• 한국정밀공학회지
• /
• 제26권3호
• /
• pp.40-46
• /
• 2009

Toroidally-wound brushless direct-current (BLOC) machines are compact, highly efficient, and can work across a large magnetic gap. For these reasons, they have been used in pumps, flywheel energy storage systems and left ventricular assist devices among others. The common feature of these systems is a spinning rotor supported by a set of (either mechanical or magnetic) bearings. From the view point of dynamics, it is desirable to increase the first critical speed of the rotor so that it can run at a higher operating speed. The first critical speed of the rotor is determined by the radial stiffnesses of the bearings and the rotor mass. The motor also affects the first critical speed if the rotor is displaced from the rotating center. In this paper, we analytically derive the flux density distribution in a toroidally-wound BLOC machine and also derive the negative stiffness of the motor, based on the assumption that the rotor displacement perturbs the flux density distribution linearly. The estimated negative stiffness is validated by finite element analyses.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.170-177
• /
• 1998

The purpose of superconducting magnetic bearing flywheel energy storage system(SMB-FESS) is to store unused nighttime electricity as kinetic energy and convert it to electricity during daytime. The SMB-FESS is proposed as an efficient energy storage system because there is no mechanical problems, such as friction and wear The flywheel over SMB is rotated at a high speed, 50,000rpm. The major source of energy loss in the SMB-FESS is vibration of flywheel. Therefore, the vibration characteristics of SMB-FESS should be identified. In this study, the axial/radial stiffness and damping coefficient of SMB are measured by a vibration test. Natural frequencies and natural modes of flywheel and magnet are analyzed by a finite element method. The modal analysis of system is performed using the modal parameters of each component and the measured stiffness/damping coefficient. So, natural at frequencies and mode shapes of the joined system can be obtained. According to critical speed analysis, the system has two rigid conical modes in the low speed range. Nevertheless, the system has not been affected by the critical speed in the main operating range.

• 제어로봇시스템학회논문지
• /
• 제2권3호
• /
• pp.181-187
• /
• 1996

A frictionless positioning device using cone-shaped active magnetic bearings(AMBs) is developed, which is driven by a brushless DC motor equipped with resolver. The cone-shaped AMB feature that the structure is simple and yet the five d.o.f. rotor motion is controlled by four magnet pairs. A linearized dynamic model, which accounts for the relationship between input voltage and output current in the cone-shaped magnet, is developed and the azimuth motion of the frictionless positioning device is modeled as the second order system. The feedback controller is designed by using linear quadratic regulator with integral action optimal control law so that the cone-shaped AMB system is stabilized and the frictionless positioning device gets the zero steady state. It is observed that the linearized dynamic model is adequate and the frictionless positioning device can achieve the tracking accuracy within the sensor resolution.

• Progress in Superconductivity
• /
• 제5권2호
• /
• pp.141-143
• /
• 2004

For designing a flywheel system using superconductor, it is necessary to understand the basic characteristics of the classical superconductor bearing. It is difficult to expect the characteristics of superconductor bearings using models that have been introduced up to now. In the "Frozen image" concept, the farce between the permanent magnet and the superconductor can be divided into two forces between permanent magnet and two imaginary magnets in the superconductor; one represents attraction farce and the other represents a repulsion force. We calculated the characteristics of two superconductor bearings, such as an axial, the radial stiffness and the levitation force. This calculation method was very helpful to expect the characteristics of the superconductor bearings. Using this model, we established the optimum condition for the superconductor bearing.r bearing.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2082-2088
• /
• 1995

In this paper, we designed and fabricated the magnetic bearings and built-in type cylindrical capacitive transducers for improving the vibration characteristics of rotating shaft. The eddy current and magnetic field from the electromagnet of the bearing don't affect the measuring signal of the capacitive type transducers so that it is possible to locate the capacitive sensor plates around the magnetic bearing poles and can improve the spillover problem which is induced by the noncollocation of the sensors and actuators. According to the sensitivity calibration schemes using a X-Y table, the cylindrical capacitive transducers have a good linearities in the .+-.70.mu.m range from the geometric center of the sensor plates. The measured results also show high displacement sensitivities of the sensors. According to the performance test of the magnetic bearing which is controlled by the analog PD controllers, we found that the built-in capacitive transducer system successfully measures the journal displacement in the magnetic field and therefore the magnetic bearing system supports the rotating shaft up to 12,000 rpm.

• 한국정밀공학회지
• /
• 제20권7호
• /
• pp.91-98
• /
• 2003

In the field of precision manufacturing demanding high positioning performance, the mechanical friction in positioning device deteriorates the quality of the product and increases the cost of production for positioning devices. Therefore, we propose a contract-free linear actuator using active magnetic bearing. The structure and operating principle of the proposed system are explained, and the magnetic forces are analyzed by magnetic circuit theory to design magnetic bearings and linear actuator. With the derived equation of motion, the stability is identified. Experimental results are presented to show the feasibility.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권1호
• /
• pp.13-19
• /
• 2002

Although the design of magnetic bearing needs a systematic optimization due to several design variables, constraints, geometric limitations, nonlinearities, and so on, the present designs for magnetic bearings have been conducted in the linear region of the characteristics for magnetic materials by trial and error considering design constraints. This article, therefore, provides the possibility of a genetic algorithm(GA) based optimization with two dimensional nonlinear finite element magnetic field analysis for the design of a radial heteropolar magnetic bearing. The magnetic bearing design by GA based optimization makes good agreements with that by a commercial optimization software DOT using the sensitivity analysis.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.53-58
• /
• 1999

Although the design of magnetic bearing needs a systematic optimization du e to several design variables, constraints, geometric limitations, nonlinearities, and so on, the present for magnetic bearings have been conducted in the linear region of the characteristics for magnetic by trial and error considering design constraints. This article, therefore, provides the possibility of a genetic algorithm(GA) based optimization with two dimensional-nonlinear finite element magnetic field analysis for design of a radial heteropolar magnetic bearing. The magnetic bearing design by GA based optimization makes good agreements with that by a commercial optimization software DOT using the sensitivity analysis.

• 동력기계공학회지
• /
• 제16권3호
• /
• pp.64-68
• /
• 2012

Because the magnetic bearing supports levitating body without contact, wear, noise and vibration are very small comparing with mechanical bearings, it is very useful to high revolution machinery. In general, the magnetic attractive force function that is proportional to square of control current(x), and inversely proportional to square of an air gap(i) has been widely used. This paper proposed the new magnetic attractive force function that is proportional to cube of the control current, and inversely proportional to square of the air gap. The function was optimized to minimize the cost function that is the percentage of deviation about the change of a proportional constant(k), using the experimental data, ie, control currents and air gaps.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.304-308
• /
• 2004

One of the obstacles for a magnetic bearing to be used in the wide range of industrial applications is the failure modes associated with magnetic bearings. These failure modes include power amplifier faults, position sensor faults, and the malfunction of controllers. Fault-tolerant magnetic bearing systems have been proposed so that the system can operate in spite of some faults. In this paper, we designed and tested a fault-tolerant magnetic bearing system. The system can cope with the actuator faults as well as the faults in position sensors, which are the two major fault modes in a magnetic bearing system.