• Journal of Korea Multimedia Society
• /
• v.13 no.5
• /
• pp.641-650
• /
• 2010

Color image sensors (CIS) output color images through image sensors and image signal processing. Image sensors that convert light to electrical signal are divided into CMOS image sensor and CCD image sensor according to transferring method of signal charge. In general, a CIS has RGB output signals from tri-stimulus XYZ of the scene through image signal processing. This paper presents an adaptive colorimetric analysis method to obtain chromaticity and luminance using CIS under various environments. An image sensor for the use of colorimeter is characterized based on the CIE standard colorimetric observer. We use the method of least squares to derive a colorimetric characterization matrix between camera RGB output signals and CIE XYZ tristimulus values. We first survey the camera characterization in the standard environment then derive a SGL(shutter-gain-level) function which is relationship between luminance and auto exposure (AE) characteristic of CIS, and read the status of an AWB(auto white balance) function. Then we can apply CIS to measure luminance and chromaticity from camera outputs and AE resister values without any preprocessing. Camera RGB outputs, register values, and camera photoelectric characteristic are used to analyze the colorimetric results for real scenes such as chromaticity and luminance. Experimental results show that the proposed method is valid in the measuring performance. The proposed method can apply to various fields like surveillant systems of the display or security systems.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.455-461
• /
• 2013

Mar behavior and visibility were investigated by applying a constant load to various gloss-coated urethane-acrylate surfaces. Using a area-contact scratch tip which can apply a relatively low stress level to the coated surfaces, the mar damages were generated on the surfaces. When evaluating the mar-induced damage by means of delta-gloss (${\Delta}G$) and delta-luminance (${\Delta}L$) with existing test methodologies, an increase in constant load on the same gloss-coated surface leads to an increase in ${\Delta}G$ and ${\Delta}L$. However, these are not suitable for evaluating and comparing the surface damages of different gloss-coated samples because of a disagreement between the measured values and the mar visibility. It is shown that new mar test assessment proposed in this work not only can be used to quantitatively evaluate the mar damage, but also accounts for the correlation that the increases of the normalized gloss and luminance on coated surfaces correspond with an increase in the mar visibility.

• Science of Emotion and Sensibility
• /
• v.17 no.3
• /
• pp.3-14
• /
• 2014

Since the domestic introduction of iPhone in 2009, use of smartphones rapidly increased and many tasks, previously performed by various devices, are now performed by smartphones. In this process the importance of reading little text using small smartphone screen has become highly significant. This research tested how display factors of smartphone (pixel density, sub-pixel structure, luminance) and environmental factor (illumination) affect legibility related discomfort in text reading. The results indicated that legibility related discomfort is largely affected by pixel density, where people experience inconvenience when the pixel density becomes lower than 300 PPI. Illumination has limited effect on legibility related discomfort. Participants reported more legibility related discomfort when stimulus presented in various levels of illumination rather than single illumination level. Sub-pixel structure and luminance did not affected legibility related discomfort. Based on the results we suggest lower limit resolution of smart devices (smartphones, tablet computers) of different sizes for text legibility.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.4
• /
• pp.136-141
• /
• 2011

The lightshelf system reduces intense illumination levels of indoor from direct sun light and reflect to lead diffused light into indoor deeply. This study aims to design acurved-lightshelf by a ray tracing method and evaluate the daylighting performance of window integrated with the curved-lightshelf by computer simulations. For this purpose, evaluation test model was designed for the experiments to validate the simulation model, and the curved-lightshelf was designed by the ray tracing method using Ecotect. After the office model was designed using 3D simulation, the average indoor illuminance, luminance and distribution of illuminance were evaluated by simulation which has a algorithm of Radiosity and Ray-Tracing method under four different cases(case1;no lightshelf, case2; Flat board, case3; tilted at $30^{\circ}$ angle, case4; the curved-lightshelf). As results, it turns out that case1 showed higher average illuminance and case4 was more uniformly distributed than case2 and case3, In addition average luminance of case1 was also lower. indicating that the curved-lightshelf would reduce the possibility of the glare, while maintaining the sufficient daylight level.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.47-50
• /
• 2007

The maximum current level in organic light emitting diodes (OLED) panel influences the maximum pixel luminance, the width of $V_{DD}$ lines, the maximum power consumption and the lifetime. We propose an algorithm that limits the overall current without any palpable image artifacts, and therefore, improve panel parameters by program.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.229.2-229.2
• /
• 2016

본 연구에서는 Host와 Dopant $Ir(ppy)_3$의 도핑 위치 변화에 따른 bottom emission 인광 OLED를 제작하여 발광 효율 및 특성을 분석하였다. 소자의 EML은 $Ir(ppy)_3/CBP$와 $CBP/Ir(ppy)_3$ 순으로 증착하여 제작하였다. $Ir(ppy)_3/CBP$은 낮은 구동 전압에서 큰 전류밀도와 큰 luminance을 측정하였고, 반대로 $CBP/Ir(ppy)_3$은 높은 구동 전압에서 $CBP/Ir(ppy)_3$은 큰 전류밀도와 큰 luminance가 측정되었다. 이는 $Ir(ppy)_3/CBP$에서 HTL과 EML 사이에 hole direct injection이 발생으로 Hole이 증가하지만 charge balance 불일치로 roll-off가 발생하고, $CBP/Ir(ppy)_3$에서 electron direct injection에 의한 electron 증가로 charge balance가 향상된다. EL spectrum 측정에서 $Ir(ppy)_3$은 파장 512nm 발광이 일어나고, CBP와 NPB은 각각 파장 380nm, 433nm로 분석된다. 각 물질의 triplet의 전달은 energy level이 큰 곳에서 작은 곳으로 전달되는데 이러한 이유로 전압에 따른 recombination zone 변화로 각 물질에서 나오는 파장의 intensity가 달라지는 것을 확인하였다. $Ir(ppy)_3/CBP$은 낮은 전류 밀도에서는 CBP의 영향으로 380nm 파장대가 크고, 높은 전류 밀도에서는 $Ir(ppy)_3$의 영향으로 512nm 파장대가 크게 나오는 것을 확인했고, $CBP/Ir(ppy)_3$에서는 낮은 전류 밀도에서 512nm 파장대가 커지고, 큰 전류 밀도에서는 CBP에서 NPB로의 triplet 에너지 전달의 증가로 433nm 파장대가 커지는 것을 확인하였다.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.1
• /
• pp.24-27
• /
• 2013

In this paper, we investigated the effect of luminescence properties of various concentrations of magnesium-doped ZnS:Mn phosphor excited by plasma luminescence device. The PL intensity was evaluated in the range of 300~500 nm excitation wavelengths. We found the highest PL intensity of the phosphors excited by 365 nm and 450 nm was observed at Mg concentrations of 1.4 wt% and 0.8 wt%, respectively. In addition, an emission peak was distinguished at 580 nm wavelength. With increasing Mg dopant level, enhanced PL intensity was observed, which is possibly applicable to color converting materials by blue emission for white light sources. Finally, we evaluated the luminance properties of color converting ZnS:Mn,Mg phosphors with plasma blue light source. the white luminance of plasma light source with CIE(0.36,0.26) was established by color converting phosphors of ZnS:Mn with 0.8 wt% Mg.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.2
• /
• pp.211-224
• /
• 1994

In this paper, a multi-level adaptive intraframe method has been proposed to separate the luminance and chominance components in NTSC composite signal. The control signals are generated by detecting the vertical correlation and transition in the horizontal and diagonal directions. The chrominance component is adaptively processed through vertical and horizontal filters according to the control signals and the luminance component is processed by subtracting the chrominance component from the composite video signal. The several filters have been used at the sampling rate of four times the color subcarrier frequency and computer simulation and SVP(Serial Video Processing) system have been introduced to compare the performance of the conventional methods and that of proposed one.

• Journal of Information Display
• /
• v.7 no.2
• /
• pp.26-30
• /
• 2006

Insertion of a thin lithium fluoride (TLF) layer between an emitting layer (EML) and an electron transporting layer has resumed in the developement of a highly efficient and bright organic light-emitting diode (OLED). Comparing with the performance of the device as a function of position with the TLF layer in tris-(8-hydroxyquinoline) aluminum $(Alq_{3})$, we propose the optimal position for the TLF layer in the stacked structure. The fabricated OLED shows a luminance efficiency of more than 20 cd/A, a power efficiency of 12 Im/W (at 20 mA/$cm^{2}$), and a luminance of more than 22 000 cd/$m^{2}$ (at 100 mA/$cm^{2}$), respectively. We suggest that the enhanced performance of the OLED is probably attributed to the improvement of carrier balance to achieve a high level of recombination efficiency in an EML.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.409-412
• /
• 2006

EEFL can be driven by square wave driving method. A square wave is applied directly to both ends of EEFL by cascaded multi-stage full-bridge inverter. The various current shapes of lamp are achieved by various inductors between lamp and inverter. In this paper, it is newly investigated that the area of current directly influences the luminance. Furthermore, the 3-level square wave is considered to drive EEFL with self-discharge characteristics. The highest luminance efficiency is achieved by properly controlling the rate of self-discharge usage.