• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.343-348
• /
• 2000

The term‘High Speed Machining’has been used for many years to describe end milling with small diameter tools at high rotational speeds. typically 10,000 - 100,000 rpm. The process was applied in the aerospace industry for the machining of light alloys, notably aluminium. In recent years, however, the mold and die industry has begun to use the technology for the production of components, including those manufactured from hardened tool steels. And the end-mill is an important tool in the milling process. A typical examples for the end mill is the milling of pocket and slot in which a lot of material is removed from the workpiece. Therefore the proper selection of cutting parameters for end milling is one of the important factors affecting the cutting cost. The one of the advantages of HSM is cutting thin-wall part of light alloy like Al (thinkness about 0.3mm). In this paper, firstly, we study characteristics of HSM, and then, we choose the optimal parameters(cutting forces) and investigate various machining strategies to cut thin-wall part by experiment.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.7-11
• /
• 2014

The experimental analysis presented aims at the selection of the most optimal machining parameter combination for wire electrical discharge machining (WEDM) of STD11. Based on the Taguchi experimental design ($L_{27}$ orthogonal array) method, a series of experiments were performed by considering time-on, voltage, time-off, wire speed, and flow rate as input parameters. The surface roughness was considered responses. Based on the signal-to-noise (S/N) ratio, the influence of the input parameters on the responses was determined. The optimal machining parameters setting for the minimum surface roughness was found using Taguchi methodology. In order to investigate the effects of process parameters on the surface machined by WEDM, Several experiments are conducted to consider effects of time-on, voltage, time-off, wire speed and flow rate on the surface roughness. Analysis of variance (ANOVA) as well as regression analysis are performed on experimental data. The best results of surface roughness were obtained at higher voltage, lower wire speed, and lower time-on.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.101-106
• /
• 2002

This paper presents an experimental investigation of high speed machining of dies and molds. Several critical issues involved with the high speed machining of QRO90 tool steel of hardness up to HRc62, have been studied and explained from a detail analysis of experimental observations. The experiments were performed using ball end mills. The effect of different process parameters on tool life and surface finish produced was also investigated. The cutting parameters involved were; cutting speeds in the range of 100 to 40 / m/min, axial depth of cut from 0.1 to 0.5mm, pick feed of 0.1 to 0.5mm. Run out and acceleration signals were observed during the experiment to investigate cutting slates. Compressed air and flood coolant were used and the effect of coolant on tool life was also determined.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.73-80
• /
• 2006

High speed machining(HSM) technique is widely used in the appliance, automobile part and mold industries, because it has many advantages such as good quality, low cost and rapid machining time. But it also has problems such as tool breakage, smooth tool path, and so on. In particular, small size end mill is easy to break, so it must be changed before interrupting operation. Generally, the tool life of small size end mill is affected by the milling conditions whose selected parameters are spindle speed, feedrate, and width of cut. The experiments were carried out by full factorial design of experiments using an orthogonal array. This paper shows optimal combination and mathematical model for tool life, Therefore, the analysis of variance(ANOVA) is employed to analyze the main effects and the interactions of these milling parameters and the second-order polynomial regression model with three independent variables is estimated to predict tool life by multiple regression analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.351-358
• /
• 1993

Recently a high speed spindle system for machine tools has attracted considerable attention to reduce the machining time, to improve the machining accuracy, to perform the machining of light metals and hard materials and to unite the cutting and grinding processes. In this study, a high speed spindle system is developed by applying the oil-air lubrication method, angular contact ball bearings, injection nozzles with dual orifices and so on. And a lubrication experiment for evaluating the performance of the spindle system is carried out. Especially, in order to establish the lubrication conditions related to the development of a high speed spindle system, the effects of oil supply rate, rotational spindle speed and so on are studied and discussed on the bearing temperature rise, bearing temperature distribution and frictional torque. And the effect of spindle system structure on the bearing temperature distribution is investigated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.20-25
• /
• 2011

In this paper, we reviewed the spindle system's motor and bearing and its mode safety for optimal design of a high speed spindle system that exceeds DmN value of 1,500,000. We could verify that it has a separation margin during critical speed by performing critical speed analysis. Also, we have selected an optimal sensoring installation location and actually manufactured & installed the sensor by identifying the stress concentration position in the axial load through finite element analysis to install the built-in piezo electric type load sensor to the spindle housing that can measure and monitor the machining load during high speed rotation of the spindle. Reproducibility is also verified by calibrating the error through the sensor's sensitivity adjustment after comparing the output between the plate dynamoneters and the load sensor to confirm the reproducibility of the load sensor.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.192-197
• /
• 2002

In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.123-128
• /
• 1994

A high speed spindle system for machine tools can be used to reduce the machining time, to improve the machining accuracy, to perform the machining of light metals and hard materials, and to unite the cutting and grinding processes. In this study, a high speed spindle system is developed by applying the oil-air lubrication method, angular contact ball bearings, injection nozzles with dual orifices, cooling jacket and so on. And an air cooling experiment for evaluating the performance of the spindle system is carried out. Especially, in ofder to establish the air cooling conditions related to the development of a high speed spindle system, the effects of cooling air pressure, oil supply rate, air supply rate and rotational spindle speed are studied and discussed on the bearing temperature rise and frictional torque. Also the effects of cooling air pressure, rotational spindle speed and spindle system structure is investigated on the bearing temperature distribution. The experiment on the test model reveals the usefulness of the air cooling method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.71-78
• /
• 2020

The rotary feed axes of a 5-axis machine tool can increase the freedom of the tool posture, while reducing feed speed and rigidity. In addition, as a ball-end mill is inevitably used during machining by rotational feed, the step-over length is reduced compared to the flat-end mill, thereby reducing the material removal rate. Therefore, this study attempts to improve the material removal rate, feed speed, and machining stability using the corner radius flat-end mill and a fixed controlled machining method for the rotary feed axes during roughing. In addition, the tapered ball-end mill and simultaneously controlled machining method for the rotary feed axes were used for finishing to improve the propeller's 5-axis machining efficiency by enhancing the surface quality. In order to create the tool path effectively and easily, we propose a specific approach for using the propeller's geometric properties and evaluate the effectiveness of the proposed method by comparing it with the method of the dedicated module.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.63-70
• /
• 2020

Two rotational motions of the 5-axis machine tool maximize the degree of freedom of the tool axis vector, which improves tool accessibility; however, this lowers feed speed and rigidity, which impairs machining stability. In addition, cutting efficiency is lowered when compared with a flat end mill because typically, the ball-end mill is used when machining by rotational motion. This study increased cutting efficiency by using a corner radius flat end mill during impeller roughing. Furthermore, we proposed a fixed controlled machining of the rotary motion using geometric shape information to improve the feed speed and machining stability. Finally, we proposed a finishing tool path generation method using a vector net to increase the convenience and practicality of tool path generation. To verify its effectiveness, we compared the machining time, shape accuracy, and surface quality of the proposed method and an existing dedicated module.