• Progress in Superconductivity and Cryogenics
• /
• v.8 no.1
• /
• pp.23-25
• /
• 2006

Optimization of process variables, including oxygen and water partial pressure and also an nesting temperature, was performed in batch-type process to fabricate YBCO films on LaAlO3 single crystal. In this work, YBCO oxide powder was used as a starting precursor for metal-organic deposition(MOD)method. The precursor films were fabricated in batch furnace and they were converted to the epitaxial YBCO films at the same furnace with varying the process variables. The oxygen partial pressure was varied from 100ppm to 2000ppm and the water partial pressure from 1.2% to 12.2%. The window for optimal P(O2) was narrow about 700ppm for batch-type process. YBCO films in bathc-thype MOD process were optimized at 740-770oC and P(H2O) of 2.3%-7.3%.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.91-95
• /
• 2007

[ $YBa_2Cu_3O_{7-{\delta}}$ ] films have been prepared on $LaAlO_3$ (100) single-crystal substrates by the metal organic deposition using dichloroacetate precursors (DCA-MOD). DCA precursor solutions with different composition such as; Yttrium-excess(15 at%), barium-poor(25 at%), and a stoichiometric(Y:Ba:Cu=1:2:3) were prepared in order to investigate the effects of precursor composition on the properties of YBCO films prepared by DCA-MOD method. Coated films were calcined at low temperature up to $500^{\circ}C$ in flowing humid oxygen atmosphere. Conversion heat treatment was performed $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. For the film prepared using excess yttrium composition, high critical current density ($J_c$) of $>2MA/cm^2$ was obtained whereas, for the films prepared using barium-poor composition, $J_c$ was lower than $1MA/cm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.33-34
• /
• 2006

The effects of Ba and Ce addition has been investigated in YBCO prepared by trifluoroacetate (TFA) metalorganic depostition (MOD) method. Precursor solutions with cation ratios of Y:Ba:Cu:Ce = 1:2+x:3:x (x = 0, 0.05, 0.1 and 1.5) have been prepared by adding an excess amount of cerium and barium. Coated film was calcined at lower temperature and conversion heat treatment at temperature of $780{\sim}810^{\circ}C$. It has been shown that the critical current (Ic) of YBCO film was degraded by doping of Ba and Ce atoms. But Ic was increased as the amount of doped Ba and Ce content increased from 5 % to 15 %. It was observed that there was little increase of a flux pinning force with Ba and Ce addition in YBCO film prepared by TFA-MOD process.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.103-109
• /
• 2013

Miller-Rabin method is the most prevalently used primality test. However, this method mistakenly reports a Carmichael number or semi-prime number as prime (strong lier) although they are composite numbers. To eradicate this problem, it selects k number of m, whose value satisfies the following : m=[2,n-1], (m,n)=1. The Miller-Rabin method determines that a given number is prime, given that after the computation of $n-1=2^sd$, $0{\leq}r{\leq}s-1$, the outcome satisfies $m^d{\equiv}1$(mod n) or $m^{2^rd}{\equiv}-1$(mod n). This paper proposes a step-by-step primality testing algorithm that restricts m=2, hence achieving 98.8% probability. The proposed method, as a first step, rejects composite numbers that do not satisfy the equation, $n=6k{\pm}1$, $n_1{\neq}5$. Next, it determines prime by computing $2^{2^{s-1}d}{\equiv}{\beta}_{s-1}$(mod n) and $2^d{\equiv}{\beta}_0$(mod n). In the third step, it tests ${\beta}_r{\equiv}-1$ in the range of $1{\leq}r{\leq}s-2$ for ${\beta}_0$ > 1. In the case of ${\beta}_0$ = 1, it retests m=3,5,7,11,13,17 sequentially. When applied to n=[101,1000], the proposed algorithm determined 96.55% of prime in the initial stage. The remaining 3% was performed for ${\beta}_0$ >1 and 0.55% for ${\beta}_0$ = 1.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2000.10a
• /
• pp.275-278
• /
• 2000

This paper focuses on a performance analysis model for optimizing the freight terminal design and layout using AutoMod simulator and numerical analysis. We developed a model to analyze the freiht terminal performance per unit time and the material handling cost based on both throughput and waiting due to conjestion. We developed computer program for this model and some sample results by both numerical method and AutoMod simulator are compared.

• Korean Journal of Optics and Photonics
• /
• v.9 no.5
• /
• pp.333-341
• /
• 1998

The novel integrated device, 1.55 ${\mu}{\textrm}{m}$ DR-LD(distrbuted reflector laser diode) integrated EA-MOD (electro-absorption modulator) as light source, is proposed to improve the device yield and its operational performances. This device can be easily fabricated by the selective MOVPE technique and its fabrication processes are almost the same as the reported 1.55 ${\mu}{\textrm}{m}$ DFB-LD(distributed feedback laser diode) integrated EA-MOD except the asymmetric gratings. The static and dynamic properties are investigated simultaneously by solving the transfer matrix method for light propagation, the time-dependent rate equation for carrier change and schr$\"{o}$dinger equation for QCSE (Quantum-Confined Stark Effect). The performances of the proposed device such as output power, chirp, and extinction ratio are compared with those of DFB-LD integrated EA-MOD. Under 10Gb/s NRZ modulation, we obtain that DR-LD integrated EA-MOD. is 30% higher in output power on the on-state, about 50% lower in chirp, and slightly larger in extinction ratio than DFB-LD integrated EA-MOD.-MOD.

• Journal of Korea Water Resources Association
• /
• v.38 no.3 s.152
• /
• pp.245-257
• /
• 2005

The purpose of the present study is examining the changes of runoff characteristics and extracting hydrologic parameters by applying ModClark model on grid divided watershed. Bocheong stream basin in Geum River system, one of the representative watersheds of IHP projects, is selected. Hydrology-based topographical informations are calculated using GIS data in the HEC-GeoHMS V1.1 extension in Arcview 3.2. The ModClark model requires precipitation data in a gridded format. The gridded data must be recorded in the HEC Data Storage System file format. Therefore, kriging method was used to interpolate the point values to create a grid that gives each cell over the entire watershed a precipitation value. Hec-DSSVue program was used to create DSS file for the rain gage data. The completed HEC-HMS model was calibrated for use in simulating three measured storm events and cell size of 10000m, 5000m, 2000m, 1000m was chosen for the application. As the result of applying distributed rainfall-runoff model to analyze relatively good agreement for peak discharge, runoff volume and peak time.

• Bulletin of the Korean Mathematical Society
• /
• v.53 no.1
• /
• pp.1-20
• /
• 2016

The general number field sieve (GNFS) is asymptotically the fastest known factoring algorithm. One of the most important steps of GNFS is to select a good polynomial pair. A standard way of polynomial selection (being used in factoring RSA challenge numbers) is to select a nonlinear polynomial for algebraic sieving and a linear polynomial for rational sieving. There is another method called a nonlinear method which selects two polynomials of the same degree greater than one. In this paper, we generalize Montgomery's method [12] using geometric progression (GP) (mod N) to construct a pair of nonlinear polynomials. We also introduce GP of length d + k with $1{\leq}k{\leq}d-1$ and show that we can construct polynomials of degree d having common root (mod N), where the number of such polynomials and the size of the coefficients can be precisely determined.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.103-110
• /
• 2010

In this study, an assessment method on creep-fatigue crack initiation and crack growth for a Mod.9Cr-1Mo steel (ASME Grade 91) structure has been developed with an extension of the French RCC-MR A16 procedure. The current A16 guide provides defect assessment procedure for a creep-fatigue crack initiation and crack growth for an austenitic stainless steel, but no guideline is available yet for a Mod.9Cr-1Mo steel which is now widely being adopted for structural materials of future nuclear reactor system as well as ultra super critical (USC) thermal plant. In the present study an assessment method on creep-fatigue crack initiation and crack growth is provided for the FMS (Ferritic-Martensitic Steel) and assessment on the creep-fatigue crack behavior for a structure has been carried out. The assessment results were compared with the observed images from a structural test.

• Journal of Wetlands Research
• /
• v.12 no.1
• /
• pp.51-61
• /
• 2010

Changes in climate have largely increased concentrated heavy rainfall, which in turn is causing enormous damages to humans and properties. Therefore, it is important to understand the spatial-temporal features of rainfall. In this study, RADAR rainfall was used to calculate gridded areal rainfall which reflects the spatial-temporal variability. In addition, Kalman-filter method, a stochastical technique, was used to combine ground rainfall network with RADAR rainfall network to calculate areal rainfall. Thiessen polygon method, Inverse distance weighting method, and Kriging method were used for calculating areal rainfall, and the calculated data was compared with adjusted areal RADAR rainfall measured using the Kalman-filter method. The result showed that RADAR rainfall adjusted with Kalman-filter method well-reproduced the distribution of raw RADAR rainfall which has a similar spatial distribution as the actual rainfall distribution. The adjusted RADAR rainfall also showed a similar rainfall volume as the volume shown in rain gauge data. Anseong-Cheon basin was used as a study area and the RADAR rainfall adjusted with Kalman-filter method was applied in $Vflo^{TM}$ model, a physical-based distributed model, and ModClark model, a semi-distributed model. As a result, $Vflo^{TM}$ model simulated peak time and peak value similar to that of observed hydrograph. ModClark model showed good results for total runoff volume. However, for verifying the parameter, $Vflo^{TM}$ model showed better reproduction of observed hydrograph than ModClark model. These results confirmed that flood runoff simulation is applicable in domestic settings(in South Korea) if highly accurate areal rainfall is calculated by combining gauge rainfall and RADAR rainfall data and the simulation is performed in link to the distributed hydrological model.