• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.813-820
• /
• 2005

In this study, finite element modeling and structural vibration analyses of a gyrocopter have been conducted considering dynamic hub-loads due to rotating blades. For this research, 3D CATIA models for most mechanical parts are exactly prepared and assembled into the final aircraft configuration. Then the dynamic finite element model including several non-structural parts are constructed based on the exact 3D CAD data. Computational structural dynamics technique based on finite element method is applied using both MSC/NASTRAN and developed in-house code which can largely reduce the pre and postprocessing time of general transient dynamic analyses. Modal based transient and frequency response analyses are used to efficiently investigate vibration characteristics. The results include natural frequency comparison for different fuel and pilot conditions, fundamental natural mode shapes, frequency responses and transient acceleration responses of the present gyrocopter model.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.63-71
• /
• 2005

In this study, structural vibration analyses of a composite smart unmanned aerial vehicle (UAV) have been conducted considering dynamic hub-loads of tilt-rotor. Practical computational structural dynamics technique based on the finite element method is applied using MSC/NASTRAN. The present smart UAV(TR-S2) structural model is constructed as full 3D configurations with both the helicopter flight mode and the airplane flight mode. Modal based transient response and frequency response analyses are used to efficiently investigate vibration characteristics of structure and installed electronic equipments. It is typically shown that the helicopter flight mode with the 90-deg tilting angle is the most critical case for the induced vibration of installed electronic equipments in the front.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.112-119
• /
• 2004

This paper develops a computer model of a cabover type large truck for estimating the effects of the mounted method of frame on handling performance. The computer model considers two mounted methods of frame; flange mounted and web mounted. Frame is modeled by finite elements using MSC/NASTRAN in order to consider the flexibility of frame. The reliability of the developed computer model is verified by comparing the actual vehicle test results with the simulation results. The actual vehicle test is performed in a double lane change course, and lateral acceleration, yaw rate, and roll angle are measured. To estimate the effects of the mounted method of frame on handling performance, simulations are performed with the flange mounted and web mounted frame. Simulation results show that the web mounted frame＇s variations of roll angle, lateral acceleration, and yaw rate are larger than the flange mounted frame＇s variations, especially in the high test velocity and the second part of the double lane course. Also, simulation results show that the web mounted frame＇s tendencies of roll angle, lateral acceleration, and yaw rate advance the flange mounted frame＇s tendencies, especially in the high test velocity and the second part of the double lane course.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.690-693
• /
• 2005

In this paper, probabilistic distribution of fatigue life of chassis component is determined statistically by applying the design of experiments and the Pearson system. To construct $p-\varepsilon-N$ curve, the case that fatigue data are random variables is attempted. Probabilistic density function(p.d.f) for fatigue life is obtained by design of experiment and using this p.d.f fatigue reliability about any aimed fatigue life can be calculated. Lower control arm and rear torsion bar of chassis component are selected as examples for analysis. Component load histories, which are obtained by multi-body dynamic simulation for Belsian load history, are used. Finite element analysis are performed using commercial software MSC Nastran and fatigue analysis are performed using FE Fatigue. When strain-life curve itself is random variable, probability density function of fatigue life has very little difference from log-normal distribution. And the case of fatigue data are random variables, probability density functions are approximated to Beta distribution. Each p.d.f is verified by Monte-Carlo simulation.

• 한국군사과학기술학회지
• /
• 제12권6호
• /
• pp.704-710
• /
• 2009

In this study, a comparison study of flutter analysis for the AGARD 445.6 wing with wind turnnel test data has been conducted in the subsonic, transonic and supersonic flow regions. Nonlinear aeroelastic using FSIPRO3D which is a generalized user-friendly fluid-structure analyses have been conducted for a 3D wing configuration considering shockwave and turbulent viscosity effects. The developed fluid-structure coupled analysis system is applied for aeroelastic computations combining computational structure dynamics(CSD), finite element method(FEM) and computations fluid dynamics(CFD) in the time domain. MSC/NASTRAN is used for the vibration analysis of a wing model, and then the result is applied to the FSIPRO3D module. the results for dynamic aeroelastic response using different turbulent models are presented for several Mach numbers. Calculated flutter boundary are compared with the wind-tunnel experimental and the results show very good agreements.

• Composites Research
• /
• 제14권6호
• /
• pp.9-15
• /
• 2001

본 연구에서는 복합재료로 만들어진 박판의 상자형 보에 대만 선형 정적해석을 수행하였다. 복합재료 보의 해석을 위해서 혼합 보 이론을 적용하였으며, 상자형 단면의 벽에 대해 설정이 가능한 여러 가지 구성방정식을 고려할 수 있도록 하였다. 굽힘-비틀림 혹은 인장-비틀림 연성을 갖는 단순한 적층 형상의 복합재료 강자형 보를 예로 들어 보의 정적 거동에 미치는 복합재료의 연성효과를 고찰하였다. 본 해석결과의 타당성을 검증하기 위만 방편으로 상용 구조해석 프로그램을 이용한 정밀 유한요소 구조해석을 수행하였다. 혼합 보 이론을 이용하여 복합재료 상자형 보에 대한 단면상수 등을 해석적으로 결정하였으며, 적절한 구성방정식의 설정 여부가 최종적인 해의 정확도를 결정하는 중요한 요소임을 보였다.

• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.731-737
• /
• 2005

This paper evaluates dynamic performance of a cab over type large-sized truck for estimating the effects of frame's torsional characteristics using a computer model. The computer model considers two mounting methods of frame, flange mounting and web mounting. Frame is modeled by finite elements using MSC/NASTRAN In order to consider the flexibility of frame. The torsional test of the frame is conducted In order to validate the modeled finite element model. A load cell is used to measure the load applied to the frame. An angle sensor is used to measure the torsional angle. An actuator is used to apply a load to the frame. To estimate the effects of frame's torsional characteristics on dynamic performance, simulations are performed with the flange mounting and web mounting frame. Simulation results show that the web mounting frame's variations of roll angle, lateral acceleration, and yaw rate are larger than the flange mounting frame's variations, especially in the high velocity and the second part of the double lane course.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.84-91
• /
• 2011

A finite element analysis for the wing and landing gear of a composite target-drone air vehicle was performed. For the wing analysis, two load cases were considered: a 5g symmetric pull-up and a -1.5g symmetric push-over. For the landing gear analysis, a sinking velocity of 1.4 m/s at a 2g level landing condition was taken into account. MSC/NASTRAN and LS-DYNA were utilized for the static and dynamic analyses, respectively. Finite element results were verified by the static test of a prototype wing under a 6g symmetric pull-up condition. The test showed a 17% larger wing tip deflection than the finite element analysis. This difference is believed to come from the material and geometrical imperfections incurred during the manufacturing process.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권1호
• /
• pp.70-81
• /
• 2017

Various components of an engine nozzle are modeled as flexible multi-body components that are operated under high temperature and pressure. In this paper, in order to predict complex behavior of an engine nozzle, thermo-fluid-flexible multi-body dynamics coupled analysis framework was developed. Temperature and pressure on the nozzle wall were obtained by the steady-state flow analysis for a two-dimensional nozzle. The pressure and temperature-dependent material properties were delivered to the flexible multi-body dynamics analysis. Then the deflection and strain distribution for a nozzle configuration was obtained. Heat conduction and thermal analyses were done using MSC.NASTRAN. The present framework was validated for a simple nozzle configuration by using a one-way coupled analysis. A two-way coupled analysis was also performed for the simple nozzle with an arbitrary joint clearance, and an asymmetric flow was observed. Finally, the total strain result for a realistic nozzle configuration was obtained using the one-way and two-way coupled analyses.

• 한국해양공학회지
• /
• 제24권1호
• /
• pp.20-33
• /
• 2010

The paper deals with strength design of a riser support installed on floating production storage and offloading (FPSO) vessel under various loading conditions - operation, extreme, damaged, one line failure case (OLFC) and installation. The design problem is formulated such that thickness sizing variables are determined by minimizing the weight of a riser support structure subject to stresses constraints. The initial design model is generated based on an actual FPSO riser support specification. The finite element analysis (FEA) is conducted using MSC/NASTRAN, and optimal solutions are obtained via moving least squares method (MLSM) in the context of response surface based approximate optimization. For the meta-modeling of inequality constraint functions of stresses, a constraint-feasible moving least squares method (CF-MLSM) is used in the present study. The method of CF-MLSM, compared to a conventional MLSM, has been shown to ensure the constraint feasibility in a case where the approximate optimization process is employed. The optimization results present improved design performances under various riser operating conditions.