• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.136-141
• /
• 2008

Due to environmental concerns $CO_2$ has been reintroduced as a potential candidate to replace HFCs in refrigeration systems since 1990s. In a refrigeration cycle, oil is utilized in lubricating a compressor. However, although oil separators are installed after a compressor oil is prone to leak to the whole system. The mixing of $CO_2$ and oil, even a small amount of oil, the heat transfer performance in heat exchanger deteriorated and the pressure drop inside tube increases. Therefore, it is needed to precisely estimate the mixture thermodynamic properties of $CO_2$-lubricant oil to correctly design a $CO_2$ refrigeration system. The commonly used method in estimating the mixture properties is the mole based weighting model. However, the accuracy of the method can not be assured. In the present study, $CO_2$-lubricant oil mixture properties including viscosity and density were estimated by using the mixture models, based on the equation of state (EOS).

• Tribology and Lubricants
• /
• v.35 no.3
• /
• pp.190-198
• /
• 2019

Gas foil bearings (GFBs) enable small- to medium-sized turbomachinery to operate at ultra-high speeds in a compact design by using ambient air or process gas as a lubricant. When using air or process gas, which have lower viscosity than lubricant oil, the turbomachinery has the advantage of reduced power loss from bearing friction drag. However, GFBs may have high Reynolds number, which causes turbulent flows due to process gas with low viscosity and high density. This paper analyzes gas foil journal bearings (GFJBs) with high Reynolds numbers and studies the effects of turbulent flows on the static and dynamic performance of bearings. For comparison purposes, air and R-134a gas lubricants are applied to the GFJBs. For the air lubricant, turbulence is dominant only at rotor speeds higher than 200 krpm. At those speeds, the journal eccentricity decreases, but the film thickness, power loss, and direct stiffness and damping coefficients increase. On the other hand, the R-134a gas lubricant, which that has much higher density than air, causes dominant turbulence at rotor speeds greater than 10 krpm. The turbulent flow model predicts decreased journal eccentricity but increased film thickness and power loss when compared with the lamina flow model predictions. The vertical direct stiffness and damping coefficients are lower at speeds below 100 krpm, but higher beyond that speeds for the turbulent model. The present results indicate that turbulent flow effects should be considered for accurate performance predictions of GFJBs with high Reynolds number.

• Transactions of Materials Processing
• /
• v.29 no.2
• /
• pp.113-117
• /
• 2020

Various parameters are involved in the frictional behavior of steel sheet during stamping. We performed various tests in order to investigate the influence of tool surface texture directionality upon the resulting friction in sheet forming processes. Four different tools were manufactured which gave us a range of roughness for both parallel and transverse texture directions. Each of the tools was examined in flat type friction tests under identical test conditions. The tool with the transverse surface texture produces significantly lower levels of friction than the tool with parallel texture direction. Considering the lubrication mechanism associated with transverse texture, one can imagine the lubricant being constantly supplied from the reservoir of the micro valley to the point of contact and hence producing the lower levels of friction seen.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.982-984
• /
• 2008

Generally, the soil around railroad is contaminated by the leakage of oil during its maintenance or the operation of rolling stock. Because the railroad soil is located under ballast and is hardened with the designated strength due to safety, the characteristics of the polluted site are different. In this study, the phenomena of oil diffusion in the railroad site was investigated using 2-D reactor. The used oil was lubricant. As a result, the maximum diffusion depth of lubricant was about 9.5 cm due to its high viscosity and the hardened soil. The lubricant was diffused by gravity more than by horizontal migration. In the future, these results can be applied to develop a remediation method for the contaminated railroad soil.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.22-31
• /
• 1993

The thermohydrodynamic performance of large tilting pad journal bearings is analyzed, taking into account the three dimensional variation of lubricant viscosity. The eddy viscosity model based on wall formula is applied. The effects of temperature rise and turbulence on the bearing performance are studied in comparision with the isothermal or the laminar analysis. It is shown that these effects have significant influence on temperature distribution, load capacity and power loss of the bearing.

• Tribology and Lubricants
• /
• v.31 no.6
• /
• pp.245-250
• /
• 2015

This study investigates the lubrication characteristics of fuel injection pumps with reference to different fuel oils. Medium-speed diesel engines use fuel oils with various viscosities, such as heavy fuel oil (HFO, which is a high-viscosity fuel oil) and light diesel oil (LDO, which is a low-viscosity fuel oil). When fuel oil with a low viscosity is used, both fuel oil and lubricating oil lubricate the system. Thus, the lubrication of the fuel injection pump is in a multi-viscosity condition when the fuel oil in use changes. We suggest three cases of multi-viscosity models, and divide the fuel injection pump into three lubrication sections: a, the new oil section; b, the mixed oil section; and c, the used oil section. This study compares the lubrication characteristics with variation of the multi-viscosity model, clearance. The volume of Section b does not affect the lubrication characteristics. The lubrication characteristics of the fuel injection pump are poor when high-viscosity fuel oil transfers to low-viscosity fuel oil. This occurs because the viscosity in the new oil section (i.e., Section a) dominates the lubrication characteristics of the fuel injection pump. However, the lubricant oil supply in the used oil section (i.e., Section c) can improve the lubrication characteristics in this condition. Moreover, the clearances of the stem and head significantly influence the lubrication characteristics when the fuel oil changes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.451-452
• /
• 2010

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.11
• /
• pp.733-738
• /
• 2008

Due to environmental concerns $CO_2$ has been reintroduced as a potential candidate to replace HFCs in refrigeration systems. Oils are always required in a vapor-compression cycle, and thus it is necessary to precisely estimate the thermodynamic mixture properties of $CO_2$-lubricant oil. In the present study, the density and the viscosity of the mixture was calculated by the Redlich and Kwong type EoS and the modified Peng and Robinson type viscosity EoS, respectively. The viscosity model was based on the similarity between P-v-T and T-$\mu$-P relationships. The predicted results were compared with the experimental data of Pens ado et al. whose test conditions were 100$\sim$650 bar of pressure and 303 K$\sim$353 K of temperature with the $CO_2$-POEs mixtures under 92.2 wt.% and 83.3 wt.% of $CO_2$ concentration. The mean deviations of the mixture density were 7.93% and 8.32% for 92.2 wt.% and 83.3 wt.% of $CO_2$ concentration, respectively. Concerning the viscosity, the mean deviations were 4% and 10% for 92.2 wt.% and 83.3 wt.% of $CO_2$ concentration under the Pensado et al.'s test conditions.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.85-93
• /
• 1998

The Bair & Winer's limiting shear stress rheological model is incorporated into the Reynolds equation to successfully predict the traction and film thickness for an isothermal line contact using the primary rheological properties. The modified WLF viscosity model and Barus viscosity model are also adapted for the realistic prediction of EHD tractional behavior. The influences of the limiting shear stress and slide-roll ratio on the pressure spike, film thickness, distribution of shear stress and nonlinear variation of traction are examined. A good agreement between the disc machine experiments and numerical traction prediction has been established. The film thickness due to non-Newtonian effects does not deviate significantly from the fdm thicknesss with Newtonian lubricant.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.359-365
• /
• 1999

We have evaluated the performance and some physical properties of 25 automotive engine oils (21 domestic and 5 imported products) which are purchased on the market to verify the API(American Petroleum Institute) or ILSAC(International Lubricant Standardization and Approval Committee) certification marks attached on the products and to determine the necessity of the quality control of the engine oils on the market. 12 test items are chosen according to API engine oil specification, which are flash point, pour point, cold cranking simulator apparent viscosity, pumping viscosity, gelation index, HTHS(High Temperature High Shear viscosity), foam, high temperature foam, filterability, volatility, high temperature deposit(TEOST), phosphorus content. We have found one product which did not meet the API specification on gelation index, one on HTHS, four on foam, and one on volatility, which implies that the quality control system is in need to check the fidelity of the certification marks attached on the engine oils being marketed. In addition, this works raises the necessity of the upgrade of the present Korean engine oil specification.