• Korean Journal of Food Science and Technology
• /
• v.22 no.5
• /
• pp.497-502
• /
• 1990

The effect of sugar concentration, immersion time and temperature on water loss, solid gain or loss, and sugar molality of potatoes during osmotic concentration was analyzed by a response surface methodology (RSM), and those values were predicted by using a second degree polynomial regression model. Effect of osmotic concentration and blanching on vitamin C retention of air dried potatoes (6% MC: wet basis) was also evaluated. The most significant factor was sugar concentration for water loss, solid gain or loss, sugar molality, rate parameter and retention of vitamin C. Second and third factors were immersion time and temperature respectively. Water loss and solid gain were rapid in the first 10 min and then levelled off. A 44.6% of water loss was observed during osmotic concentration using a sugar solution $(60\;Brix,\;80^{\circ}C$) with 20 min of immersion time. Dried potatoes after osmotic concentration had higher vitamin C content than dried potatoes after blanching. Optimum regions for osmotic concentration process of potatoes were $60-70^{\circ}C$ of immersion temperature, 60 Brix of sugar solution and 16-20 min of immersion time based on above 30% of water loss and 50% of vitamin C retention.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.62-75
• /
• 1991

The purpose of this study is to perform modelings and experiments to measure air flow rate using hot-wires and a CTA(Constant Temperature Anemometer). The flow rate can be obtained by measuring the heat loss of the hot-wire due to the variations of flow velocity when the hot-wire is maintained at uniform temperature. But the defect of this method is that the output signal changes not only by the flow rate but also by the ambient temperature. Thus, in the present study, a method which compensates the variations of the ambient temperature has been introduced to measure exact flow rate. To be more specific, the bridge circuit of the usual hot-wire anemometer system has been modified in such a way that a temperature resistance sensor and a variable resistance are placed in one of the legs to compensate the different temperature coefficients of both the hot-wire and the temperature compensating resistance for flow velocity or for flow mass up to the flow temperature of 50 .deg.C. Comparing the modeling and experimental results, it has been shown that the compensating point differs as the flow rate varies. Therefore, optimum compensation points are sought to construct the circuit. The present modeling and experimental results may be applied to the design of actual air flow meters for automobiles.

• Fire Science and Engineering
• /
• v.28 no.3
• /
• pp.55-61
• /
• 2014

This study was performed to test the combustive properties of pinus rigida specimens treated with methylpiperazinomethyl-bis-phosphonic acid $M^{n+}$ ($PIPEABPM^{n+}$)s and methylpiperazinomethyl-bis-phosphonic acid (PIPEABP). Pinus rigida Plates were painted in three times with 15 wt% $PIPEABPM^{n+}s$ and PIPEABP solutions at the room temperature respectively. After drying specimen treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). It was indicated that the specimens treated with $PIPEABPM^{n+}s$ showed the lower speed to peak mass loss rate ($MLR_{peak}$), (0.104~0.121) g/s than that of PIPEABP plate. In adition, the specimens treated with $PIPEABPM^{n+}s$ showed both the lower total smoke release rate (TSRR), (224.4~484.0) $m^2/m^2$ and $CO_{mean}$ production (0.0537~0.0628) kg/kg than those of PIPEAB plate. Especially, for the specimens treated with $PIPEABPM^{n+}$ by reducing the smoke production rate except 2nd-smoke production rate (2nd-SPR), (0.0254~0.02270) g/s treated with $PIPEABPNi^{2+}$, 2nd-SPR (0.0117~0.0146) g/s was lower than that of PIPEABP plate. Thus, It is supposed that the combustion-retardation properties were improved by the partial due to the treated $PIPEABPM^{n+}s$ in the virgin plate.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.505-510
• /
• 2015

This study was performed to test the combustive properties of pinus rigida specimens treated with methylpiperazinomethyl-bis-phosphonic acid $M^{n+}$ ($PIPEABPM^{n+}$)s and methylpiperazinomethyl-bis-phosphonic acid (PIPEABP). Each pinus rigida plates were painted three times with 15 wt% $PIPEABPM^{n+}s$ or PIPEABP solutions at the room temperature. After drying specimens treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). It was indicated that the speed to peak mass loss rate ($MLR_{peak}$), (0.104~0.121) g/s for specimens treated with $PIPEABPM^{n+}s$ was lower than that of PIPEABP plate. In addition, the total smoke release rate (TSRR), $(224.4{\sim}484.0)m^2/m^2$ for $PIPEABPM^{n+}s$ treated specimens except specimen treated with PIPEABPAl3+ and $CO_{mean}$ production (0.0537~0.0628) kg/kg was smaller than that of PIPEABP plate. In particular, for the specimens treated with $PIPEABPM^{n+}$ by reducing the smoke production rate, the second-smoke production rate (2nd-SPR) $(0.0117{\sim}0.0146)m^2/s$ was lower than that of PIPEABP plate. It can thus be concluded that combustion-retardation properties of the treated $PIPEABPM^{n+}s$ were partially improved compared to those of the virgin plate.

• Fire Science and Engineering
• /
• v.27 no.6
• /
• pp.57-63
• /
• 2013

This study was performed to test the combustive properties of Pinus rigida specimens treated with piperazinomethyl-bis-phosphonic acid (PIPEABP), methylpiperazinomethyl-bis-phosphonic acid (MPIPEABP), and N,N-dimethylethylene-diaminomethyl-bis-phosphonic acid (MDEDAP). Pinus rigida Plates were painted in three times with 15 wt% alkylenedi-aminoalkyl-bis-phosphonic acid solutions at the room temperature. After drying specimen treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). It was indicated that the specimens treated with chemicals showed the later time to peak mass loss rate ($TMLR_{peak}$) = (315~420) s than that of virgin plate by reduc-ing the burning rate except for $TPMR_{peak}$ (280 s) treated with DMDAP. In adition, the specimens treated with chemicals showed both the higher total smoke release rate (TSRR) (407.3~902.0) $m^2/m^2$ and $CO_{mean}$ production (407.3~902.0) $m^2/m^2$ than those of virgin plate. Especially, for the specimens treated with PIPEABP, 1st-smoke production rate (1st-SPR) (0.1250~0.1297) g/s was lower than that of virgin plate, while the 2nd-SPR (0.183 g/s) was higher. Thus, It is supposed that the combustion-retardation properties were improved by the partial due to the treated alkylenediaminoalkyl-bis-phos-phonic acids in the virgin Pinus rigida.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.6
• /
• pp.689-699
• /
• 2003

This study was to examine characteristics of treating toluene vapor, which gets to be problematic due to its harmful carcinogenicity and mass generation from various sources, through a biological treatment facility which is environment-friendly and adopts a high-efficient and low-cost clean technology. In order to identify whether Alnus Firma Fruit (AFF) can be used as a media for a bioreactor, its utility and basic operating factors, a study was conducted on pressure drop, supply of nutrient substances and retention time which are operating factors of a biofilter, and eliminating characteristics were compared between AFF and the conventional biological activatedcarbon (BAC) widely used as filter media. In the case of AFF, the initial microbial deposits was 2.3${\times}$10$^{7}$ CFU/g dry AFF, which represents the initial microbial density higher than the case of BAC showing 5.5${\times}$10$^{6}$ CFU/g dry BAC And it took about 2 weeks to acclimate until its eliminating rate got to be increased over 90%. As a result of comparing pressure loss taking place with the lapse of time between BAC and AFF, after 130 days passed at SV 25h$^{-1}$ , BAC showed that its eliminating efficiency had a tendency to drop greatly due to a great pressure loss (0.53\longrightarrow54.7 mm$H_2O$/m) caused by an excess of biomass as accumulated. On the other hand. AFF showed that the pressure drop was 0.53 mm$H_2O$/m, about 2 times as much as the initial pressure loss of 0.4 mm$H_2O$/m, which represents no great change in the pressure loss, and its eliminating efficiency was also shown to be continuously high. Therefore, when AFF was used as a filler for a biological treatment facility, a biological filter enabling improvement of the purifying efficiency to be promoted could be provided, and moreover, the pressure loss was so small that the filler replacement cycle or the back flushing cycle could be extended. So, even in terms of the operating cost, it was identified to be an economical filler When an inorganic material was used as a filler, the biofilters performance acted sensitively on whether nutrient substances were supplied or not. In the case of AFF with low adsorptivity, addition of ethyl-alcohol increased the solubility of toluene, and consequently, biodegradation got to be actively made by microbes, and thus, its eliminating rate could be increased. As the flow velocity and the inflow concentration got to be more increased, its eliminating rate got to be lower, and particularly, an increase in the flow velocity made its eliminating rate drop more greatly than an increase in the concentration.

• Korean Journal of Environment and Ecology
• /
• v.24 no.3
• /
• pp.279-285
• /
• 2010

This study was conducted to evaluate the differences between the heavy metal contaminated and non-contaminated Artemisia princeps var. orientalis and Equisetum arvense in litter decomposition processes. The plant samples were collected from abandoned mine tailings and control sites in Cheongyang, South Korea. The abandoned mine tailings have high heavy metal concentration and low soil organic matter contents. The heavy metal contents of mine tailings were about 13 and 28 times higher in As and Cd, compared to those in control soils. Also, the contents of the Cr, Ni and Zn in mine tailings were about 3 to 6 times higher than those in control soil. Samples of two plant species from mine tailings have high heavy metal concentrations compared to those from control sites. The leaf of A. princeps var. orientalis and shoot of E. arvense collected from mine tailings have approximately 23 and 58 times more in As, and 25 and 11 times more in Cd. The mass loss rates of plant litter from mine tailings were slower than those from control sites. During the experimental period, the decomposition of A. princeps var. orientalis leaf from mine tailings and control site showed 50.4% and 65.7% mass loss on the control soil area, respectively. The decomposition of A princeps var. orientalis leaf from mine tailings and control site showed 31.6% and 57.5% mass loss on the mine tailings area, respectively. The decomposition of A. princeps var. orientalis stem from mine tailings and control site showed similar patterns with their leaf decomposition. The decomposition of E. arvense shoot from mine tailings and control site showed 77.8% and 89.3% mass loss on the control soil area, respectively. The decomposition of E. arvense shoot from mine tailings and control site showed 67.6% and 82.1% mass loss on the mine tailings area, respectively. Therefor, the higher contents of heavy metals showed slow decomposition. The results suggested that heavy metal contamination affected the plant litter decomposition processes.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.478-485
• /
• 2015

The aim of this study is to analyze the combustion and thermal properties in order to establish baseline data for the fire safety evaluation of domestic timbers. The combustion properties such as heat release rate, total heat release, gas yield, and mass loss were analyzed by the method of cone calorimeter test and thermogravimetry (TGA). Thermal decomposition temperatures of the specimens by TGA were recorded as $359.83^{\circ}C$ for White pine, $359.80^{\circ}C$ for Red-Leaved Hornbeam, $363.14^{\circ}C$ for Carolina poplar, $358.59^{\circ}C$ for Konara oak, and $362.11^{\circ}C$ Sargent cherry. Red-Leaved Hornbeam showed the highest value of heat release rate, but, Carolina poplar wood showed the lowest value. In case of the total heat release, Red-Leaved Hornbeam wood showed the highest value and Carolina poplar wood showed the lowest one. The gas analysis results showed that Sargent cherry wood had the lowest value of 0.021, and Konara oak had the highest at 0.031 in the $CO/CO_2$. The minimum value of mass reduction was recorded as 87.57% for Sargent cherry, but, on the other hand, it was 95.03% for Konara oak. There was a correlation between the gas generation of CO and $CO_2$, and combustion behavior of woods. These results are expected to be usful for providing a fundamental guideline with the fire safety of wood use in interior applications.

• Fibers and Polymers
• /
• v.6 no.1
• /
• pp.35-41
• /
• 2005

Research and development of nano fiber products is very active over the world. Physical characteristics and dyeing properties of nylon 66 nano fiber were investigated in this study. X-ray diffraction, DSC, analysis of amino end group, and water absorption were performed to get information concerning physical properties of nano fiber. Nylon 66 nano fiber was dyed with high molecular mass acid dyes. Effects of dyeing temperature, pH of dyeing solution, and concentration of acid dyes on dyeing properties such as rate of dyeing and the extent of exhaustion, were examined and compared to those of regu­lar fiber. It was found that nano fiber adsorbed acid dyes at lower temperature, got rapidly dyed, and its extents of exhaustion at specific dyeing temperature were higher than regular fiber. It was also observed that nano fiber could adsorb a large amount of acid dye without a significant loss in the extent of exhaustion. Washing fastness of the dyed nano fiber was lower by $1/2\~1$ grade, light fastness by 1 grade than the dyed regular fiber.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.4
• /
• pp.220-228
• /
• 2002

The cool-down performance after soaking is very important in an automotive air-conditioning system and is considered as a key design variable. Therefore, transient characteristics of each system component are essential to the preliminary design as well as steady-state performance. The objective of this study is to develop a computer simulation model and ostinato theoretically the transient performance of an automotive air-conditioning system. To do that, the mathematical modelling of each component, such as compressor, condenser, receiver/drier, expansion valve, and evaporator, is presented first of all. The basic balance equations about mass and energy are used in modelling. For detailed calculation, condenser and evaporator are divided into many sub-sections. Each sub-section is an elemental volume for modelling. In models of expansion valve and compressor, dynamic behaviors are not considered in this analysis, but the quasisteady state ones are just considered, such as the relation between mass flow rate and pressure drop in expansion device, polytropic process in compressor, etc. Also it is assumed that there are no heat loss and no pressure drop in discharge, liquid, and suction lines. The developed simulation model is validated by comparing with the laboratory test data of an automotive air-conditioning system. The overall time-tracing properties of each component agreed well with those of test data in this case.