• 동력기계공학회지
• /
• 제17권4호
• /
• pp.72-78
• /
• 2013

Compacted graphite iron 340 was carried out the heat treatment from 873 to 1,273 K. Compacted graphite iron 340 was evaluated relationship between the sound velocity, the attenuation coefficient and the tensile strength. The obtained results are as following. The signal strength of C scan images were weak according to increasing of heat treatment temperature and time. The amplitude of A scan and B scan was also low. This can be cause that the graphite was grown into the type of vermicular, and the many of grain boundary with ultrasound scattering were increase. The sound velocity was depend upon the heat treatment temperature and time, the attenuation coefficient had nothing to do with the temperature and time. The higher the heat treatment temperature, the tensile strength and the sound velocity were decreased. However, the tensile strength was proportional to the sound velocity. The higher tensile strength, the faster the sound velocity.

• 플랜트 저널
• /
• 제6권4호
• /
• pp.56-62
• /
• 2010

This study investigated characteristics of the post-weld heat treatment of SA213-T23, which was developed for water wall of the ultra super critical power boiler. The temperature of post weld heat treatment should be $730^{\circ}C$ or higher to reduce hardness of the deposit metal and heat affected zone. Coincidently, the temperature should remain $760^{\circ}C$ or lower to prevent hardness of the base metal from dropping. Hardness decline of deposit metal was trivial according to time when the holding time of heat treatment at $740^{\circ}C$ of post-weld heat treatment gradually increased from initial 15 minutes.

• Elastomers and Composites
• /
• 제43권4호
• /
• pp.259-263
• /
• 2008

저밀도 폴리에틸렌에 대한 장시간 저온 열처리가 저밀도 폴리에틸렌 고분자의 결정화도에 미치는 효과를 고체 수소 핵자기공명을 이용하여 연구하였다. 장시간 열처리는 첫째, 저밀도 폴리에틸렌의 색깔을 엷은 노란색으로 변하게 하였고 둘째, 저밀도폴리에틸렌에서 수소 핵의 스핀-스핀 및 스핀-격자 완화시간을 증가시켰으며, 셋째, 결정화도를 줄어들게 하였다. 먼저, $T_1$의 증가를 저밀도폴리에틸렌의 전체 스핀-격자 완화시간을 결정하는 비정질 영역의 부피 감소에 의한 것이거나 분자간 가교나 수소결합에 의한 특정 분자 운동 성분의 느려짐에 의해 발생하는 것으로 고려하였다. 하지만 결정화도의 감소는 열처리에 의한 비정질 영역의 감소를 의미하므로 전자와는 배치되었다. 따라서 $T_1$의 증가는 후자에 의한 결과임을 알 수 있었다.

• 열처리공학회지
• /
• 제24권4호
• /
• pp.187-192
• /
• 2011

Effect of austenitizing temperatures on the impact value of the AISI 4140 steel after repetition of spheroidization and cold deep drawing treatment has been studied. Sufficient dissolution of carbide was shown after austenitizing at the high temperature of $950^{\circ}C$. Accordingly, the impact value was remarkably increased by tempering of this high temperature austenitized steel at the tempering temperature ranges between $570^{\circ}C$ and $630^{\circ}C$. On the other hand, remarkable decrease in the impact values and elongations were shown by tempering the low temperature-austenitized ($870^{\circ}C$) steel due to the coarsening of undissolved-carbide existed at the austenitizing temperature.

• 열처리공학회지
• /
• 제29권1호
• /
• pp.1-7
• /
• 2016

Titanium and its alloys can be usually joined with brazing method. And the alloys should be brazed at low temperature to keep their original microstructure. In this study, the mechanical strength and microstructure of the CP-Ti joint-brazed with $Zr_{54}Ti_{22}Ni_{16}Cu_8$ filler metal having melting temperature of $774{\sim}783^{\circ}C$ were investigated. The tensile strengths of the joint-brazed at $800^{\circ}C$ with $100^{\circ}C/min$ of cooling rate showed more than 400 MPa which was as high as base metal. The $Widmanst{\ddot{a}}tten$ structure consisting of Ti and $Ti_2Ni$ phase was observed in the joint area. However, the tensile strengths of the joint-brazed at $800^{\circ}C$ with $15^{\circ}C/min$ of cooling rate were decreased and the Ti, $(Ti,Zr)_2Ni$ and $Ti_2Ni$ phases were observed at the joint area. It is believed that the $(Ti,Zr)_2Ni$ laves phases could decrease the mechanical strength of the joint and the cooling rate should be controled to get high strength of the titanium joint.

• Mycobiology
• /
• 제46권3호
• /
• pp.242-253
• /
• 2018

Onion (Allium cepa L.) is one of the major vegetable crops in Korea that are damaged and lost by pathogenic fungal infection during storage due to a lack of proper storage conditions. The aim of this study was to determine an appropriate control measure using thymol to increase the shelf life of onions. To control fungal infections that occur during low-temperature storage, it is necessary to identify the predominant fungal pathogens that appear in low-temperature storage houses. Botrytis aclada was found to be the most predominant fungal pathogen during low-temperature storage. The antifungal activity of the plant essential oil thymol was tested and compared to that of the existing sulfur treatments. B. aclada growth was significantly inhibited up to 16 weeks with spray treatments using a thymol solution. To identify an appropriate method for treating onions in a low-temperature storage house, thymol was delivered by two fumigation treatment methods, either by heating it in the granule form or as a solution at low-temperature storage conditions (in vivo). We confirmed that the disease severity was reduced up to 96% by fumigating thymol solution compared to the untreated control. The efficacy of the fumigation of thymol solution was validated by testing onions in a low-temperature storage house in Muan, Jeollanam-do. Based on these results, the present study suggests that fumigation of the thymol solution as a natural preservative and fungicide can be used as an eco-friendly substitute for existing methods to control postharvest disease in long-term storage crops on a commercial scale.

• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.125-130
• /
• 2008

Conventional plasma carburizing or nitriding for austenitic stainless steels results in a degradation of corrosion resistance. However, a low temperature plasma surface treatment can improve surface hardness without deteriorating the corrosion resistance. The 2-step low temperature plasma processes (the combined carburizing and post nitriding) offers the increase of both surface hardness and thickness of hardened layer and corrosion resistance than the individually processed low temperature nitriding and low temperature carburizing techniques. In the present paper, attempts have been made to investigate the influence of the introduction of Ar gas (0~20%) in nitriding atmosphere during low temperature plasma nitriding at $370^{\circ}C$ after low temperature plasma carburizing at $470^{\circ}C$. All treated specimens exhibited the increase of the surface hardness with increasing Ar level in the atmosphere and the surface hardness value reached up to 1050 HV0.1, greater than 750 $HV_{0.1}$ in the carburized state. The expanded austenite phase (${\gamma}_N$) was observed on the most of the treated surfaces. The thickness of the ${\gamma}_N$ layer reached about $7{\mu}m$ for the specimen treated in the nitriding atmosphere containing 20% Ar. In case of 10% Ar containing atmosphere, the corrosion resistance was significantly enhanced than untreated austenitic stainless steels, whilst 20% Ar level in the atmosphere caused to form CrN in the N-enriched layer (${\gamma}_N$), which led to the degradation of corrosion resistance compared with untreated austenitic stainless steels.

• 한국작물학회지
• /
• 제48권5호
• /
• pp.397-401
• /
• 2003

This experiment was conducted to know the characteristics of kernel growth as affected by various temperature regimes during grain filling using the varieties Hwaseongbyeo, Ilpumbyeo and Chucheongbyeo. The rice plants tested were grown in the natural condition at 1/5000a Wagner pots until flowering. After flowering, the rice plants were moved to controlled temperature conditions in a phytotron. The minimum/maximum daily temperature in the phytotron was controlled by 12/18, 15/21, 18/24, 21/27, and 24/$30^{\circ}C$, respectively. The grain weights were measured every three days after treatment. The mean daily kernel growth rate during active grain filling period showed different responses among varieties under various temperature regimes. The kernel growth rate of Chucheongbyeo was seriously reduced as temperature regimes were decreased. However, that of Ilpumbyeo was not influenced so critically. Ilpumbyeo showed some advantages in grain filling under low temperature regimes compared to Chucheongbyeo. The lag phase in grain filling of Chucheongbyeo was the longest among tested varieties, followed by Hwaseongbyeo under daily mean temperature regime of $15^{\circ}C$. Kernel weight of Ilpumbyeo increased fast in early grain filling phase under low temperature. This characteristic may be favorable for grain filling in temperate zone where the daily mean temperature is drastically dropped during grain filling period. Regression analysis with kernel growth rate and temperature showed the estimated critical low temperature for grain filling among varieties were $9^{\circ}C$, $12^{\circ}C$, $13^{\circ}C$ in Ilpumbyeo, Hwaseongbyeo and Chucheongbyeo, respectively. Under moderate temperature the duration of grain filling of Ilpumbyeo was longer than that of Chucheongbyeo. However, Under low temperature that of Ilpumbyeo was more favorable than Chucheongbyeo.

• 한국환경과학회지
• /
• 제25권4호
• /
• pp.535-542
• /
• 2016

This study was conducted to investigate effects of waterlogging on the growth, physiological responses, and yield of Kimchi cabbage. The growth of Kimchi cabbage with applied optimized air temperature (set to $20^{\circ}C$) was greater than those with high air temperature (set to $30^{\circ}C$) and the growth significantly decreased by severe waterlogging treatment. The net photosynthetic rate of outer leaves on one hour after waterlogging treatment was higher at 72 hours waterlogging treatment in $20^{\circ}C$ and lower at 24 hours of waterlogging treatment in $30^{\circ}C$. The root activity was decreased by the elevation of waterlogging periods in $20^{\circ}C$ treatment and lower by the short of waterlogging periods in $30^{\circ}C$ treatment. The ratio of formality with non-waterlogging treatment was approximately 64% under $20^{\circ}C$ air temperature and that of range was from 16 to 30% under $30^{\circ}C$. The yield under $20^{\circ}C$ showed higher than that under high air temperature. The non-waterlogging treatment in $20^{\circ}C$ had 4,463 kg/10a, which was the greatest among all treatments, while yields of non-waterlogging treatment at $30^{\circ}C$ were significantly low as 1,082 kg/10a. Results suggested that additional drainage work should be needed to overcome waterlogged conditions of open field during heavy rainfall and should be drainage as soon as possible if there are waterlogging.

• 한국산림과학회지
• /
• 제51권1호
• /
• pp.22-35
• /
• 1981

본(本) 연구(硏究)는 일본(日本) 및 한국(韓国國)에서 내한성(耐寒性)이 강(強)하다고 생각되는 삼(杉)나무 클론 및 품종(品種)에 인공적(人工的)인 고온(高温) 및 저온처리(低温處理)를 했을 때 내한성(耐寒性)이 변화(変化)하는 정도(程度)에 있어서 품종간(品種間)의 차이(差異)를 알기 위하여 설계(設計) 되었다. 고온처리(高温處理)는 상대습도(相対湿度) 100%하(下)에 $15^{\circ}C$에서 $20^{\circ}C$로 1일(日)에서 9일간(日間), 저온처리(低温處理)는 $-7^{\circ}C$로 1일(日) 3일간(日間) 실시(実施)되었으며 몇 경우에는 고온처리(高温處理)에 잇따라 저온처리(低温處理)가 실행(実行)되었다. 고온처리후(高温處理後) 내한성(耐寒性)을 작게 저하(低下)시키거나 저온처리후(低温處理後) 내한성(耐寒性)을 크게 증진(増進)시키는 수목(樹木)의 능력(能力)을 자연(自然)에서 일어나는 이학적(異学的)인 기후변동하(気候変動下)에서의 적응력(適応力)을 측정(測定)하는 지표(指標)로 삼고 1977~1980년(年)의 겨울 동안 초겨울, 한겨울, 초봄의 세 시기(時期)에 모두 내한성(耐寒性) 품종(品種)을 선발(選拔)하였던 바 이들 품종(品種)은 서울 7호(號), 9호(號), 남부(南部)3호(號), 4호(號), 성강(盛岡) 11호(號), 청삼(靑森) 8호(號), 흑석(黑石) 9호(號)로 나타났다. 이들 선발(選拔)된 품종(品種)은 초상(初霜)과 만상(晩霜)에 뿐만 아니라, 삼나무에 잘 일어나는 기부(基部)의 동해(凍害), 즉 지면(地面)에 가까운 지제부(地際部)가 고온(高温)에 의하여 내한성도(耐寒性度)가 저하(低下)되므로서 발생(発生)되는 유묘(幼苗)의 치명적(致命的)인 피해(被害)에 다른 품종(品種)들보다 비교적 강(強)하리라고 고찰(考察)되었다. 내한성(耐寒性) 및 고온(高温) 저온처리후(低温處理後) 내한성(耐寒性) 변화(変化) 속도(速度)에 있어서 품종간(品種間) 또는 동일품종내(同一品種內) 개체간(個体間)에 변이(変異)가 큰 것이 발견(発見)되었으며 이러한 변이(変異)는 그 품종(品種)이 선발(選拔)된 기후적(気候的) 조건(條件)과는 관련이 없었으나 앞으로 보다 내한성(耐寒性)이 강(強)한 삼나무 품종(品種)을 개발(開発)함에 있어서 큰 가능성(可能性)을 보여 주었다.