• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.185-188
• /
• 1993

The goal of this paper is to develop an on-board controller for a model helicopter's hovering attitude control, using i8096 one-chip microcontroller. Required controller algorithm is programmed in ASM-96 assembly language and downloaded into an i8096 microcontroller. The performance of hovering flight using this system is verified by experiments with the model helicopter mounted on an instrumented flight stand where 3 potentiometers and an optical proximity sensor measure te attitude and main rotor speed of the helicopter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.400.2-400
• /
• 2002

Recently rotating machines have became high speed and high Power and light weight. Bearings are one of the main components which influence power loss and stability of rotating machines. Appropriate bearing should be selected with considering characteristics of rotating machine. Floating ring journal bearing(FIB) consists of an inner film and outer film, and possess high damping and stability. FJB has been for adopted into turbocharger for the high stability at high operating speed. (omitted)

• Journal of Mechanical Science and Technology
• /
• v.17 no.1
• /
• pp.57-63
• /
• 2003

An eigenvalue design sensitivity formulation of a general nonsymmetric-matrix rotor-bearing system is devised. using the DDM (direct differential method). Then, investigations on the design sensitivities of critical speeds are carried out for an APU turbogenerator with a spline shaft connection. Results show that the dependence of the rate of change of the critical speed on the stiffness changes of bearing models of spline shaft connection points is negligible, and thereby their modeling uncertainty does not present any problem. And the passing critical speeds up to the 4th critical speed are not sensitive to the design stiffness coefficients of four main bearings. Further, the dependence of the rate of change of the critical speed on the shaft-element length changes shows quantitatively that the spline shaft has some limited influence on the 4th critical speed but no influence on the 1st to 3rd critical speeds. With no adverse effect from the spline shaft, the APU system achieves a critical speed separation margin of more than 40% at a rated speed of 60,000 rpm.

• Journal of the Korean Society of Visualization
• /
• v.17 no.1
• /
• pp.78-84
• /
• 2019

A gas turbine is the main equipment of a power plant that generates electricity by high-speed rotation of the rotor in a high-temperature environment. In particular, in the case of medium to large-sized gas turbines, the rotor is composed of a plurality of stages, and each component is exposed to different physical environments. Especially, in the case of the tip clearance of the turbine, it is a very important factor in the performance of the design items and the operation of the stable turbine, and a design considering the physical behavior of all major parts should be done. In this study, we will discuss the process of visualizing the physical behavior of turbine operating conditions and the method of designing tip clearance for stable operation by using commercial finite element analysis program for gas turbine assembly model and single product.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.3
• /
• pp.183-188
• /
• 2014

Power conversion systems used in large gas turbine power plant can be divided into two main part. Because of the initial start-up characteristic of the gas turbine combustor, the gas turbine must be accelerated by starting device(LCI : Load Commutated Inverter) up to 10%~20% of rated speed to ignite it. In addition, the ECS(Excitation Control system) is used to control the rotor field current and reactive power in grid-connected synchronous generator. These two large power conversion systems are located in the same space(container) because of coordination control. Recently, many manufactures develop high speed controller based on function block available in the LCI and ECS with the newest power semiconductor. We also developed high speed controller based on function block to be using these two system and it meets the international standard IEC61131 as using real-time OS(VxWorks) and ISaGRAF. In order to install easily these systems at power plant, main controller, special module and IO module are used with high speed communication line other than electric wire line. Before initial product is installed on the site, prototype is produced and tests are conducted for it. The performance results of Integrated controller and application program(SFC, ECS) were described in this paper. The test results will be considered as the important resources for the application in future.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.6
• /
• pp.1123-1129
• /
• 2009

The main goal of this paper is to simulate a Doubly-Fed Induction Generator (DFIG), which is similar to a real system. Wind velocity data is applied to a 2D Lookup table as a speed reference for a turbine model. A real electric machine's parameters are put in the simulator to get some results of the real system. The Matlab have been generally used to simulate DFIG, but it has some differences from the real system and is difficult to implement. A Simplorer simulator, however, simplifies DFIG simulation. The turbine is directly connected with the DFIG to be close to the real system. The machine's rotor is excited and controlled by the discrete carrier modulated matrix converter. It is possible to retrieve important information, like a generated power and wind quality etc., from the simulator without a huge wind turbine.

• International Journal of Aeronautical and Space Sciences
• /
• v.1 no.2
• /
• pp.22-29
• /
• 2000

A method to simulate the gas turbine transient behavior is developed. The basic principles of the method and main input data required are described. Calculation results are presented in terms of whole operating regime of the engine. The influence of initial parameters such as starting engine power, moment of inertia of the rotor, fuel schedule on performance characteristics of gas turbine during transient operation is shown. In addition, the effect of bleeding air on transient behavior is also considered. For validation of the developed computer code, a comparative analysis with experimental data obtained from a heavy duty gas turbine is made. Calculation results agree well with the experimental data for the range of operating regime studied and proved applicability of the developed technique to initial design stage of control system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.76-83
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including main and rotary ducts, the nozzle subsystem including main and tip jet nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. Transient simulation performance utilized the ICV (Inter-component volume) method and simulated using the SIMULINK. Transient performance analysis was performed on 3 cases. Fuel flow schedules to accelerate from Idle to maximum rotational speed were divided into the step increase of the most severe case and ramp increase cases to avoid the overshoot of turbine inlet temperature, and variations of thrust and the turbine inlet temperature were investigated in some transient analysis cases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.127-132
• /
• 2005

In order to investigate transient behavior, of the CRW(Canard Rotor Wing) type UAV(Uninhabited Aerial Vehicle) propulsion system during flight mode transition considering flow control valve operation, the propulsion system was modelled using SIMULINK commercial program. The valve system is to control the gas flow of the rotary duct system and the main duct system, and the analysis was performed with an assumption that the total gas mass flow of the main engine is the same as summation of the rotary duct flow and the main duct flow, and with consideration of valve loss, flow rate and effective area in valve angle variation. The performance analysis was carried out during flight mode transitions from the rotary flight mode to the fixed wing flight mode and vice versa mode at altitude of 1km, flight Mach number 0.1 and maximum engine rpm.

• Progress in Superconductivity
• /
• v.11 no.1
• /
• pp.57-61
• /
• 2009

A superconductor flywheel energy storage(SFES) system is mainly act an electro-mechanical battery which transfers mechanical energy into electrical form and vice versa. SFES system consists of a pair of non-contacting High Temperature Superconductor (HTS) bearings with a very low frictional loss. But it is essential to design an efficient HTS bearing considering with rotor dynamic properties through correct calculation of stiffness in order to support a huge composite flywheel rotor with high energy storage density. Static properties of HTS bearings provide data to solve problems which may occur easily in a running system. Since stiffness to counter vibration is the main parameter in designing an HTS bearing system, we investigate HTS bearing magnetic force through static properties between the Permanent Magnet(PM) and HTS. We measured axial / radial stiffness and found bearing stiffness can be easily changed by activated vibration direction between PM and HTS bulk. These results are used to determine the optimal design for a 10 kWh SFES.