• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.1
• /
• pp.40-49
• /
• 2017

In this study, we have made the annual total phosphorus (TP) mass balance diagrams for I wastewater treatment plant by utilizing the data of flow rate and TP of each process and tried to choose the optimum unit process empirically for phosphorus recovery. For the applicability evaluation, we have suggested several quantitative indices of flow rate, TP concentration, TP load and SS. Based on the analyses of TP mass balance, it became clear for reducing TP load of the wastewater treatment plant that it is efficient to recover phosphorus from the side stream in which the amount of flow rate is just 1/16, but TP concentration and load are 78 and 4.8 times larger than those of the influent of the plant. After the detailed applicability evaluation for the side stream, it could be concluded that the unit process of waste activated sludge thickener supernatant or dehydration filtrate are appropriate. Meanwhile, we did fundamental experiments utilizing the dewatering filtrate with TP concentration of 141.5 mg/L. After adjusting pH 10 and $Ca^{2+}$ concentration 250, 500, 1000 mg/L, it was stirred slowly. As a result, the $PO_4-P$ and TP removal efficiencies were above 95 percent; the results of the experiment imply the applicability of phosphorus recovery process in a wastewater treatment plant strongly.

• Journal of Korean Public Health Nursing
• /
• v.26 no.1
• /
• pp.147-157
• /
• 2012

Purpose: The purpose of this study was to identify the related factors of change affecting the stages of change for exercise, on the assumption that there are various stages of change in the exercise behavior of women in nursing college. Methods: The subjects were 496 female college students in D city. The research instruments were stages of change for exercise behavior, the process of change, decisional balance, and self-efficacy. The dates were analyzed by descriptive statistics, ANOVA, and stepwise multiple regression using the SPSS 18.0 program. Results: The distribution of the subjects across the stages was: pre-contemplation, 17.7%; contemplation, 58.7%; preparation, 19.0%; action, 2.8%; maintenance, 1.8%. Analysis of variance showed that cognitive process (F=17.26, p<0.01), behavioral process (F=27.05, p<0.01), the pros of decisional-balance (F=7.07, p<0.01), the cons of decision-balance (F=5.82, p<0.01), and self efficacy (F=17.79, p<0.01) were significantly associated with the change of exercise behavior stages. The related factors of change affecting the change of exercise behavior stage were the cons of decision-making, counter conditioning, self re-evaluation, and body mass index, including 28.4% R-square. Conclusion: The transtheoretical model would be applicable to explain the exercise behavior of some women in nursing college. So, this study will be useful information for developing effective exercise behavior programs considering female students' stages of change.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.57-62
• /
• 2023

As a representative method for mass production, a multi-cavity type mold capable of simultaneously molding products of the same shape can be applied. It has the advantage of improving the productivity from several times to several tens of times, but it may cause disadvantages which is the quality deviation with each cavity. This study, therefore, has tried to increase the cavity filling balance by using a melt flipper and a flow distance control part in the runner part of the mold. Along with this, the design and manufacturing of air vents during injection molding have been verified through experimental methods to achieve a higher level of multi-cavity filling balance and dimensional accuracy.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.8 no.11
• /
• pp.17-25
• /
• 1985

In these days the industrial management are characterized by mass production. Mass production which is not possible without the rationalization in the process of production and the efficient scale of management needs development of technical administration. The object of this study is set up on the rationalization in the process of production. And this rationalization is a means to the aim of industrial management. So as to realize the rationalization in the process of production, we should think on plan of production and the line of balancing in processes of work. The line of balancing is considered as one of very valuable administration methods. The line of balancing that controls capacities and loads so that processes of work might balance in each other makes away with happenings of idleness and stagnation during the process of work As a natural consequence it follows (1) shortening in the period of Production, (2) more efficient, (3) removing the lots of tine and matter, (4) more efficient using in elements for production. Therefore, through the labour productivity and the efficiency of the process of production increased by these effects, the line of balancing was intended to curtail the basic cost. Though the previously said line of balancing could be applied to production, it should not be said that we can completely balance in each lines of work. In other words it is impossible that the line of balancing is completely executed in every lines of work. For that reason, we should arrange the level of balancing in lines. Nowaday, in our country, it is true that the line of balancing is hardly executed at manufacturing industries. Therefore if we execute and apply the line of balancing to manufacturing industries and the larger field as well , we could curtail the basic cost, through which we could reinforce not only the international competative power but increase the labour productivity. As a result, by these effects, we would rationalize the industrial management.

• Journal of environmental and Sanitary engineering
• /
• v.12 no.2
• /
• pp.1-12
• /
• 1997

This research aims to develop biofilm process for the nutrient removal of piggery wastewater. The developed process is the four stage anoxic-oxic biofilm process with recirculation of the final effluent. In summery, the results are as follows: 1. Nitrification in the piggery wastewater built up nitrite because of the high strength ammonia nitrogen. The nitrification of nitrobacter by free ammonia was inhibited in the total ammonia nitrogen loading rate with more than 0.2 kgNH$_{3}$-N/m$^{3}$·d. 2. The maximal total ammonia nitrogen removal rate was obtained at 22$\circ $C and without being affected by the loading rate. But total oxidized nitrogen production rate was largely affected by loading rate. 3. Autooxidation by the organic limit was a cause of the phosphorus release in the aerobic biofilm process. But the phosphorus removal rate was 90 percent less than the influent phosphorus volumetric loading rate of above 0.1 kgP/m$^{3}$·d. Therefore, the phosphorus removal necessarily accompanied the influent loading rate. 4. On the anoxic-oxic BF process, the total average COD mass balance was approximately 67.6 percent. Under this condition, the COD mass removal showed that the cell synthesis and metabolism in aerobic reactor was 42.8 percent and that the denitrification in anoxic reactor was 10.7 percent, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.4
• /
• pp.7-12
• /
• 2012

Extrusion is one of the most important operations in the polymer-processing industry. Development of models for extrusion and computer tools offer a route to developing reliable and optimized process designs. The models are based on the analysis of physical phenomena encountered during the process. Balance equations for mass, momentum and energy are fundamental to the problem. A predictive computer model has been developed for the single screw extruders with conventional screws of different geometry. The model takes into account melting zones of the extruder and describes an operation of the extruder system, making it possible to predict mass flow rate of the polymer, pressure and velocity profiles along the extruder screw channel. The simulation parameters are the material and rheological properties of the polymer; the screw pitch, and screw speed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.189-194
• /
• 2012

The purpose of this study is to predict the performance of a cyclone drying machine and air ejector used in drying applications. This paper deals with optimization of the geometry of the ejector for sludge drying using computational fluid dynamics. To facilitate the design of a jet ejector for air drying machines, a numerical model of simultaneous mass and heat transfers between the liquid(sludge) and gas(air) phases in the jet ejector was developed. The steady-state model was based on unidimensional balance equations of mass, energy and momentum for the liquid and gas phases. It was shown that the optimum condition to minimize pressure and momentum loss of air in the ejector was d=220mm. It was found that sludge particles inside the cyclone was smoothly discharged by the conical wedge installed on the bottom of the cyclone.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.130.1-130.1
• /
• 2010

미국과 유럽에서는 이미 10여 년 전부터 250MW급 이상의 대용량 석탄IGCC 플랜트를 상업운전 하고 있으며, 일본과 중국을 비롯한 아시아에서도 대용량 플랜트를 시운전하고 있거나 건설 중에 있다. 한국에서는 제4차 전력수급계획에 의거 태안화력 부지 내에 300MW급 IGCC 플랜트 건설을 추진 중이며, 두산중공업은 '10년 상반기에 IGCC 가스화 플랜트에 대한 FEED 설계 (Front-Eng Engineering Design)를 완료하였다. 그 과정 중 설계조건에 의한 기본 엔지니어링 사항과 석탄 가스화 플랜트에 대한 성능예측 결과를 본 연구에서 소개한다. 가스화 플랜트의 엔지니어링은 가스화 블록과 가스정제 블록으로 구분하여 수행하였다. Process Data를 이용하여 PFD Development, P&ID Generation, Equipment Specification 개발, HAZOP 수행, Architecture Engineering 등의 순으로 FEED 설계를 진행하였다. BOD (Basis of Design)를 기준으로 운전조건별 Heat & Mass Balance와 Process Flow를 재검토하고 각 기기별 운전개념을 반영하여 P&ID를 개발하였다. 그리고 배관, 전기 및 제어에 대한 각종 Diagram 개발과 HSE (Health, Safety and Environment) 관련 설계를 수행하였다. IGCC 1호기의 엔지니어링 수행과 함께 Next 호기 자체설계 역량 확보를 위해 두산중공업은 'DIGITs'로 명명된 개념기본설계 Tool을 개발하고 있다. DIGITs는 공정모델링, 단위기기 개념설계, 공정구성 (Process Configuration) 및 종합 Database Package 형태로 구성된다. DIGITs에 의한 계산 결과 공정사 Process Data 기준시 가스화 블록 출구에서 Syngas HHV와 Syngas 현열은 각각 약 $636MW_{th}$와 약 $18MW_{th}$로, Plant 설계조건 $630MW_{th}$를 만족하는 것으로 예측되었다. 향후 DIGITs는 가스정제 블록 및 주변 BOP 설비 등과 연계한 종합 개념기본설계 Tool로써 개발 진행 중이다.

• Elastomers and Composites
• /
• v.33 no.2
• /
• pp.103-109
• /
• 1998

The determination method of successful operation conditions to control the temperature and pressure in autoclave after non-taping vulcanization process was represented. Heat and mass balances were constructed to predict the mass flow rates of air, steam, and condensed water into or from autoclave when the temperature and pressure in the autoclave were to be controlled in the desired profiles. The balance equations were solved by appropriate mathematics, and the solution was applied to an autoclave system where the temperature and pressure were linearly decreased. The resulting solutions were illustrated in graphs.

• Microbiology and Biotechnology Letters
• /
• v.17 no.3
• /
• pp.241-246
• /
• 1989

Continuous on-line monitoring of cell concentration and growth rate in aerobic batch fermentation process was carried out by analyzing the exhaust gas composition of tormentor with a quadrupole mass spectrometer. From the mass spectrometric analyses of major gaseous components, i.e. $N_2$, $O_2$, $CO_2$ and $H_2O$, and the material balance equations for oxygen and carbon dioxide, oxygen uptake rate (OUR) rind carbon dioxide evolution rate (CER) were instantaneously calculated using a computer (16-bit IBM PC-AT) interfaced to a quadrupole mass spectrometer. The calculated OUR and CER data were used for the estimation of cell concentration and growth rate of Candida utilis during batch culture. It was found that the cell concentration could be satisfactorily estimated from the data of OUR arid CER during the culture and this method could be successfully und for the continuous monitoring of cell growth and growth rate.