• Journal of Advanced Marine Engineering and Technology
• /
• 제35권6호
• /
• pp.835-841
• /
• 2011

해상에서 운영되는 해양 시설물용 파력 발전시스템은 대용량 계통 연계형으로 개발되어 왔다. 그러나 등부표용 파력 발전시스템에는 소용량의 발전시스템이 운영 측면에서 효과적이다. 소형 파력 발전의 경우 단순히 전파 정류하여 축전지에 충전하는 방식(직결 방식)을 주로 사용한다. 본 논문에서는 소형 웰스터빈의 발전 특성을 고려하여 부스터 컨버터 기반의 파력 발전전력제어기를 개발하였다. 직결 방식과 부스터 컨버터 방식의 제어기를 설계하고, 실험을 통하여 그 특성을 비교하였다. 실험 결과 제안하는 제어기가 발전기의 출력전압이 낮은 구간에서 출력특성이 개선되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권7호
• /
• pp.677-684
• /
• 2013

A lot study of convection heat transfer on internal flow has been extensively conducted in the past decades using of high specific surface area, increasing heat transfer coefficient, swirling flow and improving the transport properties. This study concerned with the application of a tangential slot swirl generator for improving heat transfer in a horizontal circular copper tube. The Al particles(about $100{\sim}130{\mu}m$) was employed for this experimental work. 3D PIV(particle image velocimetry) technique has employed to measure velocity profiles of Al particles with and without swirl flow. The copper tube is heated uniformly by winding of a heating coil for heat transfer work, having a resistance of 9 ohm per meter. Experiments are performed in the Reynolds number range of 6,800~12,100 with swirl and without swirl using Al particles. Experimental data for comparison of Nusselt number is presented that of with swirl and without swirl along the test tube for the Reynolds numbers. The Nusselt number is improved with increasing of Reynolds numbers or swirl intensities along the test tube. The Nusselt number with swirl flow is about 60.0% to 119.0% higher than that obtained by the Dittus-Boelter equation.

• 한국정밀공학회지
• /
• 제28권7호
• /
• pp.805-813
• /
• 2011

The dynamic stress of the diesel engine block is analyzed by using flexible-body dynamic analysis. Multiple loadings including the pressure load due to gas combustion, thermal load, and dynamic load are considered. Thermal load is assumed constant, however, pressure load and dynamic load are treated as time dependent. The present work is focused on the dynamic stress analysis, especially on finding critical points of the engine block. The analysis model includes four parts - engine block, generator, bed, and mounts. On the other hand, crank shaft, pistons, and main bearings are excluded from the model. However, their dynamic effects are applied by dynamic forces, obtained in the separate analysis. Dynamic stress is found by using flexible body dynamic analysis, and compared to the measured data.

• Smart Structures and Systems
• /
• 제8권1호
• /
• pp.39-52
• /
• 2011

We are developing a biomimetic robot based on the Sea Lamprey. The robot consists of a cylindrical electronics bay propelled by an undulatory body axis. Shape memory alloy (SMA) actuators generate propagating flexion waves in five undulatory segments of a polyurethane strip. The behavior of the robot is controlled by an electronic nervous system (ENS) composed of networks of discrete-time map-based neurons and synapses that execute on a digital signal processing chip. Motor neuron action potentials gate power transistors that apply current to the SMA actuators. The ENS consists of a set of segmental central pattern generators (CPGs), modulated by layered command and coordinating neuron networks, that integrate input from exteroceptive sensors including a compass, accelerometers, inclinometers and a short baseline sonar array (SBA). The CPGs instantiate the 3-element hemi-segmental network model established from physiological studies. Anterior and posterior propagating pathways between CPGs mediate intersegmental coordination to generate flexion waves for forward and backward swimming. The command network mediates layered exteroceptive reflexes for homing, primary orientation, and impediment compensation. The SBA allows homing on a sonar beacon by indicating deviations in azimuth and inclination. Inclinometers actuate a bending segment between the hull and undulator to allow climb and dive. Accelerometers can distinguish collisions from impediment to allow compensatory reflexes. Modulatory commands mediate speed control and turning. A SBA communications interface is being developed to allow supervised reactive autonomy.

• 한국해양환경ㆍ에너지학회지
• /
• 제18권4호
• /
• pp.282-290
• /
• 2015

부이의 수직운동으로부터 파랑에너지를 추출하는 파력발전기의 추출효율을 극대화하기 위하여 Sheng et al.(2015)이 제안한 래칭 제어기법을 적용하였다. 래칭 제어기법은 부이를 구속하는 래칭 시간을 조절하여 추출효율을 높이는 위상제어 방법이다. 래칭 제어기법을 규칙파중 수직운동하는 부이에 적용한 결과, 공진조건을 만족하지 않았음에도 불구하고 부이의 운동속도와 추출파워는 크게 증가하였다. 부이의 수직운동으로부터 파랑에너지를 흡수하는 파력발전기에 이러한 래칭 제어기법을 도입하면 추출파워의 증가와 더불어 부이의 흘수와 PTO감쇠력을 줄일 수 있어 제작비용을 크게 낮출 수 있다.

• 한국해양환경ㆍ에너지학회지
• /
• 제1권2호
• /
• pp.18-26
• /
• 1998

본 논문은 쇄파와 속도 전단에 의해 발생하는 난류에 의해 해상에 유출된 기름이 유적으로 분해되어 해수면 하로 분산되어 가는 과정을 논하였다. 유막 분산의 역학적 메커니즘을 파악하기 위하여 두 가지 수리실험, 즉 전단발생장치와 조파수조를 이용하여 난류를 발생시켰다. 이러한 실험으로부터 혼합시간이 증가함에 따라 수면에 형성된 유막은 수십 마이크로미터에서 수백 마이크로미터의 입경을 가진 유적으로 분산되었다 뿐만 아니라 유출된 기름의 풍화정도에 따라서 상이한 분산 메커니즘을 나타내는 것을 확인할 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권7호
• /
• pp.935-941
• /
• 2012

This paper describes a study of conventional electrical rig and simulated application of Flywheel Energy Storage system on the power system of the offshore plants with dynamic positioning system with the following aims: improve fuel consumption on engines, prevent blackout and mitigate voltage sags due to pulsed load and fault. Fuel consumption has been analyzed for the generators of the typical drilling rigs compared with the power plant with Flywheel Storage Unit which has an important aid in avoiding power interruption during DP (Dynamic Positioning) operation. The FES (Fly wheel Energy storage System) releases energy very quickly and efficiently to ensure continuity of the power supply to essential consumers such as auxiliary machinery and thrusters upon main power failure. It will run until the standby diesel generator can start and supply the electric power to the facilities to keep the vessel in correct position under DP operation. The proposed backup method to utilize the quick and large energy storage Flywheel system can be optimized in any power system design on offshore plant.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권7호
• /
• pp.869-875
• /
• 2012

In the past decades, extensive studies on convection heat transfer on internal flow have been conducted by using high specific surface area, by increasing heat transfer coefficient and swirl flow, and by improving the transport properties. In this study, we applied a tangential slot swirl generator to improve heat transfer in a horizontal circular copper tube. The Al-Mg particles (approximately $100{\mu}m$ to $130{\mu}m$) were employed for this experimental work. The copper tube was heated uniformly by winding a heating coil with a resistance of 9 ohm per meter for heat transfer. Using Al-Mg particles, experiments were performed in the Reynolds number range of 5,000 to 13,130, with and without swirl. Experimental data transfers or comparisons between Nusselt numbers with and without swirl along the test tube and Reynolds numbers are presented. The Nusselt number is improved by increasing Reynolds numbers or swirl intensities along the test tube.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.169-174
• /
• 2008

Floating devices, such as a cavity resonance device take advantage of both the water motion and the wave induced motions of the floating body itself. The wave energy converter is known commercially as the WAGB(Wave Activated Generator Buoy) and is used in some commercially available buoys to power navigation aids such as lights and horns. This wave energy converter consists of a circular floatation body which contains a vertical center pipe that has free communication with the sea. A theoretical analysis of this power generated by a pneumatic type wave energy converter is performed and the results obtained from the analysis are used for a real wave energy converter for buoy. This paper presents the analysis results and the design method for the WEC(Wave Energy Converter), and the associate results are application to the commercially available WEC for buoy. Maximum performance of WEC occurs at resonance with driving waves. The analysis of WEC is performed with LabVIEW program, and the design method of WEC for buoy is suggested in this paper.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.261-262
• /
• 2006

The effect of tube diameter on heat transfer characteristics of absorber in absorption chiller/heater using LiBr solution as a working fluid has been investigated by experimental study to develop a high performance and compact absorber. A system Includes a tube absorber, a generator, solution distribution system and cooling water system was set up. The diameter of the heat exchanger tube inside absorber was changed from 15.88mm to 12.7mm and 9.52mm. The experimental results show that the heat transfer coefficient, Nusselt number and heat flux increase as solution flow rate and cooling water flow rate increase. The heat transfer performance increases as tube diameter decreases. Among three different tube diameters, the smallest tube diameter 9.52mm has highest heat transfer performance. A comparison of the heat transfer coefficient obtained by the present study with those of previous experimental results showed good overall agreement.