• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권2호
• /
• pp.137-141
• /
• 2005

A transverse flux, PM-exited linear motor (TFM-LM) with inner mover was designed and built. Its output power density is higher and its weight is lower than those of the conventional PM exited linear synchronous motors (PM LSM). To obtain the maximum thrust force under the given volume, the thrust force density with respect to the ratio of the slot width and the length of pole pitch is analyzed by the 3-dimension finite element method (FEM). Finally, calculated static thrust forces was compared with the experimental values. The calculated and measured performance of the transverse flux, PM-exited linear motor with inner mover revealed great potential for system improvements by reducing the mass of the linear motor. For examples, when this motor was applied to a ropeless elevator, it was possible to increase the power density by more than 400% over the conventional PM-LSM. The results of this study recommend this type of motor for the ropeless elevator or gearless direct linear driving system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.526-531
• /
• 2003

A cone cylinder is used to obtain variable operation conditions of a sonic ejector-diffuser system. The cone cylinder is movable to change the ejector area ratio, thus obtaining variable mass flow rates. The present study investigates the effects of ejector throat area ratio and operating pressure ratio on the entrainment of secondary stream. The numerical simulations are based on a fully implicit finite volume scheme of the compressible, Reynolds-Averaged, Navier-Stokes equations. The ejector throat area is varied between 3.94 and 8.05, and the operating pressure ratio is changed from 3.0 to 9.0. The results show that the entrainment ratio and mass flux ratio become more dependent on the ejector throat area ratio, when the pressure operating ratio is low. The total pressure losses produced in the present ejector system increase with the operating pressure ratio and the ejector area ratio, but for a given operating pressure ratio, the losses are not significantly dependent on the ejector area ratio when it is larger than about 5.0.

• 설비공학논문집
• /
• 제14권10호
• /
• pp.825-832
• /
• 2002

The present study investigated the enhancement of the absorption performance by the spring wrapped around the outer surface of the vertical falling film absorber tube. Heat and mass transfer enhancements were experimentally investigated, and flow visualization was performed to observe the wettability and flow pattern of the solution. The key experimental parameters were spring diameter (0.5, 1.0 mm) and spring pitch (1, 3, 10 mm), film Reynolds number (50~150), and concentration of LiBr-$H_2O$ solution (55, 60, 65 wt%). As the spring diameter was increased, the absorption mass flux, Sherwood number, Nusselt number, heat flux, and heat transfer coefficient were increased The Nusselt and Sherwood numbers showed the maximum at the spring pitch of 3mm, and the ratio of pitch to diameter of approximately 3 and 6 for the spring diamter of 0.5 mm, respectively.

• 설비공학논문집
• /
• 제18권8호
• /
• pp.627-634
• /
• 2006

Evaporation heat transfer characteristics by pulsating flow in a plate heat exchanger have been investigated experimentally in this study. R-l34a is evaporated by receiving heat from the hot water in the plate heat exchanger. The pulsating frequency in refrigerant side of the plate heat exchanger is varied in the range of 5-25 Hz. The operating pressure of R-l34a and mass flux of hot water are also varied 0.6-0.9 MPa and $45-105 kg/m^2s$, respectively. The experimental results indicate that evaporation heat transfer coefficient of pulsating flow is improved up to 6.3% compared with that of the steady flow at 10 Hz and $G_w=45 kg/m^2s$. It is also found that the evaporation heat transfer enhancement ratio is decreased with an increase in mass flux of hot water, and the evaporation heat transfer enhancement is little influenced by operating pressure of R-l34a.

• 설비공학논문집
• /
• 제18권1호
• /
• pp.31-37
• /
• 2006

The present study has been experimentally investigated the effect of geometric and operating parameters on the two-phase flow distribution of refrigerants in a horizontal T-junction. The operating parameters were the kind of refrigerants (R-22, R- l34a, and R-410A), saturated temperature, and the inlet mass flux and quality. The geometric parameters were the tube diameter and the tube diameter ratio. The measured data of refrigerants were compared with the values predicted using the models developed by several researchers for air/water or steani/water two-phase flow. Among the operating parameters, the inlet Quality was the most sensitive to the mass flow rate ratio. Between the geometric parameters, the tube diameter ratio was more sensitive than tube diameter.

• 에너지공학
• /
• 제8권2호
• /
• pp.298-308
• /
• 1999

과냉각수조로 분사되는 증기의 직접접촉 응축특성을 알아보기 위하여 다섯 개의 수평 노즐에 대해 증기 질량유량과 수조 온도를 여러 가지로 변화시키면서 실험적 연구를 수행하였다. 증기응축현상을 육안관찰과 고속 비디오 카메라를 사용한 방법으로 분석한 결과, 안정된 증기제트인 경우 증기 질량속과 수조온도가 변화함에 따라 타원형 및 원추형 증기제트 형상이 나타나는 것을 관찰하였다. 증기제트 팽창비, 증기제트 길이 및 응축연전달계수를 구하였고, 증기 질량속, 수조온도 및 노즐 내경이 미치는 영향을 분석하였다. 증기제트 길이와 응축열전달계수를 증기 질량속 및 응축추진 포텐셜의 함수로 나타낸 상관식을 구하였다. 증기제트 내부와 주위 수조온도 분포를 구했으며 증기 질량속, 수조온도 및 노즐 내경이 미치는 영향을 분석하였다. 처깅, 천이처깅, 응축진동, 안정응축, 방울응축진동 및 간헐진동응축 등 여섯 가지 영역으로 구분된 응축 영역도를 작성하였다. 그 외, 수조 벽면에서의 동압을 측정하였고, 증기 질량속과 수조온도에 따라 변화하는 증기 응축모드와 동압과는 밀접한 연관성이 있음을 확인하였다.

• 대한기계학회논문집B
• /
• 제26권3호
• /
• pp.448-457
• /
• 2002

Heat treatment such as quenching of a high-temperature cylinder is being used on steel to produce high strength levels. Especially, the mist cooling with the high and uniform surface heat flux rate s expected to contribute for better products. The experimental mist cooling curve is produced for better understanding, and two distinct heat transfer regions are recognized from the cooling curve produced. It is shown that the liquid film evaporation dominated region follows the film boiling-dominated region as decreasing the temperature of test cylinder by mist flow. Based on the intuitive view from some previous investigations, a simplified model with some assumptions is introduced to explain the mist cooling curve, and it is shown that the estimation agrees well with our experimental data. In the meanwhile, it is known that the wetting temperature, at which surface heat flux rate is a maximum, increases with mass flow rate ratio of water to air ($\varkappa$ < 10). However, based on our experimental data, it is explained that there exists a critical mass flow rate ratio, at which the wetting temperature is maximum, in the range of 3 < $\varkappa$ < 130. Also, it is described that despite of the same value of $\varkappa$, the wetting temperature may increase with mist velocity.

• 천문학회지
• /
• 제48권2호
• /
• pp.105-112
• /
• 2015

The symbiotic star V1016 Cygni, a detached binary system consisting of a hot white dwarf and a mass-losing Mira variable, shows very broad emission features at around 6825 Å and 7082 Å, which are Raman scattered O vi λλ 1032, 1038 by atomic hydrogen. In the high resolution spectrum of V1016 Cyg obtained with the Bohyunsan Optical Echelle Spectrograph these broad features exhibit double peak profiles with the red peak stronger than the blue counterpart. However, their profiles differ in such a way that the blue peak of the 7082 feature is relatively weaker than the 6825 counterpart when the two Raman features are normalized to exhibit an equal red peak strength in the Doppler factor space. Assuming that an accretion flow around the white dwarf is responsible for the double peak profiles, we attribute this disparity in the profiles to the local variation of the flux ratio of O vi λλ 1032, 1038 in the accretion flow. A Monte Carlo technique is adopted to provide emissivity maps showing the local emissivity of O vi λ1032 and O vi λ1038 in the vicinity of the white dwarf. We also present a map indicating the differing flux ratios of O vi λλ 1032 and 1038. Our result shows that the flux ratio reaches its maximum of 2 in the emission region responsible for the central trough of the Raman feature and that the flux ratio in the inner red emission region is almost 1. The blue emission region and the outer red emission region exhibit an intermediate ratio around 1.5. We conclude that the disparity in the profiles of the two Raman O vi features strongly implies accretion flow around the white dwarf, which is azimuthally asymmetric.

• 한국산학기술학회논문지
• /
• 제18권4호
• /
• pp.608-613
• /
• 2017

본 연구에서는 저품위인 35wt% 금합금에 대해 80.0wt% 이상의 Au를 얻기 위한 건식 정련 공정을 제안하였다. Au35wt%-Ag5wt%-Cu60wt%의 조성을 가진 금합금에 대해 PbO/(PbO+CaO)의 혼합비를 각각 0~1로 변화시키고 플럭스/금합금의 무게비는 1/2로 하여 $1200^{\circ}C$-5시간의 열처리를 진행하였다. 이때 공정 전, 후 시료의 조성 변화는 energy dispersive X-ray spectroscopy(EDS)로 확인하고, 공정이 완료된 후 분리된 플럭스 금속 원소 성분은 time of flight secondary ion mass spectromerty(ToF-SIMS)로 확인하였다. EDS분석 결과 플럭스의 비율이 1(PbO 단일)인 경우 Au의 함량이 35.0wt%에서 86.7wt%로 가장 크게 향상되었고, 다른 플럭스 조성의 경우도 84wt% 이상으로 정련이 가능하였다. 또한 2/3 혼합비의 플럭스에서 Ag가 플럭스부로 빠져나가는 손실이 가장 적었다. 플럭스부의 ToF-SIMS 분석 결과 플럭스의 비율이 1, 0 일 때 $Au^+$의 특성 피크의 강도가 각각 349, 37로 측정되었다. Au의 손실을 고려하였을 때 CaO 단일 플럭스의 사용이 더 유리할 수 있었으나, 이 정도의 신호강도는 무시할 수 있는 정도로 판단되었다. 따라서 혼합플럭스를 이용한 건식 열처리를 통해 효과적인 금의 정련이 가능하여 경제적인 습식제련의 전처리 공정으로 사용될 수 있음을 확인하였다.

• 대한기계학회논문집B
• /
• 제41권3호
• /
• pp.171-181
• /
• 2017

2상 횡 유동은 응축기, 증발기와 원자력의 증기 발생기와 같은 열교환기의 튜브와 셀 사이에 존재한다. 공기/물의 2상 유동에 놓인 관군에 작용하는 항력을 실험적으로 평가하였다. 2상 유동에 놓인 관군은 정사각형 배열이다. 피치 직경 비는 1.35이었고, 실린더의 직경은 18 mm이다. 관군에 유동방향으로 작용하는 항력을 측정하여 항력계수와 2상 유동 감쇠비를 계산하였다. 2상 유동 감쇠비는 균질 2상 유동의 이론식을 사용하여 구하여 실험의 결과와 비교하였다. 압력과 항력의 상관계수를 실험결과를 고려하여 평가하였다. 상관계수는 이론적으로 항력을 계산할 때에 사용된다. 질량유량을 증가할수록 측정된 항력으로부터 구한 항력계수와 감쇠비가 균질 유동의 이론적 결과와 잘 일치함을 보이고 있다. 결과적으로 충분히 큰 질량 유량의 기포 유동인 경우에는 감쇠비를 균질 유동에 근거한 이론식으로 계산할 수 있다.