• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.54-58
• /
• 1988

In order to depress PbO vaporization during calcination and improve sinterability in low temperature, a method for preparing homogeous Lead-Zirconate-Titanate (PZT) powder from aqueous salt solution by precipitation is described. In this method, single phae PZT fine powders are formed at above 500$^{\circ}C$. PZT-ceramics using these powders have high sinterability, and good sintering characteristics relatively low temp. (-high apparent density, low porosity, low water adsorption etc.)

• Journal of Powder Materials
• /
• v.19 no.2
• /
• pp.127-133
• /
• 2012

The sintering behaviors and process parameters of some compounds (carbides, oxides, sulfides, borides) were investigated experimentally. These compounds were successfully consolidated and showed high densities. Some unique phenomena such as retardation of grain growth, suppression of thermal decomposition and maintenance of initial non-equilibrium phases, were observed by the proper control of process in spark sintering.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.855-861
• /
• 2006

Sinterability and microwave dielectric properties of $xZWO_{4}-(1-x)TiO_{2}$ ceramic systems with zinc-borosilicate glass and $TiO_{2}$ contents for LTCC(Low Temperature Co-fired Ceramics) were investigated. The addition of $3{\sim}10\;wt%$ ZBS glass ensured the sinterability below $900^{\circ}C$. In general, increasing ZBS glass content seemed to enhance the sinterability, but the quality factor($Qxf_{0}$) significantly decreased due to the formation of an excessive liquid and second phases. As for the addition of $TiO_{2}$, the dielectric constant(${\varepsilon}_{r}$) and temperature coefficient of resonant frequency(${\tau}_{f}$) showed to increase, while the quality factor($Qxf_{0}$) did not show an apparent change. The composition of $0.7xZnWO_{4}-0.3TiO_{2}$ ceramics sintered at $900^{\circ}C$ with 5 wt% ZBS glass demonstrated 21.6 in dielectric constant(${\varepsilon}_{r}$), 14,800 in quality factor($Qxf_{0}$), and $+5\;ppm/^{\circ}C$ in temperature coefficient of resonant frequency(${\tau}_{f}$).

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.845-851
• /
• 1993

Low firing temperature substrate were synthesized through tape casting and sintering of glass with cordierite composition and then their properties were investigated. Even though the dielectric properties and XRD patterns of substrates, obtained by tape casting and sintering at 900~100$0^{\circ}C$ for various periods, were similar to those of substrates obtained by dry pressing, the sinterability was enhanced. The substrates were thin and the size was 0.6$\times$50$\times$50mm. From the results of dielectric properties, the sinterability and X-ray diffraction pattern, the proper condition for cofiring process with conductor, Cu, was 90$0^{\circ}C$ for 1h. The properties of the substrate are as follows; the dielectric constant was 5.31(at 1MHz), the dissipation factor was 0.0028, the apparent porosity was 0.28% and the main crystalline phase was $\alpha$-cordierite.

• Journal of the Korean Ceramic Society
• /
• v.30 no.6
• /
• pp.429-432
• /
• 1993

Cr3C2 material is characterized by high chemical stability and poor sinterability with low strength [50~150MPa]. In his study, low melting temperature nickel powder was used to improve sinterability as well as strength. In addition, molydenum particles were added to the Ni-bonded Cr3C2 cermet pseudomatrix to increase resistance to fracture. The specimens made by hot-pressing under vacuum and strength was measured by 4-point bending. Indentation cracking and fractographic examination were conducted to study the interaction of the indentation cracks with the reinforcing particles. Toughening mechanisms and failure will be discussed in terms of crack/particle interactions and compared with previous works.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.200-210
• /
• 2009

It is necessary to minimize the mismatch of sintering shrinkage between dielectric ceramic and Ni inner electrode layers for the purpose of developing the ultra high-capacity multi layered ceramic condenser(MLCC). Thus, low temperature sintering of dielectric $BaTiO_3$ ceramic should be precedently investigated. In this work, the influence of the milling condition on sintering behavior and electrical properties of $BaTiO_3$ ceramics was investigated in the $BaTiO_3$(BT)-Mg-Dy-Mn-Ba system with borosilicate glass as a sintering agent. As milling time increased, specific surface area(SSA) of the powder increased linearly, while both sinterability and dielectric property were found to be drastically decreased with an increasing SSA. It was also revealed that the sinterability of the excessively milled $BaTiO_3$ ceramics could be recovered by increasing Ba content, rather than increasing glass addition. These results suggest that the sintering behavior of $BaTiO_3$ ceramics under the high SSA was more strongly dependent on the transient liquid phase caused by Ba addition, than the liquid phase from additional glass.

• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.1-8
• /
• 1992

The effect of CaO impurity on the microstructural evolution during the sintering of ultrapure alumina(>99.999%) was studied under "clean" firing conditions. The sinterability of undoped alumina was low, but its microstructure was maintained uniform. In the case of CaO-doped alumina, the distribution of grain size and that of grain boundary dihedral angle became wider, and facetted pores observed frequently. When MgO was doped in addition to CaO, the sinterability increased drastically and the uniform microstructural characteristics resumed. This study suggests that the effect of CaO is to induce inhomogeneous microstructures presumably by anisotropic segregation to grain boundaries and pore surfaces, and that MgO suppresses the anisotropic segregation of Ca.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.242-248
• /
• 1989

The powder properties and sinterability of ZrO2-8m/o Y2O3 prepared by coprecipitation were investigated. The specific surface area and the total pore volume were increased with increasing pH of sediment and using of ethyl alcohol for washing. The powders of prepared by freeze drying method were showed the smallest particle size and lowest agglomerate rate, and the powders obtained from spray drying method were showed porous structure. At 130$0^{\circ}C$, their relative density were 94-96%, so these sintered bodies have revealed high sinterability in spite of low sintering temperature.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.168-172
• /
• 1988

In order to prevent the PbO vaporization during calcination and to produce the powder of good sinterability, a coprecipitation method for preparing homogeneous Lead-Zirconate-Titanate (PZT) powder from aqueous salt solution is described. In this method, the PZT-ceramics show low calcining and sintering temperature, and they have good sintering and electronic properties.

• Journal of the Korean Ceramic Society
• /
• v.28 no.6
• /
• pp.457-464
• /
• 1991

Aluminum nitride (AlN) has excellent properties such as high thermal conductivity and electrical resistivity, whereas it has some disadvantages such as low sinterability and tendency to be hydrolyzed by moisture at room temperature. In the present work, the relative density, modulus of rupture and microhardness were examined for pressure-less-sintered AlN (synthetic and commercial) bodies which were prepared under the conditions of various sintering temperatures, holding times and additions of CaCO3 which showed the best effect on sinterability among the various sintering aids. As a result, the AlN bodies with 1.0 wt% CaCO3 (0.56wt% CaO) which were sintered at 1800$^{\circ}C$ for 20 min showed good densification. In this case, the relative densities were 95.9% and 95.2%, and microhardnesses were 10.3 GPa and 9.8 GPa for synthetic and commercial AlN respectively. And as the holding time at 1800$^{\circ}C$ was increased from 10 min to 60 min, the relative density was increased from 91.9% to 96.5%. It was considered that impurities of metals and oxygen promoted the densification of AlN at low temperature (1600$^{\circ}C$).