• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1585-1586
• /
• 2011

• Journal of Astronomy and Space Sciences
• /
• v.25 no.4
• /
• pp.459-470
• /
• 2008

DATS which is one of three subsystems of IDACS is responsible to receive Sensor Data, LRIT and HRIT in L-Band and transmit LRIT and HRIT in S-Band from/to COMS satellite. This paper shows detailed test procedures used to verify the performance and functionality of DATS after its implementation was completely finished. As a part of efforts to verify key DATS performance, G/T and EIRP were measured by using solar flux density as radio source. Regarding the verification of DATS functionality, RF loop-back test was conducted to validate if there is no BER degradation excepting MODEM/BB implementation loss occurred in the integrated DATS. Integrated with 13m antenna, DATS successfully restored image from received MTSAT-1R broadcasting data, LRIT and HRIT, of which frequencies are all L-Band. S-Band transmission was also verified through test antenna placed away from 13m antenna by measuring real LRIT and HRIT spectrum in S-Band. From those test results, DATS is determined to be fully ready to communicate with COMS in L-Band and S-Band.

• Journal of the Korean Vacuum Society
• /
• v.20 no.2
• /
• pp.146-154
• /
• 2011

The adhesive-tape of a liquid leak film sensor including the alarm system is developed. The sensing film is composed of three layers such as base film layer, conductive line layer, and protection film layer. The thickness of film is 300~500 um, the width is 3.55 cm, and the unit length is 200 m. On the conductive line layer, three conducting lines and one resistive line are formulated by the electronic printing method with a conducting ink of silver-nano size. When a liquid leaks for the electricity to be conducted between the conductive line and the resistive line, the position of leakage is monitored by measuring the voltage varied according to the change of resistance between two lines. The error range of sensing position of 200 m film sensor is ${\pm}1m$.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.325-330
• /
• 2000

A dynamic absorber is used to protect the primary vibration system under the steady-state harmonic disturbance. In a number of cases it appears expedient to install several absorbers of smaller masses instead of one. This may be due to the need of distribute the absorber's response along the construction, restrictions on the absorber's installation. So, we studied characteristics of the primary vibration system for the optimal natural frequency ratio and the optimal damping ratio of serial multi-dynamic absorber. Also we obtained the optimum values of the serial multi-dynamic absorber parameters using computer simulation for the damped primary vibration system. In designing multi-dynamic absorber, we presented for the optimal natural frequency and the optimal damping ratio of multi-dynamic absorbers.

• Journal of Biosystems Engineering
• /
• v.22 no.3
• /
• pp.363-370
• /
• 1997

Utilizing the tools such as CLIPS can reduce the time that it takes to develop expert systems. CLIPS is a development tool for expert system and has public inference engine and utilities. However, skilled programming is needed to run CLIPS on Windows 95, and proper interfaces for knowledge engineers or end-users who do not have good programming ability should be developed. Therefore, the user-friendly interfaces including htitle, hmenu, hyesno, htextdisplay, and hrun were developed and added to CLIPS. The intefaces were excuted in command-line mode of CLIPS on Windows 95. Also, htitle and hmenu can display graphic files for expert system users comprehension. An expert system was constructed using the interfaces and examples were displayed.

• Journal of Power System Engineering
• /
• v.3 no.1
• /
• pp.67-73
• /
• 1999

It is not easy to control the speed of AC motors accurately without modeling with some parameters for the controlled system. However, there are some application parts which do not require high speed responses strictly and the motor parameters can not to be identified simply. In this paper, a speed control method for a synchronous motor(S.M) with unknown parameters of the motor is investigated. The method is based on the current control algorithm. Speed controller and current controller are designed using PI control law. Some experiments are performed using DSP and power expert system to prove the validity of the proposed method. Throughout experimental results, the method is confirmed successfully. This method is expected to control the system with unknown parameters of the S.M efficiently.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.8-16
• /
• 1999

In this paper, the performance of a hybrid DS/SFH-SS(direct-sequence/slow-frequency-hopped spread-spectrum) system with coherent BPSK modulation over Nakagami fading channel in the presence of multiple tone jamming is analyzed. Because the Nakagami m-distribution can describe not only Rayleigh fading but also more general fluctuations involving a specular component by adjusting the value of the fading index m. It is known that for m=1 corresponds to Rayleigh fading, for $1/2{\le}m{\le}1$ corresponds to the worst case fading condition, for m>1 corresponds to Rician fading, and for $m{\to}{\infty}$ corresponds to the nonfading condition. The bit error probability is derived over Nakagami model and numerical evaluations are presented for some combinations of system parameters. The results show that as m increases, the bit error probability is better. Also, at a low JSR(jamming-to-signal power ratio), a pure DS-SS system can achieve lower bit error probability than a hybrid DS/SFH-SS system. But at a high JSR, a hybrid DS/SFH-SS system is shown to be superior to a pure DS-SS system. Therefore, it is demonstrated that without increasing the total system bandwidth, the performance of a hybrid DS/SFH-SS is superior to that of a pure DS-SS system in the presence of multiple tone jamming.

• Journal of the Korean Vacuum Society
• /
• v.15 no.5
• /
• pp.512-517
• /
• 2006

A reliable linear translation system was constructed. The system has six piezo legs, attached to a main body, holding a hexagonal sapphire rod. The sapphire rod moves either forward or backward with the sequential motion of the piezo legs, driven by characteristic electric voltage waves. The translational system was tested in vertical direction. The speed of the sapphire rod was turned out to be constant during several mm travel. The slowest upward speed was measured to be ${\sim}1.7{\times}10^{-6}m/s$, yielding ${\sim}28.3nm/step$, while the slowest upward speed was ${\sim}3.7{\times}10^{-6}m/s$, with ${\sim}61.7nm/step$, due to gravitational force. The velocity increases linearly, as the amplitude of the voltage waves increases. The linear translation system will be used as a coarse approach part for a scanning tunneling microscope.

• Journal of Korea Multimedia Society
• /
• v.10 no.9
• /
• pp.1153-1164
• /
• 2007

One of the most challenging technical issues in mobile communication for multimedia is Quality of Service (QoS) management of handover calls. This paper proposes a 2-level handover control system to copy with this problem. A 2-level handover control system consists of resource reservation and call admission control modules. The resource reservation module divides the network resource into Hard and Soft reserved resource. The Hard reserved resource is only for the handover calls while the Soft reserved resource is for both the handovers and the new calls. And also, the resource reservation module classifies handovers into primary and secondary handovers based on often they occur. The call admission control module deals with the primary and secondary handover calls in different ways. The new calls can use Soft reserved resource only if there is sufficient amount available in the Hard reserved resource. Proposed system is evaluated using an M/M/c/c queueing model. It is shown that proposed system allows more efficient utilization of network resource without degrading QoS comparing with the legacy handover control systems.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.5
• /
• pp.31-36
• /
• 1983

The indirect M.R.A.C. method using the W.L.S. algorithm is applied to the speed control of a D.C. motor on the assumption that the motor is the 1-st order, completely controllable and observable, non-minimum phase plant. By the help of M6809 microprocessor system the experiments are performed with respect to the sinusoidal and square reference input. The results show that the speed of a D.C. motor is well controlled by the indirect M.R.A.C. method using W.L.S, algorithm, and that the W.L.S. algorithm is quite suitable to the time-varying plant.