• The Korean Journal of Ceramics
• /
• v.1 no.3
• /
• pp.125-130
• /
• 1995

Electrical discharge machinable $SiC-TiB_2$ composites were fabricated by hot-pressing. Their mechanical and electrical properties were determined as a function of $TiB_2$ content. The addition of $TiB_2$ to SiC matrix increased the strength and toughness and decreased electrical resistivity. The flexural strength and fracture toughness of SiC-40 vol% $TiB_2$ composited were approximately 50% higher than those of monolithic SiC ceramics. Microstructural analysis showed that the toughening was mainly due to the crack deflection, with some possible contribution from crack branching or microcracking.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.291-295
• /
• 2002

Ceramics are very difficult-to-cut materials because of its high strength and hardness. Their machining process can be characterized by cracking and brittle fracture. Generally, ceramics are machined using traditional method such as grinding and polishing. However, such processes are generally costly and have low material removal rate. In this paper, to develop machinable ceramics those have good machinability without losing their material properties, machinability evaluations are performed by applying the experimental design method. In this paper, to evaluate the machinability of the developed ceramics, various workpieces are machined on the CNC machining center, and surface roughness are measured under predefined process parameters obtained using Taguchi method. And the experimental results are investigated to derive optimum cutting parameters for the given materials.

• The Korean Journal of Ceramics
• /
• v.1 no.2
• /
• pp.101-105
• /
• 1995

Electrical discharge machinable $Si_3N_4$ was fabricated with the addtion of 20-60 vol% TiN by gas pressure sintering. Their sinterability, microstructure, mechanical and electrical properties were characterized as a function of the TiN content. The addition of TiN up to 20 vol% increased the flexural strength and fracture toughness as compared with those of the monolithic Si3N4. For the TiN content higher than 40 vol%, the electrical resistivity was lower than $1062\Omega$.cm. The $Si_3N_4$ with the addition of 40 vol% of TiN appears to have the optimum considerable sinterability, mechanical and electrical properties, and machinability. A microstructural analysis showed that the enhanced toughening was due to the crack deflection.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.372-377
• /
• 2013

Machinable SiC ceramics are prepared with the addition of $Al_2TiO_5$. Ready-to-press SiC and $Al_2TiO_5$ powders are mixed and pressureless sintered at $1750^{\circ}C$ and $1850^{\circ}C$ for 1 h. The weight ratios of the SiC and $Al_2TiO_5$ powders are 100 : 0, 100 : 10, and 100 : 20. After sintering, only SiC peaks are detected in the X-ray diffraction analyses. The density, strength, and grain size of the SiC increase with increases in the $Al_2TiO_5$ content and sintering temperature. The $Al_2TiO_5$-doped specimens are easy to micro-hole machine. Based on the density and strength data, the ceramics sintered at $1850^{\circ}C$ can be used as machinable ceramics.

• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.390-401
• /
• 2008

The objective of this study is to evaluate various machining characteristics of AlN-hBN machinable ceramics in micro end-milling process for its further application. First, AlN based machinable ceramics with hBN contents in the range of 10 to 20vol% were prepared by hot-pressing. Material properties of the composites, such as relative density, Vickers hardness, flexural strength, Young's modulus and fracture toughness were measured and compared. Then, micro end-milling experiments were performed to fabricate micro channels using prepared system. During the process, cutting forces, vibrations and AE signals were measured and analyzed using applied sensor system. Machined micro channel shapes and surface roughness were measured using 3D non-contact type surface profiler. From the experimental results, it can be observed that the cutting forces, vibrations and AE signal amplitudes decreased with increasing hBN contents. Also, measured surface roughness and profiles were improved with increasing hBN contents. As a result of this study, optimum machining conditions can be determined to fabricate desired products with AlN-hBN machinable ceramics based on the experimental results of this research.

• Journal of the Korean Ceramic Society
• /
• v.28 no.10
• /
• pp.793-802
• /
• 1991

The multicrystalline machinable ceramics was fabricated by melting method using domestic pyrophyllite. After determination of optimum crystallization temperature and time from results of DTA, XRD and SEM, base glasses were heat treated by 2-step schedule. Main crystalline phases identified by XRD, EDX were Na-fluorophlogopite, ${\beta}$-spoduemen and ${\alpha}$-cordierite, and the crystallization condition of these crystals was varied with chemical composition, thermal history and nucleation agents. The thermal, chemical properties of prepared samples were excellent.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.181-182
• /
• 2009

• Journal of the Korean Society of Safety
• /
• v.25 no.5
• /
• pp.1-6
• /
• 2010

When the ceramic material is being machined, micro crack and brittle fracture dominate the process of material removal. Generally, ceramics are very difficult-to-cut materials and machined using conventional method such as grinding and polishing. However, such processes are generally cost-expensive and have low material removal rate. Machinable ceramics used in this study contain BN powder to overcome these problem and for productivity elevation. This paper focuses on machinability evaluation during end mill process with CNC machining center in this study. Experiment for this purpose is performed for tool wear patterns and mechanism.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.581-585
• /
• 2012

Machinability is important in engineering applications, especially in the current micro-electronics industry. Most ceramic components have complex shapes and hence require machining generally with diamond tools, which incurs a high production cost. Recently, h-BN-containing machinable ceramics have been developed, but these materials are very expensive due to the high raw materials and production costs. Therefore, the development of low-cost machinable ceramics is necessary. In this study, inexpensive $Al_2TiO_5$ was studied as a replacement for h-BN. $Al_2O_3$, $TiO_2$ and partially stabilized $ZrO_2$(PSZ) powders were mixed with various mole ratios and were sintered at $1500^{\circ}C$ for 1 h. The density, hardness and strength were then measured. The phase analysis and microstructures were observed by XRD and SEM, respectively. The machinability of each specimen was tested by micro-hole machining. The results of this research showed that the produced composites could be used as low-cost machinable ceramics.

• Journal of the Korean Ceramic Society
• /
• v.28 no.7
• /
• pp.531-540
• /
• 1991

In this study, high quality machinable ceramics was prepared from the K2O-MgO-Al2O3-SiO2-B2O3-F glass system using domestic pyrophyllite. The mixture of pyrophyllite and additives was melted at 1450$^{\circ}C$ for 1 hour and formed in a graphite mold. The base glass was heat-treated at 600$^{\circ}C$ to 1200$^{\circ}C$ with interval of 50$^{\circ}C$ for 3 hours identified by XRD. Crystalline phase were confirmed by XRD and their microstructure was observed by SEM. The glass ceramics which was prepared by heat treatment of base glass at 1150$^{\circ}C$ for short time has good physical, mechanical, thermal, chemical properties and machinability.