• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1772-1782
• /
• 1993

The characteristics of metal matrix composite under dynamic tension at high strain rates up to the order of $10^3/sec$ is studied by using newly developed apparatus. The composite material processed in this research is aluminum-alumina metal matrix composites, arid fabricated by compocasting with the fiber volume fraction from 5 to 20%. The whisker and matrix material used in this paper were ${\delta}-Al_2O_3$ and Al-6061, respectively. The mechanical tests performed in this research are low and high strain rate tensile test. At low strain-rate tensile test, the modulus of elasticity and the ultimate tensile strength of the composites were improved about 77 pct. and 55 pct., respectively comparing with the unreinforced materials. At strain-rate from $10^{-3}\;to\;10^3/s$, the effect of strain-rate on the modulus, ultimate strength, flow stress is determined. Also the effect of strain rate on the modulus, ultimate tensile strength, flow stress and elongation to failures were investigated.

• Nuclear Engineering and Technology
• /
• 제43권1호
• /
• pp.83-88
• /
• 2011

To define the effect of strain rate variation from 0.04% to 0.004%/s on environmental fatigue of CF8M cast stainless steel, which is used as a primary piping material in nuclear power plants, low-cycle fatigue tests were conducted at operating pressure and temperature condition of a pressurized water reactor, 15 MPa and $315^{\circ}C$, respectively. A high-pressure and high-temperature autoclave and cylindrical solid fatigue specimens were used for the strain-controlled low-cycle environmental fatigue tests. It was observed that the fatigue life of CF8M stainless steel is shortened as the strain rate decreases. Due to the effect of test temperature, the fatigue data of NUREG-6909 appears a slightly shorter than that obtained by KEPRI at the same stress amplitude of $1{\times}10^3$ MPa. The environmental fatigue correction factor $F_{en}$'s calculated with inputs of the test data increases with high strain amplitude, while the $F_{en}$'s of NUREG-6909 remain constant regardless of strain amplitude.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.521-527
• /
• 2002

In this paper, tensile behavior and low cycle fatigue behavior of 316L stainless steel which is currently favored structural material for several high temperature components such as the liquid metal cooled fast breeder reactor (LMFBR) were investigated. Research was performed at 55$0^{\circ}C$, $600^{\circ}C$ and $650^{\circ}C$ since working temperature of 316L stainless steel in a real field is from 40$0^{\circ}C$ to $650^{\circ}C$. From tensile tests performed by strain controls with $1{\times}10^{-3}/s,\; l{\times}10^{ -4}/s \;and\; 1{\times}10/^{ -5}/ s $ strain rates at each temperature, negative strain rate response (that is, strain hardening decreases as strain rate increases) and negative temperature response were observed. Strain rate effect was relatively small compared with temperature effect. LCF tests with a constant total strain amplitude were performed by strain control with a high temperature extensometer at R.T, 55$0^{\circ}C$, $600^{\circ}C$, $650^{\circ}C$ and total strain amplitudes of 0.3%~0.8% were used and test strain rates were $1{times}10^{-2} /s,\; 1{times}10^{-3} /s\; and\; 1{times}10^{-4} /s$. A new energy based LCF life prediction model which can explain the effects of temperature, strain amplitude and strain rate on fatigue life was proposed and its excellency was verified by comparing with currently used models.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.18-21
• /
• 2009

높은 열하중하에 있는 부품의 수명은 일반적으로 다른 부품에 비해 짧은 수명을 가지고 있다. 액체 로켓의 터보펌프 터빈은 작동시간 동안 높은 회전속도로 인한 높은 원심력과 높은 온도와 같은 환경하에서 작동된다. 이와 같은 환경은 터보펌프 터빈의 저주기 피로를 야기한다. 우선 열응력을 해석하기 위해 ABAQUS/CAE가 사용되었으며 탄성변형률과 소성변형률을 고려하기 위해 Coffin-Manson 방정식을 사용하였다. 평균응력의 변화를 고려하기 위해 S.W.T법을 사용하였으며, 열응력해석 결과로 얻어진 변형률 이력을 이용하여 터보펌프 터빈의 취약지점에 저주기피로해석을 수행하였다. 본 연구에서는 저주기 수명을 해석하기 위해 변형룰 수명 방법이 적용되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권1호
• /
• pp.55-63
• /
• 2012

이 연구에서는 타설 과정에서 낮은 점성이 요구되는 구조물에 적합한 낮은 점성을 가지면서 다중균열에 의한 변형률 경화거동을 보이는 고인성 섬유복합재료를 제조하기 위한 재료와 제조 방법을 제시하고자 한다. 섬유복합재료의 낮은 점성과 고인성을 얻기 위하여 미시역학과 파괴역학에 기반한 이론적 해석 방법과 제조 기법을 적용하였다. 2~3MPa 범위의 인장강도를 갖는 복합재료에 적합한 최적의 섬유 양과 길이, 그리고 섬유와 매트릭스의 계면 특성을 미시역학과 안정상태 균열 이론을 이용하여 해석적으로 구한 후 여섯 가지 배합을 결정하였다. 여섯 가지 배합으로 제조한 실험체는 실험을 통하여 점성과 일축인장 성능을 검증하였다. 실험 결과 굳기 전에는 그라우팅에 적합한 낮은 점성을 갖으면서 굳은 후에는 1.5% 이상의 고인성을 갖는 변형률 경화 섬유복합재료를 제조할 수 있는 것으로 나타났다.

• 반도체디스플레이기술학회지
• /
• 제13권4호
• /
• pp.33-36
• /
• 2014

In this paper, a carbon strain gauge for large strain was developed. The carbon strain gauge was fabricated by forming PCB and antenna pattern using Cu/Ni/Au film and carbon resistor pattern using screen printing process on plastic film substrate. It was possible to develop low-cost disposable strain gauge since the carbon paste was cheap and the fabrication process was simple. The wireless communication type carbon strain gauge was fabricated by integrating signal processing circuit, antenna and power all together on the same substrate as a strain gauge. The wireless communication type carbon strain gauge has a merit of being available immediately at the spot without any particular system.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.174-181
• /
• 2000

A brief review of previous studies on the behaviour of concrete at extremely low temperature is presented in this paper. In addition, to describe temperature dependent behaviour of concrete, simple piecewise linear stress-strain relation is introduced. The proposed curve shows good agreement with experimental stress-strain curves at various temperature conditions. Moreover, numerical analyses for two PC beams are conducted to verify the influence of extremely low temperature to the structural behaviour.

• 한국항공우주학회지
• /
• 제49권10호
• /
• pp.813-820
• /
• 2021

본 연구에서는 고체추진제의 동적 응력-변형률 특성을 고찰하기 위하여 저속충격시험을 수행하였다. 저속충격시험 시 충격체(Impactor)의 하중, 변위를 측정하여 고체추진제의 동적 거동을 확인하였다. 3점 굽힘 형태의 저속충격시험을 수행하였고, 이때 발생하는 국소변위와 길이가 짧고 두께가 두꺼운 고체추진제 시편의 전단 변위를 보상하여 순수 굽힘변위를 계산하였다. 보상된 변위와 측정된 하중을 사용하여 응력과 변형률을 계산하였고 응력-변형률 곡선으로부터 고체추진제의 동적 물성을 획득하여 이를 정적 굽힘 물성과 비교하였다. 운용 환경에 따른 온도별 고체추진제의 동적 물성을 획득하기 위해 상온, 고온, 저온에서 실험을 수행하고 결과를 비교분석하였다.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1398-1408
• /
• 2003

Tensile and LCF(low cycle fatigue) tests were carried out in air at wide temperature range 20$^{\circ}C$-750$^{\circ}C$ and strain rates of 1${\times}$10$\^$-4//s-1${\times}$10$\^$-2/ to ascertain the influence of strain rate on tensile and LCF properties of prior cold worked 316L stainless steel, especially focused on the DSA(dynamic strain aging) regime. Dynamic strain aging induced the change of tensile properties such as strength and ductility in the temperature region 250$^{\circ}C$-600$^{\circ}C$ and this temperature region well coincided with the negative strain rate sensitivity regime. Cyclic stress response at all test conditions was characterized by the initial hardening during a few cycles, followed by gradual softening until final failure. Temperature and strain rate dependence on cyclic softening behavior appears to result from the change of the cyclic plastic deformation mechanism and DSA effect. The DSA regimes between tensile and LCF loading conditions in terms of the negative strain rate sensitivity were well consistent with each other. The drastic reduction in fatigue resistance at elevated temperature was observed, and it was attributed to the effects of oxidation, creep and dynamic strain aging or interactions among them. Especially, in the DSA regime, dynamic strain aging accelerated the reduction of fatigue resistance by enhancing crack initiation and propagation.

• 대한기계학회논문집B
• /
• 제29권9호
• /
• pp.988-996
• /
• 2005

Flame structure and extinction mechanism of counterflow methane/air non-premixed flame diluted with nitrogen are studied by NASA 2.2 s drop tower experiments and two-dimensional numerical simulations with finite rate chemistry and transport properties. Extinction mechanism at low strain rate is examined through the comparison among results of microgravity experiment, 1D and 2D simulations with a finite burner diameter. A two-dimensional simulation in counterflow flame especially with a finite burner diameter is shown to be very important in explaining the importance of multidimensional effects and lateral heat loss in flame extinction, effects that cannot be understood using a one-dimensional flamelet model. Extinction mechanism at low strain rate is quite different from that at high strain rate. Low strain rate flame is extinguished initially at the outer flame edge, the flame shrinks inward, and finally is extinguished at the center. It is clarified from the overall fractional contribution by each term in energy equation to heat release rate that the contribution of radiation fraction with 1D and 2D simulations does not change so much and the overall fractional contribution is decisively attributed to radial conduction ('lateral heat loss'). The experiments by Maruta et at. can be only completely understood if multi-dimensional heat loss effects are considered. It is, as a result, verified that the turning point, which is caused only by pure radiation heat loss, has to be shifted towards much lower global strain rate in microgravity flame.