• Applied Biological Chemistry
• /
• 제26권1호
• /
• pp.58-64
• /
• 1983

$28^{\circ}C$에서 자란 $3{\sim}4$엽기 벼잎조직의 인지질지방산분석을 통해 벼품종별 상대적내냉성정도와 인지질지방산조성간에 성립되는 밀접한 상관관계를 확인하였다. 즉 내냉성이 강한 품종일수록 불포화도 및 불포화지방산의 구성비가 노은 인지질을 함유하고 있다. 인지질의 불포화상태를 나타내는 모든 지표들이 각품종의 냉해저항성과 잘 일치된다는 사실은, 곧 식물세포가 저온에서 생체막과 관련된 생리적활성을 유지하는데 있어서 필수조건으로 알려진 '생체막의 유동성'은 인지질지방산조성에 의해 절대적으로 지배받는다는 것을 분명히 나타낸다. 한편 벼의 인지질은 최소한 유묘기의 잎에서는 모든 품종에서 공히 phosphatidyl serine과 phosphatidyl choline을 주성분으로 phosphatidyl inositol을 부성분으로, 그밖에 3종의 미량성분을 포함하고 있으며, 인지질의 종류 및 조성은 내냉성과 무관한 것으로 판단된다.

• 한국표면공학회지
• /
• 제43권1호
• /
• pp.25-30
• /
• 2010

Titanium and titanium alloys are widely used for orthopedic and dental implants for their superior mechanical properties, low modulus, excellent corrosion resistance and good biocompatibility. In this study, corrosion behaviors of nanotube formed on the bone plate of Ti-6Al-4V alloy for dental use have been investigated. $TiO_2$ nanotubes were formed on the dental bone plates by anodization in $H_3PO_4$ containing 0.6 wt % NaF solution at $25^{\circ}C$. Electrochemical experiments were performed using a conventional three-electrode configuration with a platinum counter electrode and a saturated calomel reference electrode. Anodization was carried out using a scanning potentiostat (EG&G Co, Model 263A USA), and all experiments were conducted at room temperature. The surface morphology was observed using field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy(EDS). The corrosion behavior of the dental bone plates was examined using potentiodynamic test(potential range of -1500~2000 mV) in a 0.9% NaCl solution by potentiostat (EG&G Co, PARSTAT 2273. USA). The inner diameter of nanotube was about 150~180 nm with wall thickness of about 20 nm. The interspace of nanotube to nanotube was 50 nm. The passive region of the nanotube formed bone plates showed the broad range compared to non-nanotube formed bone plates. The corrosion surface of sample was covered with corrosion products.

• Journal of the Optical Society of Korea
• /
• 제20권6호
• /
• pp.807-812
• /
• 2016

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in only part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_s$). To address these problems, this study introduced hybrid layers of ITO/Ag/ITO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thicknesses of the metal interlayer. The $R_s$ of ITO(40)/Ag/ITO(40 nm) hybrid TFHs were 5.33, 3.29 and $2.15{\Omega}/{\Box}$ for Ag thicknesses of 10, 15, and 20 nm, respectively, while the $R_s$ of an ITO monolayer (95 nm) was $59.58{\Omega}/{\Box}$. The maximum temperatures of these hybrid TFHs were 92, 131, and $145^{\circ}C$, respectively, under a voltage of 3 V. And that of the ITO monolayer was only $32^{\circ}C$. For the same total thickness of 95 nm, the heat generation rate (HGR) of the hybrid produced a temperature approximately $100^{\circ}C$ higher than the ITO monolayer. It was confirmed that the film with the lowest $R_s$ of the samples had the highest HGR for the same applied voltage. Overall, hybrid layers of ITO/Ag/ITO showed excellent performance for HGR, uniformity of heat distribution, and thermal response time.

• 생명과학회지
• /
• 제21권1호
• /
• pp.134-140
• /
• 2011

대전일원의 유류오염 지역의 토양으로부터 원유를 단일 탄소원으로 이용하는 총 145균주를 순수분리 하였고, 이중 생물 계면활성제 생성능이 가장 우수한 한 균주를 최종 선별하여 형태 및 생리 생화학적 특성을 조사하고 16S rRNA 염기서열을 분석을 통하여 동정한 결과 Pseudomonas sp.로 확인되어 Pseudomonas sp. Z1이라 명명하였다. 최종 선별된 Pseudomonas sp. Z1은 클로람페니콜과 암피실린 등의 항생제와 리튬, 망간, 바륨 등의 중금속에 대해 강한 내성을 갖고 있었고, 최적 온도와 pH는 각각 $30^{\circ}C$와 pH 6.0-7.0으로 확인되었다. Pseudomonas sp. Z1이 생성하는 생물 계면활성제는 배양 10시간 이후부터 배양액의 표면장력이 급격히 감소해, 배양 21시간 후에 최대 28 dyne/cm까지 감소되었고, 2% 이상의 NaCl을 첨가한 경우 배양액의 생물계면활성제의 활성이 감소하였다.

• 한국수소및신에너지학회논문집
• /
• 제17권2호
• /
• pp.204-211
• /
• 2006

The electrolyte in the solid oxide fuel cell must be dense enough to avoid gas leakage and thin enough to reduce the ohmic resistance. In order to manufacture the thin and dense electrolyte layer, 8 mol% $Y_2O_3$ stabilized-$ZrO_2$ (8YSZ) electrolyte layers were coated on the porous tubular substrate by the novel vacuum slurry dip-coating process. The effects of the slurry concentration, presintering temperature, and vacuum pressure on the thickness and the gas permeability of the coated electrolyte layers have been examined in the vacuum slurry coating process. The vacuum-coated electrolyte layers showed very low gas permeabilities and had thin thicknesses. The single cell with the vacuum-coated electrolyte layer indicated a good performance of $495\;mW/cm^2$, 0.7 V at $700^{\circ}C$. The experimental results show that the vacuum dip-coating process is an effective method to fabricate dense thin film on the porous tubular substrate.

• 한국수소및신에너지학회논문집
• /
• 제26권5호
• /
• pp.416-422
• /
• 2015

Lithium Ion capacitor (LIC) is a new storage device which combines high power density and high energy density compared to conventional supercapacitors. LIC is capable of storing approximately 5.10 times more energy than conventional EDLCs and also have the benefits of high power and long cycle-life. In this study, LICs are assembled with activated carbon (AC) cathode and pre-doped graphite anode. Cathode material of natural graphite and artificial graphite kinds of MAGE-E3 was selected as the experiment proceeds. Super-P as a conductive agent and PTFE was used as binder, with the graphite: conductive agent: binder of 85: 10: 5 ratio of the negative electrode was prepared. Lithium doping condition of current density of $2mA/cm^2$ to $1mA/cm^2$, and was conducted by varying the doping. Results Analysis of Inductively Coupled Plasma Spectrometer (ICP) was used and a $1mA/cm^2$ current density, $2mA/cm^2$, when more than 1.5% of lithium ions was confirmed that contained. In addition, lithium ion doping to 0.005 V at 10, 20 and $30^{\circ}C$ temperature varying the voltage variation was confirmed, $20^{\circ}C$ cell from the low internal resistance of $4.9{\Omega}$ was confirmed.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.181-184
• /
• 2017

Multilayer ceramics in which piezoelectric layers of $0.90Pb(Zr_{0.48}Ti_{0.52})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.05Pb(Zn_{1/3}Nb_{2/3})O_3$ (0.90PZT-0.05PMS-0.05PZN) stack alternately with silver electrode layers were prepared by an advanced low-temperature co-fired ceramic (LTCC) method. The electrical properties and bonding strength of the multilayers were associated with the interface morphologies between the piezoelectric and silver-electrode layers. Usually, the inner silver electrodes are fabricated by sintering silver paste in multi-layer stacks. To improve the interface bonding strength, piezoelectric powders of 0.90PZT-0.05PMS-0.05PZN with an average particle size of $23{\mu}m$ were added to silver paste to form a gradient interface. SEM observation indicated clear interfaces in multilayer ceramics without powder addition. With the increase of piezoelectric powder addition in the silver paste, gradient interfaces were successfully obtained. The multilayer ceramics with gradient interfaces present greater bonding strength as well as excellent piezoelectric properties for 30~40 wt% of added powder. On the other hand, over addition greatly increased the resistance of the inner silver electrodes, leading to a piezoelectric behavior like that of bulk ceramics in multilayers.

• 한국해양공학회지
• /
• 제27권5호
• /
• pp.93-98
• /
• 2013

Fuel gas is an important energy source that is being increasingly used because of the convenience and clean energy provided. Natural gas is supplied to consumers safely through an underground gas-pipe network made of a polyethylene material. In electrofusion, which is one of the joining methods used, copper wire is used as the heating wire. However, it takes a long time for fusion to occur because the electrical resistance of copper is low. In this study, therefore, electrofusion was conducted by replacing the copper heating wire with carbon fiber to reduce the fusion time and improve the production when joining large pipes. Fusion and tensile tests were performed after the electrofusion joint was made in the polyethylene pipe using carbon fiber. The results showed that the fusion time was shorter and the temperature inside the pipe was higher with an increase in the current value. The ultimate tensile strength of specimens was higher than that of virgin polyethylene pipe, except for polyethylene pipes joined using a current of 0.8 A. The best fusion current value was 0.9 or 1.0 A because of the short fusion time and lack of transformation inside the pipe. Thus, it was shown that carbon fiber can be used to replace the copper heating wire.

• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.52-58
• /
• 2012

Hydrogen-delayed fracture (HDF) was analyzed from the deposited weld metals of 600-MPa and 800-MPa flux-cored arc (FCA) welding wires, and then from the diffusible hydrogen behavior of the weld zone. Two types of deposited weld metal, that is, rutile weld metal and alkali weld metal, were used for each strength level. Constant loading test (CLT) and thermal desorption spectrometry (TDS) analysis were conducted on the hydrogen pre-charged specimens electrochemically for 72 h. The effects of microstructures such as acicular ferrite, grain-boundary ferrite, and low-temperature-transformation phase on the time-to-failure and amount of diffusible hydrogen were analyzed. The fracture time for hydrogen-purged specimens in the constant loading tests decreased as the grain size of acicular ferrite decreased. The major trapping site for diffusible hydrogen was the grain boundary, as determined by calculating the activation energies for hydrogen detrapping. As the strength was increased and alkali weld metal was used, the resistance to HDF decreased.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2016년도 추계학술대회
• /
• pp.819-820
• /
• 2016

수배전분야는 고압 수배전반, 저압 수배전반, 모터 컨트롤 센터(motor control center; MCC)로 구성되며, MCC는 모터의 운전 및 정지를 할 수 있고, 이상상황 발생 시 비상정지 및 이상 상황에 대한 통보를 할 수 있도록 전자식 모터보호계전기(electronic over current relay; EOCR)가 사용되고 있다. 기존 EOCR은 과전류, 부족전류, 결상, 역상, 전류 불평형, 지락과 같은 전기적 결함 탐지는 가능하지만, 구속보호, 모터 고정자 및 회전자, 베어링 결함과 같은 기계적 결함은 탐지가 어렵다. 본 논문에서는 모터의 전기적, 기계적 결함을 탐지하기 위해 기존 EOCR의 전기적 결함 탐지에 기계적 결함 탐지를 결합하여 회전기기 보호장치를 위한 전기적인 결함과 기계적인 결함을 통합적으로 탐지할 수 있는 시스템을 제안한다. 회전기기 결함탐지를 위한 신호입력부 및 제어부, 시스템 인터페이스, 데이터 획득장치를 설계하였으며, 절연저항 측정, 모터 구속 측정 및 제어, MC 카운터 및 베어링 온도 측정 및 제어를 통해 전기적 결함과 기계적 결함 탐지가 가능하였다.