• Journal of the Korean Professional Engineers Association
• /
• v.22 no.3
• /
• pp.5-13
• /
• 1989

A major problem of stopwatch time study is how to do for the accurate and consistent performance rating, which is one of the critical variables to determine the accuracy of work measurement and should be still dependent upon time observer's judgement. Therefore the time observer's ability for the performance rating is very important, and must be improved by correct training method and procedure. This paper developed a new benchmark and benchmark-observation method for the effective performance rating training of assembling and machining operations. The trainees' ability in the accuracy and consistency of the performance rating ,improved significantly after being trained by subject method. The percentage improvement in rating accuracy and consistency values was 34.7% and 49% respectively. In addition, benchmark-practice method for the performance rating training is not significant, so it is proofed that the skill of a certain operation is not important for the improvement of the rating ability.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.240-245
• /
• 2000

This paper presents the experimental study of drilling for duralumin A2024 with intermittently decelerated feed rate. It is achieved through a programmed periodic increase and decrease in the feed rate using a machining center. The following experimental result were performed with the objective of solving chip to disposal problems. In conventional drilling of aluminum, long continuous chips are produced that wind around the drill causing difficulties in eliminating chips from the cutting zone. In order to acquire the basic data necessary to regulate the chip profile, the relationship between cutting variables and chip shape was investigated. The following conclusions are established from the experimental results. At a suitable feed fluctuation ratio, intermittently decelerated feed drilling proved successful in breaking chips to appropriate lengths while maintaining stable cutting. Thus, it is an effective method for improving chip disposal. The amplitude of the dynamic component of cutting force in intermittent feed frilling is influenced by the feed fluctuation ratio.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.103-110
• /
• 2000

Experimental study of drilling for duralumin A2024 was conducted with intermittently accelerated and decelerated feedrate. It is achieved through a programmed periodic increase and decrease in the feedrate using a machining center. The following experimental results were performed with the objective of solving chip to disposal problems. In conventional drilling of aluminum, long continuous chips are produced with winding around the drill and causing difficulties in eliminating chips from the cutting zone. In order to acquire the basic data necessary to regulate the chip profile, the relationship between cutting variables and chip shape was investigate. The following conclusions are established from the experimental results. At a suitable feed fluctuation ratio, intermittently decelerated feed drilling proved successful in braking chips to appropriate lengths while maintaining stable cutting. Thus, it is an effective method for improving chip disposal. The amplitude of the dynamic component of cutting force in intermittent feed drilling is influenced by the feed fluctuation ratio.

• Journal of the Korea Convergence Society
• /
• v.9 no.5
• /
• pp.145-150
• /
• 2018

In the machine tool spindle, various tasks ranging from roughing to finishing must be possible, and the functions of constant speed movement or rotation positioning must be performed. Therefore, there are many variables to be considered in the spindle design. The Swiss Turn Type spindle automatic lathe is a good machine tool for working pins with thinner shafts than a fixed automatic lathe. The Swiss Turn Type spindle is mainly used for precision machining of small products, so the machining precision should be high. The maximum outer diameter limit shall be Ø32 and the inner diameter limit shall be Ø6. In this study, the static and dynamic characteristics of the SCM440 material used in the spindle type automatic lathe were analyzed by applying it to the Swiss turn type spindle automatic lathe. Numerical analysis was used to obtain optimal design technique with high speed and high accuracy considering the factors affecting the static and dynamic characteristics of the spindle.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.46-59
• /
• 1998

This paper presents shape design, surface construction, and cutting path generation for the surface of marine ship propeller blades. A propeller blade should be designed to satisfy performance constraints that include operational speed which impacts rotations per minutes, stresses related to deliverable horst power, and the major length of the marine ship which impacts the blade size and shape characteristics. Primary decision variables that affect efficiency in the design of a marine ship propeller blade are the blade diameter and the expanded area ratio. The blade design resulting from these performance constraints typically consists of sculptured surfaces requiring four or five axis contoured machining. In this approach a standard blade geometry description consisting of blade sections with offset nominal points recorded in an offset table is used. From this table the composite Bezier surface geometry of the blade is created. The control vertices of the Hazier surface patches are determined using a chord length fitting procedure from tile offset table data. Cutter contact points and path intervals are calculated to minimize travel distance and production time while maintaining a cusp height within tolerance limits. Long path intervals typically generate short tool paths at the expense of increased however cusp height. Likewise, a minimal tool path results in a shorter production time. Cutting errors including gouging and under-cut, which are common errors in machining sculptured surfaces, are also identified for both convex and concave surfaces. Propeller blade geometry is conducive to gouging. The result is a minimal error free cutting path for machining propeller blades for marine ships.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.317-324
• /
• 1998

TiN and TiCN films were deposited on the high speed steel by Cathode Arc Ion Plating(CAIP) Process to investigate the tool life extension effect. The experiment variables were bias voltage and deposit time for the TiN coating and reactive gas flow rate ($CH_4:N_2$) under fixing deposit pressure, are current, bias voltage for the TiCN coating respectively. The micro structure and mechanical properties were investigated and compared for among the coating conditions using various methods and machining practice.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.7
• /
• pp.140-147
• /
• 1996

Machining accuracy of machine tools spindles using the hydrostatic bearing, largely depends on the static stiffness and the thermal deformation of the spindle unit. In this paper, the modelling and static, thermal analysis of the hydrostatic spindles were performed for the relationship between the design variables like the bearing span, overhang, bearing stiffness and static stiffness at spindle. The goal of optimization is the mazimum, static stiffness at spindle nose with lower temperature rise in hydrostatic bearing. Temperature rise of hydrostatic bearing is minimized with the variables of spindle diameter and oil supply pressure. Finally, validity of the proposed algorithm is verified by improving the static, thermal performance of the existing hydrostatic spindles.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.3
• /
• pp.65-73
• /
• 2015

This paper presents a method of predicting the machining parameters on the turning process of low carbon steel using a neural network with back propagation (BP) and particle swarm optimization (PSO). Cutting speed, feed rate, and depth of cut are used as input variables, while surface roughness and electric current consumption are used as output variables. The data from experiments are used to train the neural network that uses BP and PSO to update the weights in the neural network. After training, the neural network model is run using test data, and the results using BP and PSO are compared with each other.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.926-931
• /
• 2001

In this paper a CAD-based optimal design system is introduced and applied to optimal design of machine tool structures. The system is designed to reduce manual interfacing effort. All the design activities such as selecting design variables, making FE meshes and FE analysis are integrated on a parametric CAD program. A user can easily select design variables by clicking a CAD model. To enhance the robustness and versatility, this system uses the finite difference method for the design sensitivity analysis. By taking a practical example of the design of the column of a horizontal machining center, it is shown that the software system is efficiently usable in industry establishing the goal of minimizing user intervention between various analysis and optimization activities.

• Journal of the Korea Safety Management & Science
• /
• v.3 no.1
• /
• pp.117-125
• /
• 2001

Polyacetal resin is usually used to make molds, but it is difficult to achieve dimension accuracy during molding. Therefore it is usually necessary to cut the polyacetal resin after a molding process. Polyacetal resin is easily machining by standard machine tool. Acetal is also a thermal stable material which can be totted without coolant Another concern about the use of polyacetal resin is that it absorbs water easily, which also results in problems with dimension accuracy Therefore, in this study, the cutting resistance of water-absorbed polyacetal resin and its surface roughness after cutting in order to achieve the highest degree of accuracy in the cutting of polyacetal resin were investigated. Also, The Robust Design method uses a mathematical tool called orthogonal arrays to study a large number of decision variables with a small number of experiments. It also uses a new measure of quality, called signal-to-noise (S/N) ratio, to predict the quality from the customer's perspective. Thus, we have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.