• Journal of Power Electronics
• /
• v.6 no.3
• /
• pp.235-244
• /
• 2006

Recently, speed sensorless vector control for synchronous reluctance motors (SYRMs) has deserved attention because of its advantages. Although rotor angle calculation using flux estimation is a straightforward approach, the DC offset can cause an increasing pure integrator error in this estimator. In addition, this method is affected by parameter fluctuation. In this paper, to control the motor at the low speed region, a modified programmable cascaded low pass filter (MPCPLF) with sensorless online parameter identification based on a block pulse function is proposed. The use of the MPCLPF is suggested because in programmable, cascade low pass filters (PCLPF), which previously have been applied to induction motors, the drift increases vastly wl)en motor speed decreases. Parameter identification is also used because it does not depend on estimation accuracy and can solve parameter fluctuation effects. Thus, sensorless speed control in the low speed region is possible. The experimental system includes a PC-based control with real time Linux and an ALTERA Complex Programmable Logic Device (CPLD), to acquire data from sensors and to send commands to the system. The experimental results show the proposed method performs well, speed and angle estimation are correct. Also, parameter identification and sensorless vector control are achieved at low speed, as well as, as at high speed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.10
• /
• pp.708-711
• /
• 2000

Sensorless PMSM is much studied for the industrial applications and home appliances because a mechanical sensor reduce reliability and increase cost. Most of sensorless algorithms are based on motor equations, and so the magnitude of phase voltage and current should be exactly obtained. However, the inverter output voltage applied to PMSM has relatively large error in the low speed range, and a relatively poor response is shown in the low speed range. This paper investigates the improved performance of sensorless PMSM in the low speed range. This paper proposes the error reduction of inverter output voltage which is realized through the variable link voltage. The proposed algorithm is verified through simulation and experiment.

• Journal of Power Electronics
• /
• v.5 no.1
• /
• pp.11-19
• /
• 2005

This paper describes the two control techniques to perform the sensorless vector control of a PMSM by injecting the high frequency voltage to the stator terminal. The first technique is the estimation algorithm of the initial rotor position. A PMSM possesses the saliency which produces the ellipse of the stator current when the high frequency voltage is injected into the motor terminal. The major axis angle of the current ellipse gives the rotor position information at a standstill. The second control technique is a sensorless control algorithm that injects the high frequency voltage to the stator terminal in order to estimate the rotor position and speed. The rotor position and speed for sensorless vector control is calculated by appropriate signal processing to extract the position information from the stator current at low speeds or standstill. The proposed sensorless algorithm using the double-band hysteresis controller exhibits excellent reference tracking and increased robustness. Experimental results are presented to verify the feasibility of the proposed control schemes. Speed, position estimation and vector control were carried out on the floating point processor TMS320VC33.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.4
• /
• pp.641-647
• /
• 2004

By most sensorless speed control schemes for induction motor. the control performances in high speed range are good, but it is difficult to obtain satisfactory results in low speed region. This paper proposes a new method controlling the low and the high speed regions separately to attain the stable operation in the overall range. The current error compensation method, in which the controlled stator voltage is applied to the induction motor so that the error between stator currents of the numerical model and the actual motor can be forced to decay to zero as time proceeds. is used in the low speed region In the high speed region. the method with adaptive observer is utilized. This control strategy contains an adaptive state observer for flux estimation. The rotor speed can be calculated from the rotor flux and the motor currents. The experimental results indicate good speed and load responses from the very low speed range to the high, and also show accurate speed changing performance between the low and the high speed range.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2474-2479
• /
• 2012

A sensorless vector control of an induction motor provides a good performance in the middle and high speed region. However, in the low speed region, it is very difficult to implement the sensorless vector controller because the feeding voltage measured by the motor is very low. In this paper, to improve the performance of a sensorless vector control of an induction motor in the low speed region under 3Hz, we proposed the fuzzy logic controller using the zooming algorithm. To verify the performance of the proposed controller, an experiment has been performed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.2
• /
• pp.90-98
• /
• 2004

Variable-speed drives are being continually innovated. Recently, sensorless induction motor drives have been much studied due to several advantages. Most sensorless algorithms are based on the mathematical modeling of motors, and all the information is obtained from the monitored voltages and currents. Therefore, the accuracy of such variables largely affects the performance of a sensorless induction motor drive. However, the output voltage of the SVPWM-VSI which is widely used in a sensorless induction motor drive has a considerable error, especially in a low speed range. This paper proposes a variation of the dc link voltage as a high-performance strategy for overcoming the above problem. The proposed strategy leads to an improved resolution of the output voltage of the SVPWM-VSI in a sensorless induction motor drive. Simulation and experiment have been performed for the verification of the proposed strategy.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.82-87
• /
• 2011

In this paper, a sensorless speed control system is designed for the next generation high speed railway at zero and low speed region. The applied vector control scheme is a maximum torque per ampere(MTPA) method to utilize reluctance torque of IPMSM. The designed sensorless control scheme is a rotating high frequency voltage signal injection method. To verify the designed system, a simulator for the vector controller and sensorless controller is implemented using Matlab/simulink.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.119-122
• /
• 2003

This paper describes the sensorless technique for the surface-mounted permanent-magent synchronous motor(SPMSM or PMSM) drive based on magnetic saliency. The control technique is a sensorless control algorithm that injects the high frequency voltage to the stator terminal in order to estimate the rotor position and speed. The rotor position and speed for sensorless vector control is achieved by appropriate signal processing to extract the position information from the stator current in the low speed range including zero speed. Proposed sensorless algorithm using the double-band hysteresis controller and initial rotor position detection exhibits excellent reference tracking and increased robustness. Experimental results are presented to verify the feasibility of the proposed control schemes.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1582-1591
• /
• 2014

This paper presents a hybrid sensorless control for an interior permanent magnet synchronous motor (IPMSM) for zero-, low-, and high-speed regions. Many sensorless control methods such as an observer-based estimator have been introduced. However, most of the observer-based estimators have a disadvantage at start-up and in the low-speed region. To solve this problem, a simple strategy of using a hybrid system is proposed by integrating a high-frequency (HF) signal injection method and a full-order flux observer. In addition, an HF signal injection method with only a low pass filter (LPF) is proposed to simplify the hybrid system. The hybrid system achieves high-performance drive throughout the entire speed range. The effectiveness of the proposed hybrid technique is verified by experiments using an 11-kW IPMSM drive system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.9
• /
• pp.692-699
• /
• 2003

A novel rotor speed estimation method using Model Reference Adaptive Control(MRAC) is proposed to improve the performance of a sensorless vector controller. In the proposed mettled, the stator current is used as the model variable for estimating the speed. In conventional MRAC methods, the relation between the two model errors and the speed estmation error is unclear. Yet, in the proposed method, the stator current error is represented as a function of the first degree for the error value in the speed estimation. Therefore, the proposed method can produce a fast speed estimation and is robust to the parameters error In addition, the proposed method of offers a considerable improvement in the performance of a sensorless vector controller at a low speed. The superiority of the proposed method is verified by simulation and experiment in a low speed region and at a zero-speed.