• Journal of Biosystems Engineering
• /
• 제25권3호
• /
• pp.195-202
• /
• 2000

This study was conducted to recognize a possibility that cone index can be used as a means of evaluating the tillage workability. Cone indexes were measured every 24 hours after rainfall at the experimental plots, and the rotary and plowing operations were conducted at the same time. The workability was evaluated on a basis of three categories of good, fair and poor depending on the quality of the performed works. Although the workability was affected by many factors such as soil type, moisture content ground slope and weather condition, the duration and amount of rainfall were of most influence. Results of the study showed that a good workability was resulted from the cone indexes greater than an average of 552 kPa for rotary operations and 671 kPa for plowing operations. Fair work was obtained with cone indexes greater than an average of 331 kPa for rotary operations and 459 kPa for plowing operations. The cone indexes less than an average of 171 kPa and 149 kPa resulted in poor workabilities for rotary and plowing operations, respectively. The experimental results may provide a general guideline for evaluating the tillage workability by cone index.

• 비파괴검사학회지
• /
• 제12권3호
• /
• pp.7-11
• /
• 1992

Accurate measurement of green density of compacted part in the powder metallurgy industry is rather fundamental but extremely important process that decide the quality of the sintered part. In case of green sheet P/M product, the green density as well as the distribution of the density must be examined for the same reasons. Currently in most cases, density measuring process is being performed applying conventional Archimedes principles. However this method is not only time-consuming but also often inaccurate because of the inherent nature of the process, such as part sectioning, closing of surface porosity with wax and weighing in air and in water. Therefore, it is necessary to develop a faster and more accurate method to measure the density of green sheet P/M product. In this work, a nondestructive density measurement device using gamma-ray absorption principles was constructed and the optimum condition for measuring green density of P/M sheet and its distribution was sought. The results showed that this method was very effective in terms of measuring time and accuracy.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.722-728
• /
• 2000

This study of field control machine in the recycled vinyl rail is gantry crane type and promoting agricultural automatization through self-controlled spraying, harvesting and conveyance. In addition to, that control machine could get a cost and labor reduction effect through automatization and make better environment by preventing farmers from agrichemical damage, accidents and recycling wasted vinyl. That machine is able to be divided as traveling, spraying, harvesting and conveyance sections. In driving section consists of girder frame, carrier, rail, control system, driving system, working machine, rail and loading device for working machine. This machine has following advantages to be able to bring a big innovation in the agricultural industry. I) Accurate performance is able to be done by proper positioning due to based on the rails. 2) The soil is not made hard like heavy tractor 3) The wheel is not sank into the soil and slipped well under rain like heavy tractor. Therefore, weather and soil situation could not affect working condition. 4) Complete unmanned control and 24hours-working are available due to traveling on the rails. 5) It could use various energy resources like not only liquid fuel but also solar, common electronic power due to traveling on the rails.

• International Journal of Fluid Machinery and Systems
• /
• 제4권3호
• /
• pp.317-323
• /
• 2011

Mini centrifugal pumps having a diameter smaller than 100mm are employed in many fields; automobile radiator pump, ventricular assist pump, cooling pump for electric devices and so on. Further, the needs for mini centrifugal pumps would become larger with the increase of the application of it for electrical machines. It is desirable that the mini centrifugal pump design be as simple as possible as precise manufacturing is required. But the design method for the mini centrifugal pump is not established because the internal flow condition for these small-sized fluid machines is not clarified and conventional theory is not suitable for small-sized pumps. Therefore, we started research on the mini centrifugal pump for the purpose of development of high performance mini centrifugal pumps with simple structure. Three types of rotors with different outlet angles are prepared for an experiment. The performance tests are conducted with these rotors in order to investigate the effect of the outlet angle on performance and internal flow condition of mini centrifugal pumps. In addition to that, the blade thickness is changed because blockage effect in the mini centrifugal pump becomes relatively larger than that of conventional pumps. On the other hand, a three dimensional steady numerical flow analysis is conducted with the commercial code (ANSYS-Fluent) to investigate the internal flow condition. It is clarified from the experimental results that head of the mini centrifugal pump increases according to the increase of the blade outlet angle and the decrease of the blade thickness. In the present paper, the performance of the mini centrifugal pump is shown and the internal flow condition is clarified with the results of the experiment and the numerical flow analysis. Furthermore, the effects of the blade outlet angle and the blade thickness on the performance are investigated and the internal flow of each type of rotor is clarified by the numerical analysis results.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.413-422
• /
• 1993

Air shipment affords the quickest possible delivery of horticultural products. The price of air shipped horticultural products are relatively high as most of these products are perishable. Usually the temperature in the cargo compartment is not controlled during flight. Thus, special attention should be paid to procooling prior to shipment. The environmental condition during transportation of horticultural products is an essential parameter for maintaining the quality of perishable products. Commonly horticultural products were loaded by ULD(Unit Load Devices) as a container or pallet in the aircraft (except for small aircraft) . Therefore, inside temperature of the container and cargo compartment came into question. Scarce literature on the relationship between environmental condition and quality changes of horticultural products during air shipment can be found. By the stand point of keeping fresh quality, investigations on the actual condition of air shipments were carried out to improve the technique during the distribution process of fresh horticultural products. Temperature, humidity, atmospheric pressure, carbon dioxide, ethylene, impacts, and changes in quality during the air shipment of snapbeans, okras and chrysanthemums were measured. Temperature was measured by recording thermometers, relative humidity by recording hygrometers, atmospheric pressure by a strain -guage type pressure sensor, carbon dioxide by testing tubes, ethylene by sampling bags and a gaschromatograph, impacts and vibrations by impact recorders and a 3D accelerometer. Relationships between environmental conditions and quality changes during air shipments were clarified. It was expected from investigations into actual shipments that the ventilation and insulation properties of air freight containers were related to the quality of agricultural products. Aircraft can no directly load and unload trucks into them. The transshipment is inclined to cause shocks and vibrations, and to invite damages within a short time.

• Journal of Biosystems Engineering
• /
• 제41권4호
• /
• pp.313-318
• /
• 2016

Purpose: This study measured and analyzed the PTO (power take off) torque of a transplanter according to the planting conditions during field operation. Methods: A torque measurement system was constructed with torque sensors to measure the torque of a PTO shaft, a measurement device to acquire sensor signals, and a power controller to provide power for a laptop computer. The field operation was conducted at four planting distances (26, 35, 43, and 80 cm) and two planting depths using the transplanter on a field with similar soil conditions. One-way ANOVA with planting distance and Duncan's multiple range test at a significance level of 0.05 were used to analyze the PTO torque. The torque ratio was calculated based on the minimum torque using the average PTO torque measured under each planting condition. Results: The average torques on the PTO shaft for planting distances of 26, 35, 43, and 80 cm at a low planting depth were 11.05, 9.07, 7.04, and 3.75 Nm, respectively; the same for planting distances of 26, 35, 43, and 80 cm at a middle planting depth were 12.20, 9.86, 7.94, and 4.32 Nm, respectively. When the planting distance decreased by 43, 35, and 26 cm, the torque ratio at a low planting depth increased by 88, 142, and 195%, respectively. When the planting distance decreased by 43, 35, and 26 cm, the torque ratio at the middle planting depth increased by 84, 128, and 182%, respectively. Conclusions: PTO torque fluctuated by planting distance and depth. Moreover, the PTO torque increased for short planting distances. Therefore, farmers should determine the planting conditions of the transplanter by considering the load and durability of the machine. The results of this study provide useful information pertaining to the optimum PTO design of the transplanter considering the field load.

• 산업경영시스템학회지
• /
• 제22권52호
• /
• pp.171-180
• /
• 1999

Industrial equipment reliability improvement and maintenance is gaining attention as the next great opportunity for manufacturing productivity improvement. Reactive maintenance is expensive because of extensive unplanned downtime and damage to machinery. To avoid such an unplanned machine downtime, it is needed to use proactive maintenance approach by either using historical maintenance data or by sensing machine conditions. This paper discusses failure diagonosis and prediction based on the condition-based maintenance and reliability technique. Thus, by enabling such a framework, it can bring us more efficient planning and execution of maintenance to reduce costs and/or increase profits.

• 한국기계연구소 소보
• /
• 통권20호
• /
• pp.89-104
• /
• 1990

This study was carried out to obtain the most optimum conition in vacuum sintering of M2 HSS powder, by analysis of sintering characteristics and fracture strength in several conditions. The conclusion deduced from this study are as follows; -Boron was more effective element than graphite; at this time, the optimum amount of addition was 0.05 wt% -The optimum condition of sintering temperature and time were 1190- $1200^{\circ}C$ and 1-1.25hr, respectively -Fracture strength of vacuum sintered and heat-treated specimen in the most optimum condition was 2-2.5KN/ $mm^2$

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권4호
• /
• pp.50-53
• /
• 2012

This paper describes experimental study on GM-type pulse tube refrigerator (PTR). In a PTR, the pulse tube is only filled with working gas and there exists secondary flow due to a large temperature difference between cold-end and warm-end. The stability of secondary flow is affected by orientation of cold-head and thus, the cooling performance is deteriorated by gas mixing due to secondary flow. In this study, a single stage GM-type pulse tube refrigerator is fabricated and tested. The cooing performance of the fabricated PTR is measured as varying cold-head orientation angle and the results are used as reference data. Then, we divided interior space of pulse tube into three segments, and fixed the various size of screen mesh at interface of each segment to suppress the performance degradation due to secondary flow. For various configuration of pulse tube, no-load test and heat load test are carried out with the fixed experimental condition of charging pressure, operating frequency and orifice valve turns. From experimental results, the fine screen mesh shows the effective suppression of performance degradation for the large orientation angle, but the use of screen mesh cause the loss of cooling capacity rather than the case of no insertion into pulse tube. It should be compromised whether the use of screen mesh in consideration of the installation limitation of a GM-type pulse tube refrigerator.

• 한국연소학회지
• /
• 제19권3호
• /
• pp.1-7
• /
• 2014

Experimental study has been carried out to understand combustion characteristics of a swirl-stabilized premixed gas turbine combustor for power generation. $NO_x$ and CO emissions, extinction limit, pressure loss, and temperature distribution were measured for various operating conditions. Results show that, with increasing inlet air temperature, $NO_x$ is increased due to a higher adiabatic flame temperature while CO is increased or decreased for low or high A/F ratio regime, respectively. depending on the flame location. With decreasing load from the design condition, $NO_x$ is decreased as thermal load is reduced. With further decreasing load, however, $NO_x$ is increased due to a longer residence time. CO is decreased and then increased with decreasing load. Flame extinction limit is extended with increasing inlet air temperature as the recirculation strength is enhanced.