• 전기학회논문지
• /
• 제57권10호
• /
• pp.1790-1795
• /
• 2008

Energy scavenging is a technique that converts ambient energy, for example, vibration and light, to electrical energy in order to supply power to low power electronic devices such as ubiquitous sensors. In this paper, we propose an optimal operation condition of power delivery circuit and design strategy for energy scavenging system in which the generated power is order of microwatt and, consequently, efficient handling of power is critical. We also propose that high data transmission rate is more realistic optimal design objective rather than high energy efficiency. It is shown that disconnection of load from the storage capacitor right after data transmission reduces energy wasting and that optimal value of storage capacitor can be determined at this condition. The feasibility of our propose is proved by experiments and we believe that the proposed design strategy will promote the application of piezoelectric micropower generator to the ubiquitous sensor networks.

• 펄프종이기술
• /
• 제38권1호통권113호
• /
• pp.21-26
• /
• 2006

A simple method of on-line stiffness measurement using the wrinkling behavior of paper web between rollers was developed. The theory and calculating equation were presented, and the theoretical maximum error associated with the equation was also presented. We called the stiffness measured by Taber tester as 'Taber stiffness', and by wrinkling behavior as 'wrinkle stiffness', respectively, for comparison. By using this method, on-line complete control of paper stiffness will be possible in near future. Special care about shear wrinkle and paper dimensional effects were addressed.

• 한국인쇄학회지
• /
• 제21권1호
• /
• pp.71-80
• /
• 2003

Printing inks are mainly composed of pigment and vehicles. Among these components, the Vehicle affect the rheologic property of the ink the most but pigment content or characteristic also affect to the fluidity property not less than the vehicle. In the study, with the same vehicle on each sample, by making the sample to increase pigment content gradually. It can be examined the influence of the pigment to the fluidity of ink. In result we found that the viscosity value of the low shear rate rang has relatively higher value with increasing the pigment content in the ink. According to higher pigment content, yield stress and thixotropy index increases gradually. Structure recovery of the ink is that, the higher pigment content's ink, the less changing shear rate, and it takes less time to recover.

• Elastomers and Composites
• /
• 제24권3호
• /
• pp.193-202
• /
• 1989

An experimental study of the development of carbon black dispersion by an internal mixer and its characterization is presented. We describe the measurement of carbon black agglomerate size and related characteristics using four different experimental techniques : optical microscopy, scanning elctrion microscopy, surface roughness, and electrical couductivity. The results from these different experiments are compared uning the same carbon black for a series of six different butadiene-styrene copolymers. The results from the different techniques are cross plotted and are critically discussed. It is found that surface but then sharply deteriorate. At subsequent stages of mixing optical microscopy seemed the most reliable measure.

• 한국태양에너지학회 논문집
• /
• 제21권2호
• /
• pp.9-17
• /
• 2001

In this paper the attempts made by the authors to explore the feasibility of utilising concentrated solar beam radiation for joining engineering thermoplastics such as Acrylonitrilc/Butadiene/Styrene (ABS), Polycarbonate(PC) and Polymethylmethacrylate(PMMA) are presented. In addition, to study the joining of the materials, necessary experimentation with applying primer was performed. Tensile tests were conducted to determine the bond strength achieved at the specimen joint interface. Microscopic examinations of the fractured joints were performed in order to analyse the overall bond quality. Finally, the results in terms of bond strength achieved at the joint interface and energy consumed in the process were compared with those obtained with similar thermoplastic joining technique utilising microwave energy. In conclusion some advantages and limitations were outlined and necessary improvements of the jointing technique were recommended.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.295-300
• /
• 2002

In this paper, an intelligent system to determine welding parameters for each pass and welding position in pipeline welding based on one database and FEM model, two BP neural network models and a C-NN model was developed and validated. The preliminary test of the system has indicated that the developed system could determine welding parameters for pipeline welding quickly, from which good weldments can be produced without experienced welding personnel. Experiments using the predicted welding parameters from the developed system proved the feasibility of interface standards and intelligent control technology to increase productivity, improve quality, and reduce the cost of system integration.

• 한국정보처리학회논문지
• /
• 제5권7호
• /
• pp.1896-1907
• /
• 1998

확장된 마크흐름선도(EMFG: Extednded Mark Flow Graph)는 기존의 MFG를 개선한 그래프로서, 회로변수식에 의해 실제회로로 쉽게 구현가능하므로 이산제어시스템의 모델링과 설계 및 구현의 강력한 도구로 사용될 수 있다. 본 논문은 EMFG의 트랜지션들이 점화하는 과정 및 트랜지션들이 점화완료하였을 때 각 박스들의 마크수 변화를 부울함수식과 벡터를 사용하여 표현하였다. 또한 시스템의 상태변화를 쉽게 판단할 수 있게 하는 EMFG의 동작알고리듬을 제안하였으며, 제안된 알고리듬은 3-비트 증가계수기를 설계한 EMFG와 시간트랜지션이 포함된 가상의 EMFG에서 잘 수행되었다. EMFG의 동작이 부울함수로 해석가능해짐으로 인해 시스템의 분석 및 설계가 용이하며 컴퓨터를 이용한 자동화된 시스템의 분석과 설계가 가능하다.

• 대한치과의사협회지
• /
• 제23권7호통권194호
• /
• pp.577-583
• /
• 1985

The purpose of this investigation was to evaluate scanning electron micrographs of repeatedly cast base metal alloy. For this study two Ni-Cr-Be alloys were used; Rexillium III and Verabond. They were repeatedly cast without addition o new alloy melting with an electric resistant furnace (Castron 8, Yoshida dental equipment Mfg.Co.). They were etched with 10% H₂SO₄ Sol. at 300mA/㎠ for 3 minutes with the use of metal etching unit Oxyetch (OXY dental product Inc.), and ultrasonic cleaning in 18% HC1 Sol. was done. Etched surfaces were examined under a SEM at x 200 and x 750. The surfaces are shown in legends.

• 펄프종이기술
• /
• 제38권3호
• /
• pp.79-84
• /
• 2006

Hydrogen peroxide has been a bleaching chemical for varied pulp, especially mechanical and deinking pulp. It is catalytically decomposed by some transition metals in pulp slurry. In this paper, some metals which can be contained in pulp such as manganese, copper, iron, magnesium and calcium were used to investigate their effect on the decomposition of hydrogen peroxide. From the result, hydrogen peroxide was more decomposed in the order of Mn, Cu, $Fe^{3+}\;and\;Fe^{2+}$, while Mg and Ca had little effect on the decomposition of hydrogen peroxide. The effect of Mg/Mn ratio on the decomposition of hydrogen peroxide was also investigated. At the specific ratio of them(Mg/Mn=10), hindering effect of peroxide decomposition by Mg was decreased.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.115-122
• /
• 1998

The effect of sintering conditions on the sinterability for silicon nitride has been studied by many in-vestigators. However the effect of sintering conditions on the machinability which is the major barrier to the field applications of the ceramic components has not been fully studied. In this study the sintering con-ditions such as temperature gas pressure and time in silicon nitride were varied. The physical and mechan-ical properties of the gas pressure sintered (GPS) silicon nitride were measured. The optimum mi-crostructure of silicon nitride with the excellent machinability was investigated by MFG(magnetic-fluid grinding) technique. An attempt was made to figure out how the mechanical properties influence upon the machinability of silicon nitride ball.