• Food Science of Animal Resources
• /
• v.29 no.4
• /
• pp.482-486
• /
• 2009

The aim of this study was to optimize a simple, fast, and economical analysis procedure for the determination of 16 different pesticides in raw milk via GC/MSD. Analyses were performed via gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC/MSD-SIM) using Pentachloronitrobenzene as the internal standard. The modified sample preparation methodology was based on the Pesticide Analytical Manual (PAM) of the FDA concerning fat extraction, ACN-ether partitioning, and clean-up of the Sep-Pak florisil cartridge. The modified methodology for the determination of the 16 pesticides was validated. The range of LOQs of the 16 pesticides was likely three times lower than their Maximum Residence Levels (MRLs). The recoveries of most of the pesticides were acceptable at the fortification levels of 0.5 and 1.0 ${\mu}g/mL$ and their RSD (%) level was less than 20%. None of the 16 pesticides were detected in the selected raw milk samples.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1240-1243
• /
• 2005

The wrinkling in the flange and wall of a part is a predominant failure mode in stamping of sheet metal parts. In many cases this wrinkling may be eliminated by appropriate control of the blank holding force(BHF), but BHF affects the draw depth. Gotoh had studied the wrinkles under $20{\mu}$ in height. In general, the height of wrinkles could be limited under $200{\mu}$ practically. Therefore small BHF can be allowed so that the depth of drawing could be increased. This paper represents the variation of the wrinkles of flange in the part of cup drawing by using aluminium alloy A1050 and A5052. This simulation is used by the explicit finite elements code $PAM-STAMP^{TM}$. The computed results are compared with the experimental results to show the validity of the analysis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.94-100
• /
• 2004

We fabricated textured Ag substrates for YBCO coated conductor and evaluated the effects of annealing temperature on microstructural evolution, texture formation, and surface morphology. Ag ingot, as an initial specimen, was prepared by plasma arc melting(PAM). Subsequently, the ingot was cold rolled to 100 ${\mu}{\textrm}{m}$ thick tape and annealed at temperatures of 600-80$0^{\circ}C$. The texture and surface morphology of the substrate were characterized by pole-figure and atomic force microscopy(AFM) profile, respectively. It was observed that a strong ｛110｝<110> texture was formed after annealing and its symmetry improved as annealing temperature increased. The full-width at half-maximum(FWHM) of ｛110｝<110> pole was as sharp as 10$^{\circ}$ for the substrate annealed at 80$0^{\circ}C$. On the other hand, it was found that the thermal grooving and faceting became remarkable as annealing temperature increased : root-mean-square(RMS) roughness of the substrate annealed at 80$0^{\circ}C$ was 39.2 nm. The substrate of strong texture and smooth surface, fabricated in our study, is considered to be suitable for use as a substrate for the epitaxial deposition of superconductor film.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.48-53
• /
• 2002

Sheet or plate bending is one of the most important industrial metal forming processes. And considerable attention has been focused on gaining a better understanding of many of bending characteristics. One of defaults in bending process is the springback. In this study, the springback characteristics of tailor-welded strips in U-bending process was investigated. Furthermore, not only the relationships between the springback and the process variables such as the geometry of the tools and thickness combination of workpiece but also the heat effect which affects the springback due to welding process was experimentally considered. First, tailor-welded strips are joined by the laser welding process and consisted of two types of thickness combinations of the SCPI sheet, 0.8t${\times}$1.2t and 0.8${\times}$1.6t to investigate the effect of different thickness combination on the springback. Secondly, two different directionally welded strips, one was welded along the centerline of the strip-width and the other was along the centerline of strip-length, were adopted to compare the effects of the location of weld line on the springback. And three punch profile radii of 3, 9, and 15 m were used. Some cases of the experimental results were simulated by using a commercial FEM code, PAM-STAMP to compare the experimental results to the analytical ones.

• Journal of Contemporary Eastern Asia
• /
• v.8 no.2
• /
• pp.27-43
• /
• 2009

A ban on political podcasting during the General Elections 2006 in Singapore was justified by the Singaporean government on the grounds that the new medium had a greater power to influence voters than traditional modes of political discourse. A between-subjects controlled experiment was conducted to test whether podcasts of political speeches had a greater power to influence voters' evaluations of political candidates and likelihood of voting for them than online text-based transcripts of the same speeches. The study also examined whether mere exposure to political speeches online, irrespective of the modality, had an effect on voters' more general political preferences, i.e. the likelihood of support and voting for the opposition. The findings suggest that political podcasts were no more persuasive than text-based websites and that the effects on political preferences, if any, were likely due the exposure to political content online, not because of the nature of the medium. The implications of the findings are discussed.

• Structural Engineering and Mechanics
• /
• v.12 no.5
• /
• pp.459-474
• /
• 2001

The complete moment-curvature curves of doubly reinforced concrete beams made of normal- or high-strength concrete have been evaluated using a newly developed analytical method that takes into account the stress-path dependence of the constitutive properties of the materials. From the moment-curvature curves and the strain distribution results obtained, the post-peak behavior and flexural ductility of doubly reinforced normal- and high-strength concrete beam sections are studied. It is found that the major factors affecting the flexural ductility of reinforced concrete beam sections are the tension steel ratio, compression steel ratio and concrete grade. Generally, the flexural ductility decreases as the amount of tension reinforcement increases, but increases as the amount of compression reinforcement increases. However, the effect of the concrete grade on flexural ductility is fairly complicated, as will be explained in the paper. Quantitative analysis of such effects has been carried out and a formula for direct evaluation of the flexural ductility of doubly reinforced concrete sections developed. The formula should be useful for the ductility design of doubly reinforced normal- and high-strength concrete beams.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.374-377
• /
• 2008

Magnesium alloy sheets are usually formed at temperatures between $150^{\circ}C$and $300^{\circ}C$ because of their poor formability at room temperature. In the present study, the formability of AZ31B magnesium alloy sheets was investigated by the analytical and experimental approaches. First, tensile tests and the limit dome height test were carried out at elevated temperatures to get the mechanical properties and forming limit diagram, respectively. And then deep drawing of cross shaped die was tried to get the minimum corner radius and forming limit at specific temperature. Blank shape, punch velocity, minimum corner radius, fillet size, etc, were determined by finite element analysis physical try-outs. Especially, optimum punch and die temperature were suggested through the temperature-deformation analysis using Pam-stamp.

• ETRI Journal
• /
• v.45 no.1
• /
• pp.163-170
• /
• 2023

We report an electroabsorption modulator (EAM)-integrated distributed Bragg reflector laser diode (DBR-LD) capable of supporting a high data rate and a wide wavelength tuning. The DBR-LD contains two tuning elements, plasma and heater tunings, both of which are implemented in the DBR section, which have blue-shift and red-shift in the Bragg wavelength through a current injection, respectively. The light created from the DBR-LD is intensity-modulated through the EAM voltage, which is integrated monolithically with the DBRLD using a butt-joint coupling method. The fabricated chip shows a threshold current of approximately 8 mA, tuning range of greater than 30 nm, and static extinction ratio of higher than 20 dB while maintaining a side mode suppression ratio of greater than 40 dB under a window of 1550 nm. To evaluate its modulation properties, the chip was bonded onto a mount including a radiofrequency line and a load resistor showing clear eye openings at data rates of 25 Gb/s nonreturn-to-zero and 50 Gb/s pulse amplitude modulation 4-level, respectively.

• Journal of Sensor Science and Technology
• /
• v.33 no.1
• /
• pp.30-33
• /
• 2024

The occurrence of harmful algae on the coast of Korea has been a cause of damage to the aquaculture industry and deterioration of the coastal ecosystem environment. A method is required to predict their outbreak in real-time at the site. Therefore, this study attempted to develop a small hybrid optical sensor and real-time monitoring system based on LiDAR that can be used in the field and laboratory and can be applied to various platforms. FMS-L specifically suggested the amount of Chlorophyll a (Chl a) in the sample by measuring and analyzing the fluorescence emitted by the irradiating light. The accuracy of FMS-L was verified by measuring the concentrations of standard Chlorophyll a substances and Margalfidinium polykirkoids. In addition, the precision was verified by comparing the measurement results of FMS-L using commercial equipment Phyto-PAM-II. This equipment is compact and easy to move. Therefore, it can be easily applied to field surveys, allows short time measurements (10 s), and can be applied at a distance of 10 m from the measurement site.

• Korean Journal of Environmental Agriculture
• /
• v.20 no.3
• /
• pp.155-161
• /
• 2001

This study was carried out to investigate cytotoxicity of paraquat or bentazone on NIH 3T3 fibroblasts, toxicity of paraquat or bentazone, and compensatory effects of 3-Methylcholanthrene(3-MC) on the rat liver. In order to MTT assay, the $5.0{\times}10^4$ cell/mL of NIH 3T3 fibroblast in each well of 24 multidish were cultured. After 24 hours, the cells were treated with solution of paraquat or bentazone(1, 25, 50, 100 ${\mu}M$ respectively). After the NIH 3T3 fibroblast of all groups were cultured in same condition for 48 hours. MTT assay were performed to evaluate the cytotoxicity of cell organelles. Paraquat or bentazone $MTT_{50}$ were 1668.97 ${\mu}M$ and 1506.97 ${\mu}M$, respectively. These $IC_{50}$ of paraquat or bentazone were decided low cytotoxicity by Borenfreund. In order to observe the toxicity and compensatory effects of paraquat or bentazone on the rat liver, Sprague-Dawley male rats were used as experimental animals and divided into paraquat or bentazone only treated group and simultaneous application group of paraquat or bentazone and 3-MC. At 30 min and 1, 3, 6, 12, 24, 48 and 96 hrs interval after each treatment, the animals were sacrificed by decapitation and liver were immediately removed, immersed in fixatives, and processed with routine method for light microscopic study. Paraffin sections were stained with H-E, PAM and Best Carmine. Under the light microscope, degenerative changes of hepatic lobules were frequently observed in portal area from 3 hrs after paraquat or bentazone treatment. All hepatic cells were induced degenerative change at 12 hrs and more severe degenerative change at 48 hrs after paraquat or bentazone treatment. Especially, hepatic cells of bentazone only treated group were distinctly showed pyknotic. Glycogen granules were increased in portal area at 3 hrs, all hepatic cells at 12 hrs and remarkably increased at 48 hrs after paraquat or bentazone treated group. But hepatic cells of bentazone only treated group were regeneration at 48 hrs from portal area and glycogen granules of hepatic cells of paraquat or bentazone and 3-MC combination treated group showed in central area only at 48 hrs. The results indicate that 3-MC may be decrease paraquat or bentazone cytotoxicity on the rat liver.