• Composites Research
• /
• v.17 no.2
• /
• pp.28-33
• /
• 2004

Failure detection in a cross-ply laminated composite beam under tensile loading were performed using a fiber Bragg grating (FBG) sensor. A Passive Mach-Zehnder interferometric demodulator was proposed to enhance sensitivity and bandwidth. The proposed FBG sensor system without active device such as a phase modulator is very simple in configuration, easy to implement and enables the measurement of high-frequency vibration with low strain amplitude such as impact or failure signal. Failure signals detected by a FBG sensor had offset value corresponding to the strain shift with vibration at a maximum frequency of several hundreds of kilohertz. at the instant of transverse crack propagation in the 90 degree layer of composite beam.

• Korean Journal of Optics and Photonics
• /
• v.1 no.2
• /
• pp.125-129
• /
• 1990

One method for time-division multiplexing (TDM) of Michelson type fiber-optic interferometric sensor arrays is proposed and demonstrated experimentally. This method has some advantages; fewer fiber-optic components. low cost. and high reliability.bility.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.474-479
• /
• 1993

An interferometric fiber-optic magnetic field sensor is constructed by bonding a Co-Fe-B metallic glass transducer developed here by the melt-spun method to a single mode fiber arm in the fiber Mach-Zehnder interferometer and is tested. The bias field for the peak ac-sensitivity was observed near 0.97 Oe and the minimum detectable magnetic field was 3.9${\times}10^{-5}$ Oe(rms)/${\sqrt{Hz}}$ a 3 kHz. The output of the ac field sensor becomes saturated near the input signal level of 1 Oe(rms). The Co- Fe-B transducer exhibits peak response near 500 Hz.

• Journal of the Optical Society of Korea
• /
• v.3 no.2
• /
• pp.64-68
• /
• 1999

The performance of a fiber Bragg grating strain sensor constructed with 3$\times$3 coupler is investigated. A 3$\times$3 coupler Mach-Zehnder (M/Z) interferometer is used as wavelength discriminator, interrogating strain-induced Bragg wavelength shifts. Two quadrature-phase-shifted intensities are synthesized from the as-coupled interferometer outputs, and digital arctangent demodulation and phase unwrapping algorithm are applied to extract the phase information proportional to strain. Due to the linear relation between the input strain and the output of quadrature signal processing, signal-fading problems eliminated. In the experiment, a fiber grating that was surface adhered on an aluminum beam was strained in different ways, and the photodetector signals were transferred and processed in a computer-controlled processing unit. A phase recovery fo 7.8$\pi$ pk-pk excursion, which corresponds to ~650$\mu$strain pk-pk of applied strain, was demonstrated. The sensor system was stable over the environmental intensi쇼 perturbations because of the self-referencing effect in the demodulation process.

• Journal of Sensor Science and Technology
• /
• v.10 no.4
• /
• pp.214-221
• /
• 2001

The use of an asymmetric Mach-Zehnder interferometric amplitude modulator to measure a relatively low frequency electric field strength is described. The sensitivity of an electric field sensor using a $Ti:LiMbO_3$ optical modulator is strongly affected by the shape of a electrode(probe antenna). To measure the low frequency electric field, a probe antenna of wide effective area is more useful than the usual dipole antenna. As a proof of this, the optical modulator was fabricated with a plate-type probe antenna and the usefulness of this antenna tested for measuring low frequency electric field strength. Measurements were performed in the range 0.1 V/cm to 60 V/cm at 60Hz through 100 kHz. Using a probe antenna of $10\;mm{\times}10\;mm$, the output voltage of $10^{-2}\;mV$ was measured with respect to the electric field strength of 0.1 V/cm at 60 Hz. By increasing the effective area of the probe antenna, better sensitivity is obtainable over the measured range.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.6
• /
• pp.1-7
• /
• 2002

The use of an asymmetric Mach-Zehnder interferometric amplitude modulator to measure a relatively low frequency electric field strength is described. The sensitivity of an electric field sensor using a Ti:LiNbO$_3$ optical modulator is strongly affected by the shape of a electrode(probe antenna). To measure the low frequency electric field, a probe antenna of wide effective area is more useful than the usual dipole antenna. As a proof of this, the optical modulator was fabricated with a plate-type probe antenna and the usefulness of this antenna tested for measuring low frequency electric field strength. Measurements were performed in the range 0.1V/cm to 60V/cm at 60Hz through 100KHz. Using a probe antenna of 10mm$\times$10mm, the output voltage of 10㎷ was measured with respect to the electric field strength of 0.1V/cm at 60Hz. By increasing the effective area of the probe antenna, better sensitivity is obtainable over the measured range.