• Progress in Superconductivity and Cryogenics
• /
• v.14 no.4
• /
• pp.50-53
• /
• 2012

This paper describes experimental study on GM-type pulse tube refrigerator (PTR). In a PTR, the pulse tube is only filled with working gas and there exists secondary flow due to a large temperature difference between cold-end and warm-end. The stability of secondary flow is affected by orientation of cold-head and thus, the cooling performance is deteriorated by gas mixing due to secondary flow. In this study, a single stage GM-type pulse tube refrigerator is fabricated and tested. The cooing performance of the fabricated PTR is measured as varying cold-head orientation angle and the results are used as reference data. Then, we divided interior space of pulse tube into three segments, and fixed the various size of screen mesh at interface of each segment to suppress the performance degradation due to secondary flow. For various configuration of pulse tube, no-load test and heat load test are carried out with the fixed experimental condition of charging pressure, operating frequency and orifice valve turns. From experimental results, the fine screen mesh shows the effective suppression of performance degradation for the large orientation angle, but the use of screen mesh cause the loss of cooling capacity rather than the case of no insertion into pulse tube. It should be compromised whether the use of screen mesh in consideration of the installation limitation of a GM-type pulse tube refrigerator.

• Journal of the Korean Society of Combustion
• /
• v.19 no.3
• /
• pp.1-7
• /
• 2014

Experimental study has been carried out to understand combustion characteristics of a swirl-stabilized premixed gas turbine combustor for power generation. $NO_x$ and CO emissions, extinction limit, pressure loss, and temperature distribution were measured for various operating conditions. Results show that, with increasing inlet air temperature, $NO_x$ is increased due to a higher adiabatic flame temperature while CO is increased or decreased for low or high A/F ratio regime, respectively. depending on the flame location. With decreasing load from the design condition, $NO_x$ is decreased as thermal load is reduced. With further decreasing load, however, $NO_x$ is increased due to a longer residence time. CO is decreased and then increased with decreasing load. Flame extinction limit is extended with increasing inlet air temperature as the recirculation strength is enhanced.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.331-341
• /
• 2018

Purpose: This study was conducted to develop a linear Proportional-Integral-Derivative (PID) control algorithm for the ascending and descending system of a rice transplanter and to analyze its response characteristics. Methods: A hydraulic model using a single-acting actuator, proportional valve and a PID control algorithm were developed for the ascending and descending system. The PID coefficients are tuned using the Ziegler-Nichols (Z-N) method and the characteristics of unit step response are analyzed to select the PID coefficients at various pump speeds. Results: Results showed that the performance of the PID controller was superior in any condition. It was found that the highest settling time and maximum overshoot were less than 0.210 s and 5%, respectively at all pump speed. It was determined that the steady state errors were 0% in all the cases. The lowest overshoot and settling time were calculated to be nearly 2.56% and 0.205 s, respectively at the pump rated speed (2650 rpm). Conclusions: The results indicated that the developed PID control algorithm would be feasible for the ascending and descending system of a rice transplanter. Finally, it would be helpful to plant the seedlings uniformly and improve the performance of the rice transplanter.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1365-1372
• /
• 2018

Recently, the aging of agricultural society has caused a rapid increase in safety accidents in -agricultural machinery. Sometimes, the wounded may be left unattended resulting serious situation. In order to solve these problems, ICT technology is used to detect and inform the accident quickly when a safety accident such as overturning, collision or other accidents occurs during the operation or moving the agricultural machinery, such as cultivator, rearing machine, and tractor. A system capable of minimizing the amount of data is required. In this paper, an ICT - based automatic accident detection & propagation system is proposed for the agricultural machinery accident such as colliding crashes or overturning of agricultural machinery. The proposed system enables quick rescue by sending a text message automatically to family, acquaintances, hospitals and 119 in the event of an agricultural accident.

• 연구논문집
• /
• s.29
• /
• pp.185-194
• /
• 1999

The shape and thickness distribution according to the pressure-time curve were carried out using the FEM and experiment. Also, mechanical properties were investigated. The square cup parts have been formed with pressure-time curve generated by result of analysis. The tensile strength and elongation have been investigated according to applied pressure conditions using the tensile test specimen obtained from the superplastic formed cup. We can use to predict the shape of formed part under the applied pressure using the FEM analysis. In the case of optimum pressure condition, the thickness distribution and mechanical properties were improved. From this study, we can find the important of optimum pressure-time condition. We have investigated about the forming of airplane part and fuel tank for motorcycle. If the applied load used in boundary conditions was appropriate, the simulation result coincides with the formed part. However, it is very difficult to define the pressure condition in complicated shape. Thus, it is need to develop the optimum pressure condition for superplastic forming.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.92-97
• /
• 1998

The morpholgies of the wear particles are directly indicative of wear processes occuring in machinery and their severity. The neural network was applied to identify wear debris generated from the machine driving system. The four parameters(50% volumetric diameter, aspect, roundness and reflectivity) of wear debris are used as inputs to the network and learned the friction condition of five values(material 3, applied load 1, sliding distance 1). It is shown that identification results depend on the ranges of these shape parameters learned. The three kinds of the wear debris had a different patter characteristic and recognized the friction condition and materials very well by artificial neural network. We discussed how the network determines differencee in wear debris feature, and this approach can be applied to foreseeability and decisio for moving condition of the Machine driving system.

• 연구논문집
• /
• s.22
• /
• pp.65-74
• /
• 1992

This paper aims at calculating optimum design dimensions to minimize the weight satisfied strain and stress intensity of the frame while loading maximum weight into a mechanical press in the static condition. Analysis of the frame was carried out by using the FEM, then the optimum condition was obtained by using these data. As modeling in the finite element analysis has great impact on the reliablity of analysis results, the analyzed object was selected a 150-ton mechanical press of J Company, the part little affected to structural rigidity was simplified, the load condition was considered in the only maximum load, the boundary condition was used by giving symmetric displacement due to symmetric boundary condition, the finite element was applied a linear membrane element. An intermediate processor program applied the normal ANSYS to analyze finite elements was developed, and the design sensitivity was calculated. This program was applied to the optimum design.

• 한국기계연구소 소보
• /
• s.9
• /
• pp.115-131
• /
• 1982

• 열병합발전
• /
• s.37
• /
• pp.18-21
• /
• 2004

There are several bearing system at large steam-turbines in thermal power plant. The bearing system is one of the most important parts of rotating machinery. The steam turbine vibrations mainly depend on the bearing oil the shaft alignment condition. This paper describes on the steam turbine abnormal vibration due to the oil whip in terms of the shaft alignment in the thermal power plant.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.161-164
• /
• 2002

Present condition of small fan used in appliances and IT industry is briefly reviewed. Here, fans used in refrigerator, air-conditioner, vacuum cleaner, microwave oven and computer are surveyed. Also some comments about the issue of each fan is described.