• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.219-224
• /
• 2001

Pd/Ge/Ti/Pt ohmic contact to n-type InCaAs was investigated. Minimum specific contact resistivity of $3.7\times10^{-6}\; \Omega\textrm{cm}^2$ was achieved by rapid thermal annealing at $400^{\circ}C$ for 10 seconds. This was related to the formation of Pd-Ge compounds and the in-diffusion of Ge atoms to InGaAs surface. However, the specific contact resistivity increased slightly to $low-10^5\; \Omega\textrm{cm}^2$ in the case of longer annealing time. Superior ohmic contact and non-spiking planar interface between ohmic materials and InGaAs were maintained after annealing at high temperature. Therefore, this thermally stable ohmic contact system is a promising candidate for compound semiconductor devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.308-309
• /
• 2012

One of the critical issues in the growth of multijunction solar cell is the formation of a highly doped Esaki interband tunnel diode which interconnects unit cells of different energy band gap. Small electrical and optical losses are the requirements of such tunnel diodes [1]. To satisfy these requirements, tens of nanometer thick gallium arsenide (GaAs) can be a proper candidate due to its high carrier concentration in low energy band gap. To obtain highly doped GaAs in molecular beam epitaxy, the temperatures of Si Knudsen cell (K-cell) for n-type GaAs and Be K-cell for p-type GaAs were controlled during GaAs epitaxial growth, and the growth rate is set to 1.75 A/s. As a result, the doping concentration of p-type and n-type GaAs increased up to $4.7{\times}10^{19}cm^{-3}$ and $6.2{\times}10^{18}cm^{-3}$, respectively. However, the obtained n-type doping concentration is not sufficient to form a properly operating tunnel diode which requires a doping concentration close to $1.0{\times}10^{19}cm^{-3}$ [2]. To enhance the n-type doping concentration, n-doped GaAs samples were grown with a lower growth rate ranging from 0.318 to 1.123 A/s at a Si K-cell temperature of $1,180^{\circ}C$. As shown in Fig. 1, the n-type doping concentration was increased to $7.7{\times}10^{18}cm^{-3}$ when the growth rate was decreased to 0.318 A/s. The p-type doping concentration also increased to $4.1{\times}10^{19}cm^{-3}$ with the decrease of growth rate to 0.318 A/s. Additionally, bulk resistance was also decreased in both the grown samples. However, a transmission line measurement performed on the n-type GaAs sample grown at the rate of 0.318 A/s showed an increased specific contact resistance of $6.62{\times}10^{-4}{\Omega}{\cdot}cm^{-2}$. This high value of contact resistance is not suitable for forming contacts and interfaces. The increased resistance is attributed to the excessively incorporated dopant during low growth rate. Further studies need to be carried out to evaluate the effect of excess dopants on the operation of tunnel diode.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.201-206
• /
• 2002

Pd/Si/Pd/Ti/Au ohmic contact to n-type InGaAs was investigated with rapid thermal annealing conditions. Minimum specific contact resistivity of $3.9\times10^{-7}\Omega\textrm{cm}^2$ was achieved at $400^{\circ}C$/20sec. This was related to the formation of Pd-Si compounds by rapid thermal annealing and the in-diffusion of Si atoms to InGaAs surface. However, the specific contact resistivity increased slightly to low-$10^{-6}\Omega \textrm{cm}^2$ at $400^{\circ}C$ for longer than 30 seconds, and to high-$10^{-7}$ at 425~$450^{\circ}C$ for 10 seconds. This resulted from the formation of Pd-Ga compounds. Superior ohmic contact and non-spiking planar interface between ohmic materials and InGaAs were maintained after annealing at high temperature. Therefore, this thermally stable ohmic contact system is a promising candidate for compound semiconductor devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.151-154
• /
• 1998

We have investigated a correlation of the electrical properties of the Pd/Ge/Pd/Ti/Au ohmic contact on n-InGaAs with its microstructures for the high temperature application of compound semiconductor devices. The samples were heat-treated by the rapid thermal annealing at various temperatures. In the contact system, moderately good specific contact resistance was obtained even before annealing because of the low metals-InGaAs barrier height, and better ohmic performances were observed by annealing up to 400˚C. But the ohmic performance was degraded after annealing at 450˚C due to the increment of Pd$_2$Ga$\sub$5/ phases.

• ETRI Journal
• /
• v.24 no.5
• /
• pp.349-359
• /
• 2002

With Ni/Au and Pd/Au metal schemes and low temperature processing, we formed low resistance stable Ohmic contacts to p-type GaN. Our investigation was preceded by conventional cleaning, followed by treatment in boiling $HNO_3$:HCl (1:3). Metallization was by thermally evaporating 30 nm Ni/15 nm Au or 25 nm Pd/15 nm Au. After heat treatment in $O_2$ + $N_2$ at various temperatures, the contacts were subsequently cooled in liquid nitrogen. Cryogenic cooling following heat treatment at $600^{\circ}C$ decreased the specific contact resistance from $9.84{\times}10^{-4}$ ${\Omega}cm^2$ to $2.65{\times}10^{-4}$ ${\Omega}cm^2$ for the Ni/Au contacts, while this increased it from $1.80{\times}10^{-4}$ ${\Omega}cm^2$ to $3.34{\times}10^{-4}$ ${\Omega}cm^2$ for the Pd/Au contacts. The Ni/Au contacts showed slightly higher specific contact resistance than the Pd/Au contacts, although they were more stable than the Pd contacts. X-ray photoelectron spectroscopy depth profiling showed the Ni contacts to be NiO followed by Au at the interface for the Ni/Au contacts, whereas the Pd/Au contacts exhibited a Pd:Au solid solution. The contacts quenched in liquid nitrogen following sintering were much more uniform under atomic force microscopy examination and gave a 3 times lower contact resistance with the Ni/Au design. Current-voltage-temperature analysis revealed that conduction was predominantly by thermionic field emission.

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.24-28
• /
• 1998

Pd/Ge ohmic contact system on n-type InGaAs was studied. A good ohmic begavior by rapid thermal annealing was shown up to $400^{\circ}C$, and the specific contact resistance was reduced to low-$10^-6\Omega\textrm{cm}^2$EX>. However, above $425^{\circ}C$ it was deteriorated by intermixing and phase reaction of ohmic metals and InGaAs substrate. No remarkable phase change was observed below $350^{\circ}C$, but the reaction was initiated at ~$375^{\circ}C$ and considerable phase change was found above $425^{\circ}C$. Non-spiking and planar interfaces were observed even when annealed at $425^{\circ}C$, and smooth and shiny surface was kept up to $400^{\circ}C$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.20-20
• /
• 2003

We developed 30 ㎽-AlInGaN based violet laser diodes. The fabrication procedures of the laser diodes are described as follows. Firstly, GaN layers having very low defect density were grown on sapphire substrates by lateral epitaxial overgrowth method. The typical dislocation density was about 1-3$\times$10$^{6}$ /$\textrm{cm}^2$ at the wing region. Secondly, AlInGaN laser structures were grown on LEO-GaN/sapphire substrates by MOCVD. UV activation method, instead of conventional annealing, was conducted to achieve good p-type conduction. Thirdly, ridge stripe laser structures were fabricated. The cavity mirrors were formed by cleaving method. Three pairs of SiO$_2$ and TiO$_2$ layers were deposited on the rear facet for mirror coating. Lastly, laser diode chips were mounted on AlN submount wafers by epi-down bonding method. The lifetime of the laser diodes was over 10,000 hrs at room temperature under automatic power controlled condition. We expect the performance of the LDs to be improved by the optimization of the growth and fabrication process. The detailed characteristics and important issues of the laser diodes will be discussed at the conference.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.8
• /
• pp.15-23
• /
• 1998

Single crystalline I $n_{x}$G $a_{1-x}$ N thin film was grwon by MOCVD on (001) sapphire substrate for the blue light emitting devices. A good quality of I $n_{0.13}$G $a_{0.87}$N/GaN heterostructure grwon above 700.deg. C was confiremed by various characterization techniques of AFM, RHEED and DC-XRD. Through PL measurement at room temperautre for the Si-Zn co-doped I $n_{x}$G $a_{a-x}$N/GaN structure grwon at 800.deg. C to obtain blue wavelength emission, 460-470 nm and 425 nm emission peak were observed, which are believed to be from donor-to-acceptor pair transition and band edge emission of In/x/G $a_{1-x}$ N, respectively. The result of PL measurement of the undoped MQW I $n_{x}$G $a_{1-x}$ N layer at low temperature confirmed that the strong MQW peak was resulted by exciton from the GAN barrier and carrier of DA pair confined into the well layer.ll layer.yer.r.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.1-12
• /
• 2003

This paper describes a study on the abnormal behavior of the electrical characteristics of the (n)GaAs/Ti/Pt/Au Schottky contacts prepared by the two techniques of electron beam deposition and rf sputtering and after an annealing treatment. The samples were characterized by I-V and C-V measurements carried out over the temperature range of 150 - 350 K both in the as prepared state and after a 300 C, 30 min. anneal step. The variation of ideality factor with forward bias, the variation of ideality factor and barrier height with temperature and the difference between the capacitance barrier and current barrier show the presence of a thin interfacial oxide layer along with barrier height inhomogenieties at the metal/semiconductor interface. This barrier height inhomogeneity model also explains the lower barrier height for the sputtered samples to be due to the presence of low barrier height patches produced because of high plasma energy. After the annealing step the contacts prepared by electron beam have the highest typical current barrier height of 0.85 eV and capacitance barrier height of 0.86 eV whereas those prepared by sputtering (at the highest power studied) have the lowest typical current barrier height of 0.67 eV and capacitance barrier height of 0.78 eV.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.81-85
• /
• 2015

The organic/inorganic hybrid photovoltaic devices have been studied using Poly(3-hexylthiophene-2,5-diyl) (P3HT) : [6, 6]-Phenyl C61 butyric acid methyl ester (PCBM) and GaN. We traced the effect of short circuit current density with different annealing method under the various concentration and ratio of P3HT:PCBM. During the pre-annealing course, the heat treatments were performed each time at low temperature after the organic layer coated and the samples were heated at high temperature through one or two steps under the post-annealing process. It revealed that the samples with post-annealing process had higher values of short circuit current density than the other samples upon pre-annealing. And the interesting high short circuit current density features were observed at 1:1 mixing ratio and 1wt% of P3HT:PCBM.