• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.335-340
• /
• 2009

Ultrashort pulse laser drilling of polycarbonate track-etched membrane (pTEM) material was used to fabricate a mouse embryo cell trapping device. Holes with a diameter of $2{\mu}m$ to $5{\mu}m$ were fabricated on a $10{\mu}m$ thick membrane using a femtosecond laser with a 150 fs pulse width and 775 nm wavelength and multiple-pulse irradiation. In cell trapping tests, the overall cell occupancy of the machined holes in the fabricated pTEM was found to be more than 80%. The results of a single pulse and multiple pulse irradiation were compared in terms of the surface quality. It was generally found that a single pulse with high energy was less desirable than irradiation with multiple pulses of lower energy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.3
• /
• pp.1-6
• /
• 2009

This paper presents a geometrical error compensation of tool alignment for sharp edge bite on B axis controlled machine. In precision micro patterning, bite alignment is crucial parameter for machined surface. To decrease bite alignment error, plus tilted bite from B axis center is touched to reference work piece(pin gauge) and checked the deviation from original position. Same process is repeated for maximum touch deviation value. From this touched position value, wheel alignment error in X axis and Z axis can be calculated on B axis center. Experimental results show that this compensation method is efficient to correct sharp edge bite alignment.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.294-299
• /
• 2005

A machining center is a complex dynamic system whose behavior influences the machining stability and machined surface quality. This paper focused on establishment of a measurement system and experimental study on static, dynamic, and modal analysis of a machining center. The dynamic stiffness result by the analysis showed the weak part of the machining center. The results provided structure modification data for getting better dynamic behaviors.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.123-127
• /
• 1999

This paper suggests the establishment of high-accuracy and high-efficiency machining method of scroll shape workpiece by using the feed control method. The cutting paths for machining the inside and outside surfaces of the scroll-shape workpiece are calculated, and the calculation method of the cutting chip areas based on the coordinate of the base circle is shown. A feed control method is proposed for a constant cutting area and cutting force. By machining test of scroll shape workpiece, The machined accuracy of wrap, tool wear, and surface roughness are evaluated. By this method, Reduction of the machining time and large increase of the efficiency can be expected.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.314-318
• /
• 2002

Several types of burrs form on the edges of all machined and stamped parts. These burrs must be removed to prevent interference fits or short circuits, to improve fatigue life or to prevent injury. Despite the full or partial automation of FMC or FMS, deburring operations to obtain workpiece with fine surface quality are difficult to be automated since the occurrence and condition of burr are not constant. This study focused on developing micro-deburring technique for small electro- parts produced by press process. The successful performance was demonstrated by deburring experiment using the powder blasting.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.4
• /
• pp.1-7
• /
• 2008

Fine grained superplastic Zn-22%Al alloy was extruded using a laser machined micro-die to produce a micro-gear shaft. Extrusion process was conducted under a constant pressure at constant temperatures ranging from 503 to 563K. Laser machining was capable to machine a micro-die with close tolerances and adequate surface quality. The extrusion rate increased with extrusion load under constant extrusion temperature. The rate reached a steady state and became constant after a certain period. There was a small instantaneous stroke on application of the load and then a very brief primary stage which preceded steady-state flow. The micro-extrusion process was proven to produce a micro-gear shaft successfully using a fine grained superplastic Zn-22%Al alloy.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.213-220
• /
• 2003

By the localization of electro-chemical dissolution region, we succeeded in a few micrometer size hole drilling on stainless steel with the radial machining gap of about 1 ${\mu}{\textrm}{m}$. Tens of nanosecond duration voltage pulses were applied between WC micro-shaft and stainless steel in the 0.1 M $H_2SO_4$ solution. Pt balance electrode was used to drill the high aspect ratio micro-hole without generation of Cr oxide layer on the machined surface. The effects of applied voltage, pulse duration, and pulse period on localization distance were investigated according to machining time. We suggested the taper reduction technique especially brought up on blind-hole machining. High quality micro-holes with 8 ${\mu}m$ diameter with 20 ${\mu}m$ depth and 12 ${\mu}m$ diameter with 100 ${\mu}m$ depth were drilled on 304 stainless steel foil. The various hole shapes were also produced including stepped holes and taper free holes.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.3 no.1
• /
• pp.40-48
• /
• 2000

The term "deep holes" is used to describe the machining of holes with a relatively large length to diameter ratio. The main feature of BTA deep hole drilling is the stabilization of cutting force necessary for the self guidance of the drill head. An additional feature is the cutting tool edges that are unsymmetrically placed on the drill head. There is an increasing necessity to predict the hole geometry and other dynamic stability behavior of deep hole drilling guidance. In this study, the effects of BTA deep hole drilling conditions on the hole profile machined piece are analyzed using domain analysis technique. The profile of deep hole drilled work piece is related to cutting speed, feed rate, chip flow, tool wear, and so on. This study deals with the experimental results obtained during the BTA drilling on SM45C, SM55C carbon steels and SCM440 steels under various cutting conditions, and these results are compared with analytical evaluations.aluations.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.83-87
• /
• 2002

Accurate acquisition of surface geometries such as machined surfaces, biological surfaces, and deformed parts and processing 3D object have been very important technique in scientific study and engineering, expecially for system design, manufacturing and inspection. Defective human teeth are usually ground to be coped with special alloy coping which is hand-made by dental technician. This make dental technician to be difficult and take a long time Dental CAD/CAM Systems consist of two parts, data acquisition and milling. In this paper, a method is studied to mill object which is acquired 3D geometric data of the small object such as a die in stone model. This paper present a control program and a mechanical system for milling 3D object.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.3
• /
• pp.120-128
• /
• 2007

In order to reduce the lead-time and cost, the technology of rapid prototyping(RP) has been widely used. This paper describes the methodology to fabricate a large object by using the principle of rapid prototyping. By laminating thick and sloping polystyrene foam plates, we can make the large model which has three dimensional, continuous surfaces faster and easier than conventional processes. Estimated error was much smaller than other RP products which have stepped effect. For accuracy improvement and post processing, machined metal plates are added between the thick plates. To keep the continuity of surface and strengthen the model, pilot holes and guide rods are applied. By the methodology described in this paper, a missile body with flush air intake was fabricated.