• 한국항공우주학회지
• /
• 제36권4호
• /
• pp.337-345
• /
• 2008

연구에서는 NACA4412익형으로 이루어진 주날개에 NACA0012플랩이 장착된 아음속 벽면효과 모형(SWIM)의 날개 표면 3차원 압력 분포를 압력감응페인트를 이용하여 시험적으로 연구하였다. 한국항공우주연구원의 아음속 풍동에서 레이놀즈수 3.1x105의 조건에서 시험 모형의 받음각 변화에 따른 날개 윗면 및 아랫면의 압력 분포를 측정하였다. 그 결과 받음각이 증가함에 따라 날개 윗면에서의 최저 압력 지점이 뿌리에서 끝단으로 이동을 하는 것을 관찰하였고, 날개 끝단의 뒷전에서도 끝단 와류를 일으키는 압력이 매우 낮은 지점도 관찰되었다. 그러나 실속각 이후인 받음각 15도의 경우 끝단 뒷전에서는 압력이 낮은 지점이 계속 관찰되었으나 그 이외의 부분은 스팬 방향 압력 분포가 편평하였다. 압력감응페인트와 더불어 압력공을 사용하여 날개의 코드 방향 2차원 압력분포도 측정 하여 비교하였고 두 시험에서 측정된 각 압력계수들의 차이의 평균은 약 0.077임을 확인하였다.

• 한국항공우주학회지
• /
• 제35권11호
• /
• pp.1028-1035
• /
• 2007

논문에서는 시험선인 소형 위그선의 주날개 구조를 엔진 및 프로펠러에 의해 유발되는 진동을 가진력으로 하여 강제진동 해석을 수행하였다. 대상 위그선은 2행정의 왕복엔진을 날개에 장착하여 프로펠러에 의한 추력으로 비행하며, 미는 형식(Pusher Type)의 엔진 배열을 취하고 있다. 유한요소해석을 위해서 구조해석 상용프로그램인 MSC/NASTRAN을 사용하였으며, 엔진의 주요 진동 특성인 H-mode 와 V-mode 그리고 X-mode를 특정 가진 주파수로 하여 주파수 응답 해석을 수행하였고, 엔진의 횡방향 진동 모드인 L-mode를 프로펠러의 회전에 의해 진동을 수반하는 가진 추력으로 가정하여 과도응답 해석을 수행한 후 날개의 진동 특성을 살펴보았다.

• 한국항공우주학회지
• /
• 제41권5호
• /
• pp.342-349
• /
• 2013

무인항공기가 외형손상을 입는 경우, 비행역학 특성이 변하기 때문에 손상 이전 설계된 제어기는 더 이상 안정적인 제어성능을 보장하지 않는다. 본 논문에서는 주익의 손상이 일어난 무인항공기에 대해서도 강건한 제어성능을 보장하는 신경회로망 적응제어기법을 소개한다. 구동기의 특성에 의한 제어기의 성능저하를 방지하기 위해 Pseudo Control Hedging (PCH)를 추가적으로 사용하였다. 기체고정좌표계의 중심이 항공기의 무게중심에 위치하지 않는 비대칭 동역학을 사용하였으며, 전익형 무인기를 대상 비행체로 하였다. 날개가 손상되지 않은 모델과 손상된 모델의 풍동시험을 통해 얻은 공력데이터를 이용하여 시뮬레이션을 수행하였다. 시뮬레이션의 결과를 통해 제안된 제어기법이 주익의 손상이 발생한 항공기에 대해서도 여전히 안정적인 조종성능을 보장하는 제어기법임을 검증하였다.

• Composites Research
• /
• 제19권5호
• /
• pp.12-19
• /
• 2006

본 논문에서 한국해양연구원에서 개발 중인 20인승급 소형 위그선의 주익 구조 설계 및 해석에 관한 연구를 수행하였다. 경량화를 위해 탄소/에폭시 복합재료를 적용하였으며, 구조 형태는 스킨 스파 폼 샌드위치 구조를 사용하였다. 개념 설계에는 복합재 설계 개념을 반영하였고, 상세 설계 및 경량화 구조 설계에는 상용 유한 요소 코드인 NASTRAN을 이용하여 구조 설계를 수행하였다. 여러 단계의 구조 설계 변경을 통해 최종 구조 설계 결과는 설계 요구 조건을 만족하는 결과임을 확인하였다. 또한 주익을 동체에 고정하기 위해 8개의 고강도 볼트를 이용한 삽입 볼트형 구조가 용이한 장탈과 20넌 이상의 피로 수명의 고려를 통해 채택되었다.

• Geomechanics and Engineering
• /
• 제19권1호
• /
• pp.49-60
• /
• 2019

Crack instability propagation during coal and rock mass failure is the main reason for electromagnetic radiation (EMR) generation. However, original cracks on coal and rock mass are hard to study, making it complex to reveal EMR laws and mechanisms. In this paper, we prefabricated cracks of different inclinations in coal and rock samples as the analogues of the native cracks, carried out uniaxial compression experiments using these coal and rock samples, explored, the effects of the prefabricated cracks on EMR laws, and verified these laws by measuring the surface potential signals. The results show that prefabricated cracks are the main factor leading to the failure of coal and rock samples. When the inclination between the prefabricated crack and axial stress is smaller, the wing cracks occur first from the two tips of the prefabricated crack and expand to shear cracks or coplanar secondary cracks whose advance directions are coplanar or nearly coplanar with the prefabricated crack's direction. The sample failure is mainly due to the composited tensile and shear destructions of the wing cracks. When the inclination becomes bigger, the wing cracks appear at the early stage, extend to the direction of the maximum principal stress, and eventually run through both ends of the sample, resulting in the sample's tensile failure. The effect of prefabricated cracks of different inclinations on electromagnetic (EM) signals is different. For samples with prefabricated cracks of smaller inclination, EMR is mainly generated due to the variable motion of free charges generated due to crushing, friction, and slippage between the crack walls. For samples with larger inclination, EMR is generated due to friction and slippage in between the crack walls as well as the charge separation caused by tensile extension at the cracks' tips before sample failure. These conclusions are further verified by the surface potential distribution during the loading process.

• 소성∙가공
• /
• 제14권2호
• /
• pp.126-132
• /
• 2005

The isothermal forging design of a Ti-6Al-4V wing shape was performed by 3D FE simulation. The design focuses on near-net shape forming by the single stage. The process variables such as the die design, pre-form shape and size, ram speed and forging temperature were investigated. The main design priorities were to minimize forging loads and to distribute strain uniformly in a given forging condition. The FE simulation results for the final process design were compared with the isothermal forging tests. The instability of deformation was evaluated using a processing map based on the dynamic materials model(DMM), including flow stability criteria. Finally, a modified process design for producing a uniform Ti-6Al-4V wing product without forming defects was suggested.

• 드라이브 ㆍ 컨트롤
• /
• 제14권2호
• /
• pp.37-44
• /
• 2017

In this study, in order to prevent cavitation in a variable swash-plate type hydraulic pump, a basic model impeller has been applied to a new pump, and the impeller shape has been optimized through flow analysis. Based on the analysis results, we could propose an impeller shape with high efficiency and low possibility of cavitation in comparison with the basic model. The simplification of the basic shape of the impeller of the hydraulic pump was performed in three parts in the order of hub shape, wing, and curvature, and eight design parameters were defined to satisfy the design requirement. Compared with the initial model of the impeller, when the differential pressure of the optimum model increased, the efficiency was improved. It achieved the goal of design improvement because cavitation did not occur under the rated operating conditions.

• 한국군사과학기술학회지
• /
• 제15권6호
• /
• pp.738-745
• /
• 2012

Aircraft battle damage repair(ABDR) is emergency repair method for the damaged aircraft in battle field. The main purpose of the ABDR is to increase the readiness of fighter aircraft during wartime. While many studies have been conducted to develop ABDR method, few efforts have focused on evaluation of damage and determination of the size of hole caused by enemy's anti-aircraft artillery attack. The aim of this study is essentially to quantify damage of aircraft wing attacked by anti-aircraft artillery. The computer simulations was performed to accomplish this goal. A number of simulations have been carried out to compare size of damages under various attack conditions. In conclusion, it was revealed that the size of damage varied depending on the type and direction of cannonball. Furthermore, in this paper, the proper path sizes are suggested for different damage conditions.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2023년도 학술발표회
• /
• pp.35-35
• /
• 2023

The main reason for its instability is sediment scouring downstream of hydraulic structures. Both physical and numerical models have been used to investigate the influence of soil properties on scour hole geometry. Nevertheless, no research has been conducted on resistance parameters that affect sedimentation and erosion. In addition, auxiliary structures like wing walls, which are prevalent in many real-world applications, have rarely been studied for their impact on morphology. The hydraulic characteristics of steady flow through a boxed culvert are calibrated using a 3D Computational Fluid Dynamics model compared with experimental data in this study, which shows a good agreement between water depth, velocity, and pressure profiles. Test cases showed that 0.015 m grid cells had the lowest NRMSE and MAE values. It is also possible to quantify sediment scour numerically by testing roughness/d₅₀ ratios (c_s) and diversion walls at a meander flume outlet. According to the findings, c_s = 2.5 indicates a close agreement between numerical and analytical results of maximum scour depth after the culvert; four types of wing walls influence geometrical deformation of the meander flume outlet, resulting in erosion at the concave bank and deposition at the convex bank; two short headwalls are the most appropriate solution for accounting for small changes in morphology. A numerical model can be used to estimate sediment scour at the meander exit channel of hydraulic structures based on the roughness parameter of soil material and headwall type.

• 한국항공운항학회지
• /
• 제25권3호
• /
• pp.35-43
• /
• 2017

Research for solar-powered high altitude long endurance(HALE) UAV was conducted by Korea Aerospace Research Institute(KARI), and the EAV-3 with 19.5m wing span was developed. For HALE flight, aircraft should be lightly designed. Especially, airframe structure that accounts for a large portion of the total weight of aircraft should be lightweight. In this paper, development process of airframe structure for solar-powered HALE UAV, EAV-3, is described briefly. Domestic developed T-800 grade CFRP(Carbon Fiber Reinforced Plastic) composite material with high modulus and strength was used to design main load carrying structures. Flightloads analysis that takes into account large structural deformation was carried out. Stress and flutter analyses for airframe structure sizing were conducted. Static strength test for main wing and aircraft ground vibration test were conducted successfully and structural integrity was secured.