• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.125-134
• /
• 2015

This is the third paper on the combustion characteristics of the landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine. It is the first in this series to discuss the effects of the torch device on combustion. The results show that an optimum orifice ratio exists regardless of the torch volume, and a few adverse effects on the combustion are observed for an excessively small orifice ratio. In addition, the torch ignition decreases the initial burn duration, and the decrease in the heat transfer caused by this decreased duration contributes to an increase in the peak combustion pressure. Finally, the torch mostly plays a positive role in shortening the main burn duration when the combustion condition is worsened by a lower methane fraction. Yet, the torch decreases the initial burn duration rather than the main burn as the methane fraction increases.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.74-80
• /
• 1992

The purpose of this study is to improve the performance of gasoline engine. Combustion-characteristics orignated from supplying cylinder with fuel-air mixture which was formed by the rise of oxygen-concentration in air with oxygen-enriching membrane have been investigated. The results showed that the poor-limit of oxygen-concentration was increased by shortening combustion-duration because the rise of oxygen-concentration in fuel-air mixture resulted in the promotion of combustion-velocity. Also, the generation of large output of power was expected from combustion in proportion as the amount of oxygen was increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.743-752
• /
• 2013

This is the second paper on the combustion characteristics of landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine, and it discusses the combustion process on the basis of pressure measurements. The results show that the bimodal peak pressure phenomenon, which is caused by the interaction of the heat release and the heat transfer, is more apparent as the mixtures are more favorable to combustion, and the magnitudes of the pressures depend on the unburned fraction. In addition, there exist four main inflection points during heat release owing to variations in the heat transfer area related to flame propagation from the ignition point. Furthermore, the number of inflection points increases as the mixture quality worsens because of the extended burn duration. Consequently, the sophisticated interactions between the heat transfer area changing pattern due to flame propagation and transfer duration might cause very peculiar heat release patterns.

• International Journal of Automotive Technology
• /
• v.3 no.1
• /
• pp.17-26
• /
• 2002

The authors have reported significant reductions in particulate emissions of diesel engines by generating strong turbulence during the combustion process. This study aims to identify optimum conditions of turbulent mixing for effective soot reduction during combustion. The experiments were conducted with a constant volume combustion vessel equipped with abet-generating cell, in which a small amount of fuel is injected during the combustion of the main spray. The jet of burned gas from the cell impinges the main flame, causing changes In the mixing of fuel and air. Observation was made for a variety combinations of distances between spray nozzle and Jet orifice at different directions of impingement. It Is shown that compared with the case without Jet flame soot decreases when the jet impinges. When the jet is very close to the flame, it penetrates the soot cloud and causes little mixing. There were no apparent differences in the combustion duration when the direction of impingement was varied, although the mechanisms of soot reduction seemed different. An analysis of local turbulent flews with PIV (Particle image Velocimetry) showed the relationship between the scale of the turbulence and the size of the soot cloud.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.65-77
• /
• 1996

A small-sized industrial diesel engine was converted to a spark ignited engine and then adapted for fuelling with natural gas. After conversion work, general combustion characteristics of the gas engine(such as ignition delay, main and total combustion durations, and heat release characteristics) were studied as a functio of major engine operating variables such as air to fuel ratio, spark timing, and spark plug type. Some other studies on cyclic variation characteristics in IMEP, Pmax and (dp/dφ)max, and also optimum combustion phasing angle were performed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.367-375
• /
• 1986

On the hypothesis that the unstable intermediates yield by the pre-reaction of auxiliary fuel become an initiator or an explosive center which promotes the chain reaction of main fuel, various organic compounds below $C_{10}$ are injected as an auxiliary fuel prior to main injection. In the previous papers, the effects of the auxiliary fuel additions on the ignition delay period, the stability of flame, the NO concentrations in their exhaust gases have been investigated. In the present paper, to confirm where the most suitable location of lean pre-mixture for the combustion of main fuel is, and how the lean pre-mixture is contacted with main fuel, the effects of the injection timing of auxiliary fuel and the turbulence on combustion processes are investigated. Moreover, from the schlieren and color photographs of flame in the combution field, it could be found that the ignition nuclei are formed in a wider region of main spray, and that these ignition nuclei promote the development of flame, which results in the reduction of flaming duration.

• International Journal of Automotive Technology
• /
• v.8 no.4
• /
• pp.395-402
• /
• 2007

Homogeneous Charge Compression Ignition (HCCI) shows great potential for low $NO_x$ emission but is hampered by the problem of no direct method to control the combustion process. Therefore, HCCI combustion becomes unstable easily, especially at lower and higher engine load. This paper presents a method to achieve diesel-fueled HCCI combustion, which involves directly injecting diesel fuel into the cylinder before the piston arrives at top dead center in the exhaust stroke and adjusting the valve overlap duration to trap more high temperature residual gas in the cylinder. The combustion stability of diesel-fueled HCCI combustion and the effects of engine load, speed, and valve overlap on it are the main points of investigation. The results show that: diesel-fueled HCCI combustion has two-stage heat release rate (low temperature and high temperature heat release) and very low $NO_x$ emission, combustion stability of the HCCI engine is worse at lower load because of misfire and at higher load because of knock, the increase in engine speed aids combustion stability at lower load because the heat loss is reduced, and increasing negative valve overlap can increase in-cylinder temperature which aids combustion stability at lower load but harms it at higher load.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.10
• /
• pp.879-886
• /
• 2013

This study aims to provide helpful suggestions for understanding the effect of high EGR on DME HCCI combustion. This study determined which between oxygen partial pressure and oxygen concentration was the main factor affecting the LTHR heating ratio. Furthermore, EGR and the supercharging effect were investigated. To define the parameters for the EGR ratio and supercharging pressure, a numerical analysis of the chemical reaction was conducted under the following conditions: (1) variation of EGR ratio, oxygen concentration, and oxygen content; (2) variation of oxygen partial pressure while the oxygen concentration was almost constant; and (3) variation of oxygen concentration while oxygen partial pressure was constant with EGR and supercharging. The results show that an increase in EGR reduces the combustion duration. On the other hand, an increase in boost pressure increases the combustion duration. Finally, the EGR and boost pressure affect the amount of increase in LTHR.

• Journal of ILASS-Korea
• /
• v.16 no.4
• /
• pp.167-175
• /
• 2011

The HCCI engines have been known with high efficiency and low pollution and can be actualized as the new internal combustion engines. However, As for(??) the ignition and combustion depend strongly on the oxidation reaction of the fuel, so it is difficult to control auto-ignition timing and combustion duration. Purpose of this paper is creating the database for development of multi-dimensional simulation and investigating the influence of different molecular structure. In this research, the effect of n-heptane mole ratio in fuel (XnH) on the ignition delay from homogeneous charge compression ignition(HCCI) has been investigated experimentally. By varying the XnH, it was possible to ascertain whether or not XnH is the main resource of ignition delay. Additionally, the information on equivalence ratio for varying XnH was obtained. The tests were performed on a RCM (Rapid Compression Machine) fueled with n-heptane and iso-octane. The results showed that decreasing XnH (100, 30, 20, 10,0), the ignition delays of low temperature reaction (tL) and high temperature reaction (tH) is longer. And the temperature of reaction increases by about 30K. n-heptane partial equivalence ratio (fnH) affect on tL.and TL. When ${\phi}$nH was increased as a certain value, tL was decreased and TL was increased.

• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.