• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술대회 논문집 전문대학교육위원
• /
• pp.87-91
• /
• 2003

Most of the loads in industrial power distribution systems are balanced and connected to three wires power systems. However, in the user power distribution systems, most of the loads are single & three phase and unbalanced, generating a large amount of non-characteristic harmonics. With the advent of power electronics and proliferation of non-linear loads in industrial power applications, power harmonics and their effects on power quality are a topic of concern. Harmonics by the unbalance voltage and non-linear loads, cause the increase of machine loss and heating. In order to allow current harmonic compensation, a filter must be installed. This paper describes the performance of passive filter under the voltage unbalance and non-linear load.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1709-1716
• /
• 2003

Stirling engine is a heat engine with a high potential efficiency, multi-fuel capability, its low emission, quiet operation, very low maintenance requirement and long life. The Stirling cycle can ideally achieve optimum thermodynamic efficiency of the Carnot cycle. But the actual efficiency of practical reciprocating Stirling engine is much less than that of ideal Stirling cycle due to several mechanical limits. This paper presents a new-type Stirling engine employing the scroll mechanism superior to the reciprocating Stirling engine. The new-type Stirling engine is characterized as traits of continuous and wholly seperated compression and expansion, one-way flow, direct cooling and heating through the extensive surfaces of scroll wraps. By means of this traits, the new-type Stirling engine can achieve thermodynamic cycle closer to the ideal Stirling cycle and have many mechanical merits. Also, the new-type Stirling cycle can be applied as Stirling refrigerator and Duplex Stirling machine.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.94-100
• /
• 2001

Distortion is a potential problem with all welded fabrication and should be caused dimensional changes and mismatch of joints during welding fabrication. Correction unacceptable weld distortion is extremely costly and in some case impossible. The aim of the present work is to verify the variation of the compressive force, tensile force and distortion during plastic deformation under Tungsten-inert-gas(TIG) welding, on type 304 stainless steel. Experimental results show that possibili-ty if measuring deformation during welding and good correlation was found between analytical and experimental result ad finite element methods have been used to model temperature analysis.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.463-467
• /
• 2004

This paper presents the fabrication possibility of the micro actuator which uses a micro-thermal bubble, generated b micro-heater under pulse heating. The valve-less micropump using the diffuser/nozzle is consists of the lower plate, he middle plate, the upper plate. The lower plate includes the channel and chamber are fabricated on high processability silicon wafer by the DRIE(Deep Reactive Ion Etching) process. The middle plate includes the chamber and diaphragm d the upper plate is the micro-heater. The Micropump is fabricated by bonding process of the three layer. This paper resented the possibility of the PCR chip operation by the fabricated micropump.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권10호
• /
• pp.491-500
• /
• 2003

Most of the loads in industrial power distribution systems are balanced and connected to three wires power systems. However, in the user power distribution systems, most of the loads are single & three phase and unbalanced, generating a large amount of non-characteristic harmonics. With the advent of power electronics and proliferation of non-linear loads in industrial power applications, power harmonics and their effects on power quality are a topic of concern. Harmonics by the unbalance voltage and non-linear loads, cause the increase of machine loss and heating. In order to allow current harmonic compensation, a filter must be installed. This paper describes the performance of passive filter under the voltage unbalance and non-linear load.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2109-2111
• /
• 1998

This paper proposes a new lossless snubber circuit on power supply for welding machine's output rectification diode. To improve the common inverter control type power supplies' problems that energy loss and heating in the snubber circuit because the output capacity makes too big heat energy in the circuit when the output current of the inverter is rectified by the diode bridge circuit, which includes the snubber circuit. This paper suggested new snubber circuit have increased power factor and confidence of output by being regenerate thus lost energy to input node.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.948-951
• /
• 2008

Ubiquitous sensor network (USN) based on ZigBee communication protocol has been used in various application fields, such as home-network, intelligent building and machine, logistics, environmental monitoring, military field, security field and etc. The ZigBee is targeted at radio-frequency application that require a low data rate, long battery life and secure network. Especially, the USN system can be applied efficiently to building-indoor where the complex geometry is adopted. In this study, all 90 points of railway cabin indoor were monitored for temperature and humidity using USN technology. All sensors were pre/post-calibrated and the temperature/humidity change were analyzed in a railway cabin in real-time. The results would be useful to develop the cabin heating, ventilating and air conditing (HVAC) system to meet all passengers' thermal comfort regardless of their seat position.

• 대한가정학회지
• /
• 제20권2호
• /
• pp.65-71
• /
• 1982

Comfort concept of heating and cooling between body and environment is modified by the clothing. So were can say the clothing is one of the environment. To maintain“pleasantness”, clothing must have the elements of comfort and function. This study carried out for the 1st step to describe the relation between clothing and the human body I aspect to the emvironmental elements of temperature and working part of the body. Observations of skin temperature were taken on young adults female subjects in training wear and the skin temperature was measured onto 9 points of the body while taking part in two physical exercise, with Rawing machine and Bicycle ergometer. The results obtained are as follows; 1. The skin temperature after physical exercise is lower than that after repose. 2. After physical exercise of the lower part of the body, the skin temperature is less than that after physical exercise of the upper part of the body. 3. After physical exercise of the upper part of the body, skin temperature of the lower part of the body rises a little, and vice versa.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2458-2460
• /
• 1998

To drive motor or heating machine, it needs the electric power system like the apparatus of inverter. This electric power system obviously comprises power switching devices and drivers to run them. And this system has the topology comprised one/many arm(s), - each arm has high side switching device and low side switching device. Transformer, photocoupler, and HVIC having functions of isolation and level shift which are important thing to drive high side switching device are used as component of drivers in conventional apparatus. Piezoelectric transformers are proposed in this paper, and applied to drive high side swiching device. Through experiments, the possiblities of driving high side switching device are presented and the problems are mooted concurrently. But, we also consider a counterplan for solving the mooted trouble issues.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.63-70
• /
• 2001

This study is concerned with Finite Element Analysis on welded part of control link fur automobile. For analysis, control link was modeled into two parts, ring and rod. Heating condition, temperature distributions and fatigue fracture strength were analyzed using "HEAT III" and "NDURE" module of NISA II. Metal flow in the process of welding was simulat- ed by $DEFORM^{TM}2D$.The analyzed results were compared with experimental inspection. Quality of welded part was able to be improved by controlling metal flow in the process of welding by increase the friction constant of ring part. Heat transfer analysis and flow simulations were in good agreement wish welding experiments.