• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.126-127
• /
• 2007

Sn-filled and Fe-doped $CoSb_3$ skutterudites were synthesized by encapsulated induction melting. Single ${\delta}$-phase was successfully obtained by subsequent annealing and confirmed by X-ray diffraction analysis. Temperature dependences of Seebeck coefficient, electrical resistivity and thermal conductivity were examined from 300 K to 700 K. The positive Seebeck coefficient confirmed the p-type conduction. Electrical resistivity increased with increasing temperature, which shows that the $Sn_zCo_3FeSb_{12}$ skutterudite is highly degenerate. Thermal conductivity was reduced by Sn-filling because the filler atoms acted as phonon scattering centers in the skutterudite lattice. Thermoelectric figure of merit was enhanced by Sn filling and its optimum filling content was considered to be z=0.3 in the $Sn_zCo_3FeSb_{12}$ system.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.5
• /
• pp.215-220
• /
• 2008

The kerfs between arrayed piezoelectric elements in a medical ultrasonic transducer or a piezoelectric composite transducer are generally filled by polymeric materials. The boundary condition of the elements for lateral mode vibration is changed according to the kerf-filling materials, so that the resonance frequency for longitudinal mode of the transducer is also varied. In this study, to investigate the resonance frequency variation for an arrayed transducer experimentally, the piezoelectric vibration elements of $14mm{\times}0.22mm{\times}0.44mm$ were fabricated and those were linearly arrayed. And, the resonance frequencies were measured for three cases of kerf-filling condition, non-filling and two different kinds of epoxy filling. Conclusively, it is confirmed that the resonant frequency variation shows the similar tendency with the theoretical one for the longitudinal mode.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.419-426
• /
• 2010

This paper discusses a series of experiments including material improvement in order to ensure quality of grouting for the post-tensioned structure. In presstressed concrete, grouting refers to the construction procedure of filling empty space of duct enclosing the prestress tendons using cementitious material, To date, adequate quality control of the grouting has not been established in Korea because the relationship between the grouting and durability of post-tensioned structure is not well-recognized. The Korean standard does not consider the important material characteristic, wick effect, which is caused by tendons in the ducts, and furthermore current standard testing method does not quantify reasonable material segregation. As a result, the grout material, which satisfies the current material standards, may well exhibit excessive bleeding of water or shrinkage during construction. In this study, international codes and standards related to grouting were surveyed. The mix proportions of the constituents and novel admixtures were suggested to meet equivalently with these standards. Performance of this enhanced grout was compared with common domestic grouts using the international standard testing method. A series of mock-up specimens considering geometry of PC beam was constructed and grout flow pattern was observed as the grout was injected. It was observed that the grouting performance was highly influenced by material properties and filling characteristic can be varied depending on geometry of ducts.

• 보존과학연구
• /
• s.29
• /
• pp.255-278
• /
• 2008

Considering the physical quality of the wall body in this study we tried to select a replenishing that is proper for filling the cracked part of the painting wall layer and apply the natural adhesives that have traditionally been used, investigating whether it is possible to substitute those for the chemical adhesive which is used at present time. The result of this study showed the red algae adhesive was, in a weathering environment, as safe as the synthetic resin originated from the polyvinyl acetate which is used generally on the present spot, and it was concluded that although the starch adhesive displayed its superiority in enhancing the strength of the earth mortar and its work disposition, it seemed proper for it to be used as a filling adhesive for the first or midterm layer because it showed a surface hardening phenomenon. And also the glue and fish glue were judged they were not qualified as a filling adhesive due to mold occurring in a environment of high moisture that is a biological problem, showing at same time a weak physical feature in a weathering environment. Therefore it would be possible to use the red algae adhesive or starch one substituting them for the original one sold on the present market, if among natural adhesives the weak points of the them were to be corrected.

• Restorative Dentistry and Endodontics
• /
• v.14 no.1
• /
• pp.97-105
• /
• 1989

This study was conducted to evaluate and compare the apical leakage among the retrograde filling materials; retrograde filling with non-zinc amalgam, cavity varnish and non-zinc amalgam, z.o.e cement, Glass Ionomer cement, scotch bond and silux. Sixty single rooted teeth were divided into six groups and each tooth was individually prepared for its particular group. The specimens were incubated at $37^{\circ}C$ for 24 hrs and then were infiltrated by 2% methylene blue for 7 days. Apical leakage was evaluated by measuring the degree of dye penetration between the filling material and the canal wall. The results were as follows: 1. The scotch bond and silux group showed the least amount of apical leakage and the control group showed the greatest amount of apical leakage. 2. The groups retrofilled with cavity varnish and amalgam, glass-Ionomer cement, scotch bond and silux showed significantly good apical seal than control group. 3. The groups retrofilled with glass Ionomer cement, scotchbond and silux showed significantly good apical seal than the groups retrofilled with Amalgam and Zinc oxide eugenol cement.

• Restorative Dentistry and Endodontics
• /
• v.11 no.1
• /
• pp.53-61
• /
• 1985

This study was conducted to evaluate and compare the apical leakage in the following retrograde techniques; apicoectomys, retrograde filling with zinc oxide eugenol cement, non-zinc and zinc amalgam, and cold-burnished gutta-percha method. One hundred twenty five upper anterior and lower premolar teeth were divided into five above mentioned groups and each tooth was individually prepared for its particular group. The specimens were incubated at $37^{\circ}C$ for 14 days and then were infiltrated by 2% methylene blue for 24 hours. The apical leakage was evaluated by measuring the degree of dye penetration between the filling material and the canal wall. The results were as follows: 1. The cold-burnished gutta-percha group showed the least amount of apical leakage and the apicoectomy group showed the greastest amount of apical leakage. 2. Statistics showed that there were significant differences among the groups (P<0.05), however there was no difference between the zinc oxide eugenol cement retrograde filling group and the non-zinc amalgam retrograde filling group (P>0.05).

• The Korean Journal of Rheology
• /
• v.11 no.2
• /
• pp.159-167
• /
• 1999

Sandwich injection molding is one of the remarkable polymer processes recently developed from conventional injection molding. But it is almost impossible to do theoretical investigation that we've researched it through numerical simulation. In this paper, numerical simulation on the study of sandwich injection molding is based on Finite Element Method and FAN/Control Volume method. In addition to conventional filling parameter that can confirm skin polymer melt front, new filling parameters have been introduced to confirm core polymer melt front advancement. These filling parameters are defined in each layer which is divided to solve temperature field along the thickness direction. One can notice different filling patterns resulted from the variation of material properties such as viscosities and power-law indexes, and processing conditions such as switch-over times and wall temperatures. It gives us a better understanding of the sandwich injection molding process. And we can recognize that it's the core polymer spatial distribution after the completion of filling that is the most important key point to use this process for industrial molding process.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.3
• /
• pp.37-42
• /
• 2012

The cement paste is mostly used as the filling materials of bored pile in Korea. The use of filling material based on cement paste is inefficient at field construction because it needs a lot of the charging mass. In addition, it has environmental problem according to the large amount of cement use because its strength is also larger than criterion. The excavated soil with stabilizer can be used as the filling materials when the bored pile is constructed. Therefore, this paper describes field application of solidified soil for economical efficiency and environment-friendly. The injection capacity of solidified soil is compared with cement paste's based on unconfined compressive strength test and field load test, and the appropriate of test results is evaluated by design criterion. The evaluation result shows that the capacity of excavated soil with stabilizer is similar to cement paste and the solidified soil is able to apply as filling materials of bored pile because it is satisfied with design criterion.

• Restorative Dentistry and Endodontics
• /
• v.13 no.1
• /
• pp.53-67
• /
• 1988

An investigation was carried out to compare the pulp responses against a few type of composite and streptococcus mutans contamination under the zinc oxide eugenol cement, and also confirmed pulpal responses of various composites with or without base. Seventy eight teeth from 6 dogs were employed and divided into 6 groups. Class V cavities were prepared on each tooth routinely with low speed dental engine. Paper disc about 0.3mm thick was immersed in the BHI broth in which streptococcus mutans had been enriched and the disc was inserted on the cavity floor prior to filling. Scotch bond puls Silux as Bis-GMA system composite resin and Helimolar as urethane system composite resin were adopted. Control group: Zinc-Oxide Eugenol cement filling Experimental groups: Group 1. Scotch bond + Silux filling with Dycal base Group 2. Heliomolar filling with Dycal base Group 3. Scotch bond + Silux filling without base Group 4. Heliomolar filling without base Group 5. Streptococcus mutans application. All cavities were sealed with thick ZOE cement to avoid marginal leakage. Postoperative intervals of 1, 2, 3, 4, 5 and 6 weeks teeth were carefully extracted, processed and stained with Hematoxylin and Eosin. The results were as follows: 1. S. mutans application group and composites without any base showed more severe pupal response than control group and dyca based groups. 2. The experimental group of S. mutans application showed severe response in the early stage compared to the two groups of composite resin without base, but no significant difference was found following periods. 3. The difference of pulpal response is not significant between Bis-GMA system and urethane system. 4. Streptococcus mutans application group and composites without base groups showed the evidence of histologic recovery at the six week cases and the large amount of reparative dentin was the prominent feature. 5. Pulp responses against every material were inclined to normal according to the time elapsed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.174-178
• /
• 2001

In order to reduce the lead-time and cost, recently the technology of rapid protoyping and manufacturing(RPM)has been widely used. Machining process is still considered as one of the effective RPM methods that have been developed and currently available in the industry. It also offers practical advantages such as precision and versatility. Some considerations are still required during the machining process. One of the most important points is fixturing. There should be an effective method of fixturing since the fixturing time depends on the complexity of geometry of the part to be machined. In this paper, the rapid manufacturing process has been developed combining machining with automatic filling. The proposed fixturing technique using automatic filling can be widely applicable to free surface type of product such as a fan. In the filling stage, remeltable material is chosen for the filling process. An automatic set-up device attachable to the table of the machine has also been developed. The device ensures the quality during a series of machining operations. This proposed process has shown to be a useful method to manufacture the required products with the reduced the response-time and cost.