial tube and to use it for designing microwave absorber and evaluating absorbing characteristics. Furthermore the measurements of absorbing characteristics and material constants have performed and reviewed which were carried out by using the coaxial tube in the short type and by using rectangular waveguide respectively As a result the validity of the measured values have been confirmed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1222-1227
• /
• 2002

Noise barrier is used to reduce traffic noise. The effect of a noise barrier depends not only on the materials, but also on the physical properties such as density, height and degree of absorption, etc. Typical absorptive noise barrier is used sound absorbing material, such as glass wool and mineral wool. The goal of this study is to develope excellent absorptive noise barrier using a polyester. Laboratory measurements were peformed with various thicknesses, density and layer of absorber in a reverberation room.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 가을 학술발표회 논문집
• /
• pp.153-159
• /
• 1999

A material handling crane is composed of many complex structural components which require sufficient strength, stiffness and stability throughout its service life and need to be light in weight, and satisfy the required functions under the entire range of operating conditions. In this study, the analysis system for material handling cranes is presented. This program integrate various structural analyses modules with the GU(Graphic User Interface) concept. Utilizing basic variables as input data, the analysis system performs quasi-static, eigenvalue, buckling, fatigue and stability analysis. Using this program, the designer can generate optimal design data for the cranes without my actual measurements. This system will also be extended to other mechanical structures with kinematic motion like crane.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 1999

The electrical characteristics of fatty acid LB films were investigated to develop the gas sensor using Langmuir-Blodgett(LB) films which have high ordered orientation and ordering structure. The deposition status of fatty acid LB films were verified by the measurements of UV absorbance. The conductivity of fatty acid LB films for horizontal direction at room temperature was about $10^8[S/cm]$,/TEX>, which was correspond to semiconductor material. The activation energy for fatty acid LB films with respect to variation of temperature was about l.O[eV]. The response characteristics for organic gas were confirmed by measuring the response time, recovery time, and reproducibility of the fatty acid LB films to each organic gas. Also, the penetration and adsorption behavior of gas molecule were confirmed through the organic gas response characteristics of fatty acid LB films with respect to temperature.